Operating Instructions WJ-MP204 FRANÇAIS DEUTSCH Model No. ENGLISH Data Multiplex Unit ALARM D SUSPEN ALARM P204 it WJ-M plex Un ulti Data M ON OFF Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EEC-direktiv nr. 73/23 och 89/336.
PREFACE .................................................................................................................................................................................... 4 FEATURES .................................................................................................................................................................................. 4 COMMUNICATION MODE ................................................................................................................
PREFACE The WJ-MP204 Data Multiplex Unit enables you to remote control multiple surveillance cameras, check alarm settings, operate the cameras and control other system components when combined with the WV-CU360 System Controller with Panasonic Security Data mode capability. Using up to four Data Multiplex Units in daisy-chain connection allows expansion of the system to include up to 16 cameras. The distance between the system and the cameras can be extended by connecting an AV Codec or similar device.
COMMUNICATION MODE The WJ-MP204 Data Multiplex Unit can communicate with the WV-CU360 System Controller in Panasonic Security Data mode or Camera Communication mode. Both modes require different settings. Panasonic Security Data mode This mode lets you • Operate multiple cameras and devices via one WVCU360 System Controller. • Connect up to 16 Data Multiplex Units for Panasonic Security Data mode communication (up to 4 in case of the WJ-MP204). • Set a unit number for each Data Multiplex Unit.
MAJOR OPERATING CONTOROLS AND THEIR FUNCTIONS ■ Front View UNIT 9 0 1 2 3 POWER w 7 8 q e r ALARM RESET 4 5 6 ON OFF 1 t SUSPEND SET UP SET ESC 2 3 ALARM ALARM SUSPEND 4 Data Multiplex Unit WJ-MP204 y q Power Switch (POWER ON/OFF) Press once to turn on the Data Multiplex Unit. The switch remains down (;) and the LED lights up. Press again to turn off the unit. The switch comes up (l).
■ Rear View o IN 4 3 !1 2 1 !3 IN !5 IN T 4 3 CAMERA !0 2 1 OUT B R A B A SIGNAL GND OUT SPOT VS/VD RS485 DATA MODE !2 !4 !6 !7 !8 o Camera Input Connectors 1-4 (CAMERA IN 1, 2, 3, 4) These connectors accept the composite video signal from the camera. • Set MODE Switch (1) to ON (VD) in supplying the internally generated reference sync signal VD to other devices.
SETUP PROCEDURE Follow the procedures below for setup. Power Switch LED Power Switch UNIT 9 0 1 2 3 POWER 7 8 1. Press the Power Switch back to the OFF position. Check that the Power Switch LED is off. ALARM RESET 4 5 6 ON OFF 1 2 SUSPEND SET UP SET ESC 3 4 Data M 2. Set the MODE Switches as follows: Select an operation mode using the MODE Switches on the rear panel. See page 9 for details. • Communication mode This mode must be selected whenever this data multiplexer unit is used.
DIP SWITCH SETTING Before connecting the Data Multiplex Unit, check how the DIP switches are set on the rear panel in cases where the system setup must be changed. ■ Setting Communication Mode ● Data Line Selection Mode Set DIP Switch SW6 to the 4-LINE or 2-LINE position according to the desired data line selection mode. 4-LINE: Full Duplex 2-LINE: Half Duplex The initial factory setting is 4-LINE. ● Panasonic Security Data Mode 4-LINE Check that Dip Switches SW3 and SW4 are up.
SETTING ADDRESSES Address setting varies from one communication mode to another. The setting should be made by qualified service personnel or system installers. ■ Panasonic Security Data Mode Set each number as follows. UNIT Switch Settings of WJ-MP204 Unit address of WJ-MP204 0 1 2 3 4 5 6 7 8 9 Set the number in Setup menu 1 2 3 4 5 6 7 8 Prohibition of a Setup (reserved number) Notes: • Do not set the UNIT switch to position 9 because it is a reserved number.
SETUP MENU The Setup menu consists of two main menus: one for communication setup for connection to cameras and the system controller WV-CU360, and the other for system setup of the Data Multiplex Unit. Each of the main menus consists of submenus. The Setup menu varies between Panasonic Security Data mode and Camera Communication mode. Refer to the description of communication mode setting with the DIP switches on page 9.
■ Displaying the Setup Menu for Panasonic Security Data Mode 1. Check that the cameras and peripherals are connected correctly and securely. 2. Switch all the system components on. 3. Press the SETUP/ESC button for 2 seconds or more. The Setup menu appears on the monitor. WJ-MP204 SETUP MENU X.XX COMMUNICATION SYSTEM Note: • To not display the Setup menu for CAMERA OUT pictures, shift the internal switch.(See page 25.
