Operating instructions

How to connect the power cable (AC/DC)
Attach to the DIN rail
Attachintheorderdescribedbelowsothathook(b)ispositionedatthebottom.
1
Hanghook(a)ontheDINrail(
A
).
2
Pull and hold the lever down (
B
).
3
Securehook(b)totheDINrail(
C
).
Hook(a)
A
B
C
Hook(b)
Installing the power supply unit and camera
Important:
● Register the camera to the main monitor station before installation. ( reverse side)
● Do not attach to a ceiling.
● Do not install in areas directly exposed to water or rain.
● Holesmustbemadeinthewallforcablesandwirestopassthrough.Panasonictakesno
responsibility for issues related to opening holes in walls.
● Makesuretowaterprooftheholesmadeinwalls.
● Makesureyouusethesafetywireattachedtothecameratopreventthecamerafrom
falling.
● Requiredpull-outcapacityofasinglescrewis294N{30k
g
f} or more. If this criteria is not
met,makesuretotakeadditionalmeasurestoincreasestrength.
● Do not use an impact driver. (This may lead to damaged screws or over tightening.)
Install the power supply unit
Install the camera (continued)
If connecting an external sensor
Open the cover on the rear and connect the DC cable.
Attachthewallmountbrackettothewallthathasthecableaccessholeand
caulkthebracket.
Pass the DC cable through the recessed area
of the water-resistant rubber and attach the
cable.
2-1 Open the cover. 2-2 Strip the DC cable.
2-3 Remove the water-resistant rubber (A) from the camera and attach it to the DC
cable.
2-4 Loosen the screws (
B) and push in the wires
of the DC cable to the terminal connectors
(non-polar), then tighten the screws.
● Recommendedtorque:
0.8N·m{8.2k
g
f·cm}
● Secure the water-resistant rubber attached to
the cable to its original position.
1-1 Securethewallmountbracket.
Install the camera
1
1-2 Use a water-resistant seal-
anttocaulkaroundthe
bracket,exceptforthebot-
tom part.
● Mountthewallmountbracketsothatthe"
UP"markfacesup,andcaulkasshown
here,makingsuretollinanygaps.
(Ifthebracketisnotproperlywaterproofed,watermayenter,whichmayresultinfire
orelectricshock.)
1-62,4-chome,Minoshima,Hakata-ku,Fukuoka812-8531,Japan
http://www.panasonic.com
©PanasonicSystemNetworksCo.,Ltd.2015
PNQW4921ZA C1015MM0
2
3
12 mm
32 mm
● Insert the wires while pressing the terminal buttons with the tip of a screwdriver.
Connect wires to the external input terminal.
● Refer to "About the external input terminal" on the reverse side and connect the wires
properly.
3-1 Strip the wires.
● Refer to 2-2 of step 2 for stripping wires.
3-2 Remove the water-resistant rubber (
C)
from the camera and attach it to the
wires.
● Refer to the drawing in 2-3 of step 2.
3-3 Connect the wires to the terminals (
D) and reattach
the water-resistant rubber and secure it in its original
position.
4
Closethecover(pushcloseduntilitclicks).
5
● After attaching the 4 screws
(accessory), attach the screw covers.
● Recommendedtorque:
1.2N·m{12.2k
g
f·cm}
Screws
(accessory)
Washer (accessory)
Safety
wire
Screw covers
(accessory)
Mounting screw
(locally procured)
Attachthecameratothewallmountbracketandsecureit.
Adjusting the camera angle.
6
Viewwhenlookingfrombelow
● Recommendedtorqueforscrew
A
,
B
:0.7N·m{7.1k
g
f·cm}
Adjusting angle left and right:
1. Loosen screw A and adjust the
angle left or right.
2. Tighten screw
A.
1. Hold the camera in one hand and
loosen screw
B to adjust the angle up
or down.
2. Tighten screw
B.
Adjusting angle up and down:
Turnonthecamera,monitorthecameraimage,conrmtheviewableareaandthe
camera audio. (
Operating Instructions of the Video Intercom System)
● Ifyou’renotsatisedwiththeviewablearea,adjustthecameraangleandconrmthe
results.
● IftheVideoIntercomSystemincludesasubmonitor,takeittothecamerainstallation
locationandconrmtheimagedisplayedonthesubmonitorwhileadjustingthecamera
angle as necessary.
7
● Attach the safety wire high on the wall so
thatthecameradoesnotstrikeanyonein
the event the camera becomes detached
from the wall.
● Do not hang from the camera.
After you have adjusted the angle,
attach the safety wire to the wall.
