Video Monitor WV-BM500 Before attempting to connect or operate this product, please read these instructions completely.
For U.K. ENGLISH VERSION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green-and-yellow.
CONTENTS PREFACE ....................................................................................................................................................................... 2 FEATURES ..................................................................................................................................................................... 2 PRECAUTIONS ........................................................................................................................................
PREFACE FEATURES • The Panasonic WV-BM500 is a desk-top closed circuit Video Monitor especially designed for surveillance and studio applications. WV-BM500 features a 5” screen (diagonal actual visual size) and produces sharp, black-and-white pictures with horizontal resolution of more than 700 lines at center. Front mounted controls permit fast picture adjustment. Standard BNC-type input and output connectors enables WV-BM500 to be used with other CCTV monitors or Panasonic Video Tape Recorder.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ON V.LIN HEIGHT OFF H.HOLD V.HOLD BRIGHT FOCUS CONTRAST POWER Video Monitor WV-BM q w r y i e t u 500 !0 o 1. Power On/Off Switch (POWER, ON/OFF) This is a push-push type switch which turns the power of this monitor on and off. Press once and the switch remains down (;) for turning on the power of monitor. !1 !2 !3 !4 !5 !6 Press again, the switch comes up (l) for turning off the power of the monitor. 2.
3. Horizontal Hold Control [H-HOLD] This control is used to Lock in the picture horizontally. 10. DC Restoration Switch [DC REST] Switch to restore background of picture. 4. Height Control [HEIGHT] Adjust the vertical height of the picture. 11. Video Input Connector (VIDEO IN) This connector accepts the input video signal 5. Vertical Hold Control [V-HOLD] This control is used to Lock in the picture vertically. 6. Vertical Linearity Control [V-LIN] Adjust for vertical distortion of the picture. 12.
5. Height (4) This recessed screwdriver control should be adjusted simultaneously to give proper vertical height consistent with good vertical linearity. Adjustment should be made to extend the picture limits approximately 1/10” beyond the top and bottom edges of the mask at over scanning operation. OPERATING PROCEDURE 1. Set the Power On/Off Switch (1) to the ON (;) position. 2. Adjust the Bright Control (7) and Contrast Control (9). increase BRIGHT 3.
INSTALLATION CAUTION: The following installation should be made by qualified service personnel or system installers. Mounting into EIA Standard 19” Rack Model WV-BM500 can be mounted into EIA 19” rack as shown below. Note: Rack Mounting requires the purchase of optional WV-Q64 Rack Angle Bracket. WV-BM500 Rack Panel EIA Rack Rack Mount Chassis Rack Mount Screws (Not Supplied) Washer (Part No. YWL1201ER01) Fixing Screws (Part No.
External Sync CONNECTIONS When a non-composite video signal is connected to the monitor, it will be necessary to connect an external composite sync signal to the monitor. 1. Connect the Sync Input Connector (14) on the video monitor to the sync signal source by means of a 75Ω coaxial cable. 2. Set the Sync Selector Switch (13) at EXT position. Power Cable 1. Keep the camera Power switched OFF during installation. 2. Connect the Power Cord (16) to a 50 Hz grounded electrical outlet 220-240V AC .
Internal Sync Connection SYSTEM CONNECTION 1. Single Monitor Connection • Connect the Video Input Connector (11) on the monitor to the Video Out Terminal of cameras with 75-ohm coaxial cables. WV-BM500 Camera External Sync Connection 220-240V AC 50 Hz Coax. Cable 2. Multiple Monitor Connection WV-BM500 Camera 220-240V AC 50 Hz Coax. Cable Coax.
SPECIFICATIONS Power Source : Power Consumption : Tube Size : Video Input Impedance : Video Input Level : Resolution : Scanning Frequency : Sweep Linearity : External Sync Input Impedance : External Sync Input Level : Operating Ambient Temperature : Operating Ambient Humidity : Dimensions : Weight : WV-BM500/A, WV-BM500/B, WV-BM500/G: 220-240V AC50Hz Approx. 14W 5” diagonal actual visual size 75Ω or high impedance (Auto Termination) 1.0 Vp-p composite (0.5 Vp-p - 2.
OPTIONAL ACCESSORY Rack Angle Bracket .........................................
Matsushita Electric Industrial Co., Ltd. Central P.O.