(1) Unit Address Setting (6) Wait Time Setting 1. Display the COMMUNICATION menu. 2. Move the cursor to UNIT ADDRESS by pressing button 1 (C) or button 2 (D), then select the desired unit address in the range of 1 to 99 by pressing button 3 (–) or button 4 (+). Notes: • Check before the above setting that the UNIT switch is at 0. For address setting, see page 10. • Before switching the Data Multiplex Unit back on, remember that address setting with the UNIT switch has priority to the above setting. 1.
(1) Alarm Mode Setting OFF by pressing button 3 (–) or button 4 (+). The initial factory setting is ON. • Monitor Spot Setting ALARM MODE MONITOR SPOT ALARM DISPLAY SITE ALARM TERM.ALARM ALARM OUTPUT ALARM DATA ON ON ON ON 10S 1S 1. Display the SYSTEM menu. 2. Move the cursor to ALARM MODE by pressing button 1 (C) or button 2 (D), press the SUSPEND/SET button, then select MONITOR SPOT ON or OFF by pressing button 3 (–) or button 4 (+). The initial factory setting is ON.
(2) Comp/VD2/Data Setting COMP/VD2/DATA CAMERA IN 1CH COMP S VD2 ON DATA ON The initial factory setting is ON. (3) VS/VD Input 1. Display the SYSTEM menu. 2. Move the cursor to VS/VD INPUT by pressing button 1 (C) or button 2 (D), then select VS or VD by pressing button 3 (–) or button 4 (+). The initial factory setting is VD. (4) Camera Config • Camera Input Setting 1. Display the SYSTEM menu. 2.
■ Displaying the Setup Menu of Camera Communication Mode 1. Check that the cameras and peripherals are connected correctly and securely. 2. Switch all the system components on. 3. Press the SETUP/ESC button for 2 seconds or more. The Setup menu appears on the monitor. Notes: • To not display the Setup menu for camera output pictures, shift the internal switch. (See page 25.) • To finalize the settings, press the SETUP/ESC button for 2 seconds or more while the Setup menu is displayed.
(1) Camera Addresses Setting 1. Display the COMMUNICATION menu. 2. Move the cursor to CAM ADDRESS by pressing button 1 (C) or button 2 (D), press the SUSPEND/SET button, and then select the desired camera addresses in the range of 1 to 99 or No Camera by pressing button 3 (–) or button 4 (+). COMMUNICATION CAM ADDRESS BAUD RATE 19200 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 WAIT TIME OFF DELAY TIME OFF XON/XOFF NOT USE (4) Parity Check Setting 1. Display the COMMUNICATION menu. 2.
■ System Setup for Camera Communication Mode 1. Display the Setup menu. 2. Move the cursor to SYSTEM by pressing button 1 (C) or button 2 (D), then press the SUSPEND/SET button. • In case of Camera Communication mode, the SYSTEM menu appears as shown below. SYSTEM ALARM MODE ON COMP/VD2/DATA VS/VD INPUT VD DAISY MODE ON TERMINAL ALARM 3. Move the cursor to the desired item by pressing button 1 (C) or button 2 (D), and then select the desired mode by pressing button 3 (–) or button 4 (+). 4.
• Alarm Data This is to set whether or not the alarm data received from a camera is to be transmitted to the WV-CU360. POLLING: Disables to transmit to the system controller even if an alarm is activated. AUTO1: Enables to transmit to the system controller when an alarm is activated. AUTO2: Enables to transmit to the system controller when an alarm is activated. Ignores an alarm for 5 seconds after it has transmitted. Enable to transmit an alarm after it has elapsed for 5 seconds. 1.
INSTALLATION The installation described below should be made by qualified service personnel or system installers. ■ Mounting in the Rack Remove the four rubber feet by removing the four screws from the bottom of the WJ-MP204. Rubber feet ● Mounting One WJ-MP204 with the WVQ204/1 1. Fix the mounting brackets (large and small) on both sides of the WJ-MP204 with the eight supplied screws (M3x8). Rack mounting bracket (small) Rack mounting bracket (large) ● Mounting two WJ-MP204s With the WVQ204/2 1.
SYSTEM CONNECTION ■ BASIC SYSTEM CONNECTION (Panasonic Security Data Mode) The Data Multiplex Unit WJ-MP204 may be connected to cameras, video monitors, and system controller WV-CU360 as shown in the typical connection example below. The ALARM/REMOTE connector is described later. • Refer to the Operating Instructions for each system component for connection and operation.