8
9
Test the sensor detection and image recording. ( at right)
Lift the tab
to open the
cover
Water-resistant rubber
Cover
It is difficult to tighten the screw when the
camera is facing forward. Using the meth-
od shown to the right, tighten the screw
after rotating the camera body to the left or
right.
When tightening screws
Viewwhenlooking
from below
Loosen this screw
and move the camera
left or right
Screw A
Screw B
When using the heat sensor
Using the sensor range caps Changing the angle of the heat sensor
If there are objects that you do not want the heat sensor to detect, you can limit the detectable
area by attaching the sensor range caps.
You can use the heat sensor adjustment lever on the camera to set the heat sensor to one
of two positions.
■Sensor range cap types and detection range
In addition to the standard cap (already attached to the camera), there are four cap types
(caps 1-4). Each cap prevents a different area from being detected and can be attached
at 45-degree increments. Refer to the following and attach the proper cap at the proper
angle.
● The detection area is an approximation for when the [Heat sensor sensitivity] setting
(
"Changing the sensitivity of the heat sensor", below right) is set to [Normal].
(Varies by ambient temperature at camera installation location)
(Example 1) When there is an object on the right side of
the viewable area that you do not want to
be detected (house next door, street, etc.).
Attach one of caps 1-3 as shown on the right
according to the area you do not want to be
detected.
(Example 2) When there is an object in the top left of
the viewable area that you do not want
to be detected (cars in a street, etc.).
■Removing and attaching sensor range caps
When removing:
Usethethickendofthecapremovementtool(accessory)toremove.
When attaching:
Rotate the tab on the cap toward the
top or at a 45-degree angle according to
the type of cap or direction, and attach
the cap on the camera as shown on the
right.
Attach one of caps 1-3 as shown
above according to the area you
do not want to be detected
① ② ③
When using motion detection
Changing the detection range of the motion detection sensor
Changing the sensitivity of the motion detection sensor
Use the main monitor to change the camera’s [Motion detection range] setting.
● Bysettingtheareasthatyoudonotwantmotiontobedetectedfromthe12blocksshownin
the screen below, you can narrow down the areas that motion can be detected in.
Use the main monitor to change the camera’s [Motion detection sensitivity] setting. (You can
adjust the amount of motion that will be detected by setting the sensitivity setting.)
■ Motion detection sensitivity setting (4 levels)
● High sensitivity
● Normal (default setting)
● Low sensitivity
● Very low sensitivity
Changing the setting (Example: Video Intercom System VL-SWD501 series)
Usethemainmonitorsettings,select[Connecteddevices]→[Camera]→cameranumber
→[Sensorsettings]→[Motiondetectionrange]→theareasnotsubjecttodetectionfrom
the12blocks,andthentouch[Configure].
(Example)Whencheckingmotiondetectionperformance,acarinthestreetthat
you do not want to be detected is displayed in the top of the screen
In the motion detection range screen, select the area containing the street that you do not
want to be detected.
Adjusting sensor sensitivity and detection range
Note:
● When[Highsensitivity]isselected,itismorelikelythatwindorobjectsoutsidethe
viewable area will cause detections. (Use this setting only when the installation
environmentabsolutelyrequiresit)
Use the main monitor to change the camera’s [Heat sensor sensitivity] setting.
( The heat sensor’s range of detection varies by the selected sensitivity. )
■Heat sensor sensitivity and detection range
The detection range shown below is an approximation. (Varies by ambient temperature
and environment of installation location)
High sensitivity:
Low sensitivity:
Normal (default setting):
■Lever position and sensor detection range
The detection range shown below is an approximation. (Varies by ambient temperature
and environment of installation location)
At time of purchase:
When lever is raised:
Changing the sensitivity of the heat sensor
Usethemainmonitorsettings,select[Connecteddevices]→[Camera]→camera
number→[Sensorsettings]→[Heatsensorsensitivity]→thesensitivityfromthe4lev-
els.
Changing the setting (Example: Video Intercom System VL-SWD501 series)
Very low sensitivity:
Ambient temperature: 20 °C
Usethemainmonitorsettings,select[Connecteddevices]→[Camera]→camera
number→[Sensorsettings]→[Motiondetectionsensitivity]→thesensitivityfromthe4
levels.
Changing the setting (Example: Video Intercom System VL-SWD501 series)
Cap type
Approximate detection range (view when looking from above)
20 ºC 0 ºC 30 ºC
Standard (attached
to camera)
Cap 1
(Example) Cap 1 (Example) Cap 1 (Example) Cap 1
Cap 2
(Example) Cap 3 (Example) Cap 3 (Example) Cap 3
Cap 3
When you want
tomakeoneside
not detectable
Cap 4
When you want to
makebothsides
not detectable
● The detection range rotates according to the sensor range cap angle.
