VP-8-V2 and VP-16-V2 Encoder Quick Start Guide
VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide About this Manual This Manual is applicable to All-in-One NVR (Network Video Recorder). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
VP-8-V2 and VP-16-V2 Series Encoder·Quick Start Guide Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • • • • • • • Ensure unit is installed in a well-ventilated, dust-free environment. Unit is designed for indoor use only. Keep all liquids away from the device. Ensure environmental conditions meet factory specifications. Use the device in conjunction with an UPS if possible.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide Chapter 1 Panel Description 1.1 Front Panel VP-8-V2/VP-16-V2: Figure 1. 1 VP-8-V2/VP-16-V2 Front Panel Table 1. 1 Indicator Description 1 Indicator Description POWER Lights in green when the device is powered on. 2 3 Not Used Tx/Rx 1. Does not light when the network is not connected; 2. Blinks in green when the data is transmitting / receiving; 3. Blinks at higher frequency when the data for transmitting / receiving is larger. 1.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide Table 1.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide Chapter 2 Installation 2.1 Pre-Installation The V2 Series Encoder is advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the Encoder. 1. Keep all liquids away from the Encoder. 2. Install the Encoder in a well-ventilated and dust-free area. 3. Ensure environmental conditions meet factory specifications. 2.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide 2.3 Access to VP-8-V2 and VP-16-V2 ENCODER via Web Browser Steps: 1. Power on the encoder, and connect the encoder to the network. 2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface. The default IP address of the network encoder is 192.0.0.64. You are recommended to change the default IP address after your access. 3. Default username is admin Default password is 12345.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide In the Login dialog box, if you have entered the wrong password for 7 times for the admin user or 5 times for the normal user, the current user account will be locked for 60 seconds. You should download and install the plug-in for the first time to use. Figure 2. 2 Message from Webpage 2.4 Starting Live View 1. In the live view window, select a playing window by clicking the mouse. 2.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide Table 2. 1 Icon Description Icon Description Select the split window mode / Start/Stop live view Capture pictures in live view mode / Manually start/stop recording Enable e-PTZ Previous page Next page / Audio on/off / Start/Stop two-way audio Switch to full-screen live view mode.
VP-8-V2 and VP-16-V2 Series Encoder · Quick Start Guide Figure 2. 4 PTZ Click the zoom/iris/focus buttons to realize lens control. Refer to the following table for description of PTZ control buttons: Table 2. 2 Button Description Button Description Zoom in/out Focus near/far Iris open/close Light on/off Wiper on/off Adjust speed of pan/tilt movement (level 1to 7 is selectable) 1) Alarm. 2) Check the checkbox of Select All and click Copy to copy settings of this day to the whole week.