● Connecting Two or More Data Multiplex Units to System Controller WV-CU360 (Panasonic Secuarity Data Mode) 1 ch 4 ch 5 ch 2 ch 6 ch 3 ch 7 ch VS/VD OUTPUT VS/VD INPUT 8 ch SPOT SW OUT SPOT SW IN Unit Address 2 IN 4 OUT 4 3 2 1 IN IN 2 1 OUT OUT G 3 CAMERA SPOT VS/VD Unit Address 1 A L A R M / R E M OT E SD B A RD B A RS485 IN 4 OUT 4 3 2 1 IN IN 2 1 OUT OUT A L A R M / R E M OT E T G SIGNAL GND DATA MODE MODE 3 CAMERA SPOT VS/VD B R A B RS485 A SIG
● Connecting Two or More Data Multiplex Units to Matrix Switcher WJ-SX350 (Camera Communication Mode) Camera 1 ch 4 ch Camera 5 ch 2 ch 6 ch 3 ch 7 ch 8 ch Camera communication mode 2 Line Data Multiplex Unit WJ-MP204 Unit Address 1 MODE Termination ON IN 4 OUT 4 3 A L A R M / R E M OT E 2 1 IN IN 2 1 OUT OUT T G 3 CAMERA SPOT VS/VD B IN 4 OUT 4 3 2 1 IN IN 2 1 OUT OUT A L A R M / R E M OT E R A B T A G SIGNAL GND DATA RS485 3 CAMERA MODE SPOT VS/VD B R A B
■ Alarm/Remote Connector Alarm-related control signals and remote signals are received via this connector. The table below shows pin assignments of the WJ-MP204. The initial setting is ALARM INPUT. 1. Remove four screws (left x 2, right x 2) on both sides of the WJ-MP204. 2. Remove four screws on the rear panel. 3. Slide the panel cover to the front as viewed from the rear of the WJ-MP204. 4. Remove the connector with cable from CN703 (ALM IN) and attach it to CN702 (ALM OUT).
■ Connector Selection for Setup Menu Output Under the default condition, the setup menu will be output to the devices connected to the SPOT OUT connector and CAMERA OUT connector 1 to 4. When Switch [1] of SW702 in the WJ-MP204 is set to ON, the setup menu will be output only to the devices connected to the SPOT OUT connector. Do not change the positions of Switches 2 to 4 of SW702. Note: Do not set the Switch [2], [3] and [4] of SW702. O.
■ Connection to WV-CU360 ● Basic Connection Connect the DATA port on the Data Multiplex Unit to one of the DATA port on the System Controller with the RS-485 cable. Data Multiplex Unit WJ-MP204 System Controller WV-CU360 DATA DATA RS-485 Cable ● Loop-Through Connection 1. Plug the branch cable (optional accessory) into the DATA port on the Data Multiplex Unit WJ-MP204. 2.
OPERATING PROCEDURES ■ Controlling the Camera Functions with the Data Multiplex Unit WJ-MP204 ■ Controlling the Camera Functions with the System Controller WV-CU360 Before starting operation, loosen the screw on the front cover with a screwdriver. For details, refer to the Operating Instructions for the System Controller WV-CU360. The System Controller WV-CU360 controls the following.
ALARM CONTROL FUNCTIONS ■ Alarm Input ■ Alarm Reset The Data Multiplex Unit processes the following alarms. (As to setting, see page 14, 18 and 19.) ● Mode After Alarm Reset • Camera Site Alarm Alarm multiplexed with video signals from the camera. • Terminal Alarm Alarm received from the ALARM/REMOTE connector. ■ Alarm Operation ALARM MODE set to ON on the Setup menu (See pages 14 and 18 for details.) • Alarm indicator blinks. • Alarm data is transmitted to the system controller and other system units.
SPECIFICATIONS Power Source Power Consumption Camera Input Spot Input VS/VD Input Camera Output Spot Output VS/VD Output Data Communication Standard : 220 - 240 V AC 50 Hz :7W : 1 V[p-p]/75 Ω x 4 : 1 V[p-p]/75 Ω x 1 : VS (1 V[p-p]/75 Ω), VD (4 V[p-p]/75 Ω) x1 : 1 V[p-p]/75 Ω (Looped through) x4 : 1 V[p-p]/75 Ω x1 (Changeable Output from camera input, or Spot input) : VS/VD IN (Looped through), or internal VD (4 V[p-p]/75 Ω) x 1 : Based on RS485 (4-Line/2-Line*1) Modular Jack x 1, or 5 pins terminal x 1*2 :
APPENDIX ■ Operation of Data Multiplex Unit WJ-MP204 versus Operation of System Controller WV-CU360 The functions that can be controlled from both the WJ-MP204 and WV-CU360 in the way of their operation are summarized in the table below. Function Camera Selection WJ-MP204 WV-CU360 Press Enter camera numbers by pressing numeric buttons.
Matsushita Electric Industrial Co., Ltd. Central P.O. Box 288, Osaka 530-91, Japan N1299-1030 2000 © Matsushita Communication Industrial Co., Ltd.