Motion will not be detected in areas
withan"X".
Configure
>>>>>>Motion detection range
Touch the areas that you do not
want to detect motion for.
If you want to detect small changes in
motion, select [High sensitivity], and select
[Low sensitivity] or [Very low sensitivity] if you
want to detect only drastic changes in motion.
Detection
range
About 5 m
About 5 m
About 5 m
About 5 m
About 6 m
About 6 m
About 6 m
About 6 m
About 4 m
About 4 m
About 4 m
About 4 m
Detection
range
Example 1
Example 2
Detection
range
Tab
About 6 m
About 5 m
About 4 m
About 3 m
Detection
range
Detection
range
Detection
range
Detection
range
View from above
View from above
View from above
View from above
Lever
At time of purchase:
When the lever is raised:
Viewable area
Detection range
Viewable area
Detection range
Confirming sensor detections
From the top menu of the main monitor, touch → →
[Connecteddevices]→[Camera]→cameranumber→[Sensorsettings]→
[Checksensors]→tapeachtypeofsensortoconfirm.
You must trigger the
sensor at the camera
within about 20 minutes.
To end the operation, press
.
1
2
3
Use the main monitor to confirm the detections made by the heat sensor or motion detection.
● The operations described here are based on the VL-SWD501 series main monitor. See the
Operating Instructions of the Video Intercom System for more information.
● Whensensorsmakeadetection
–
The camera’s LED lights and indicator lamp
ash.
–
The display on the main monitor changes as
shown to the right according to the sensor type
selected in step 1.
Note:
● Thecameraimageturnsoffautomaticallyafterabout20minuteswhenconrmingthesensor.If
20minutespasswhileconrming,startoverfromthebeginning.
● Youcanalsousetheaboveproceduretoconrmacommerciallyavailableexternalsensor,if
connected.
When detections are not made correctly or when incorrect detections are made
■When detections are not made prop-
erly
Refer to "Adjusting sensor sensitivity and
detection range" (
atright)andmake
adjustments as explained below.
Heat sensor:
● Change the [Heat sensor sensitivity]
setting (increase sensitivity)
Motion detection:
● Change the [Motion detection sensitivity]
setting (increase sensitivity)
■ When incorrect detections are made
Refer to "Adjusting sensor sensitivity and
detection range" (
atright)andmake
adjustments as explained below.
Heat sensor:
● Use the sensor range caps
● Change the angle of the heat sensor
● Change the [Heat sensor sensitivity]
setting (decrease sensitivity)
Motion detection:
● Change the [Motion detection sensitivity]
setting (decrease sensitivity)
● Change the [Motion detection range]
setting (change the range)
Testing the sensor detection images
Confirm if images are correctly recorded before and after images are recorded for sensor detections.
● The operations described here are based on the VL-SWD501 series main monitor. See the
Operating Instructions of the Video Intercom System for more information.
From the top menu of the main monitor, touch → →
[Connecteddevices]→[Camera]→cameranumber→[Sensorsettings]→
[Recording test].
You must trigger the
sensor at the camera
within about 20 minutes.
When recording ends, touch [Result] and
confirm the recorded images (A-D).
To end the operation, press
.
● A screen such as the one shown on
the right is displayed on the main
monitor, and images from when the
detection occurred are retained (up
to 4 still images).
● Touch an image (
A
-
D
) to display it full-
screen.
● To perform a recording test again, touch
in the screen shown to the right,
and touch [Test again] when the screen
in step 3 is displayed.
When using default setting:
A:
Image from 1 second before detection
B to D: Images from time of detection
until about 2 seconds after detection
You can use the
[Recording before detection] setting to
retain images from up to 2 seconds before
the detection. (
Operating Instructions
of the Video Intercom System)
The sensor name is displayed for
about 1 second. When the sen-
sor is triggered again, the name is
displayed.
■Confirm with a subject that you want
to detect
Checkwhetherthesensoristriggeredatthe
location where you want to detect movement,
with people moving in the direction you want
to detect.
■Confirm with a subject that you do not
want to detect
Checkwhetherthesensorisnottriggeredby
subjects that you do not want to detect, such
as people or cars moving on a street.
● The camera waits for the sensors to be triggered and live images from the camera are
displayed.
Motion detection:
Heat sensor:
Heat sensor
ヒ
ヒ
Motion detection
Area that motion was detected in (shown in yellow)
Displayed when recording is complete
Live image
(Example) When the heat sensor
makesadetection
ヒ
ヵㄆㄔㄕチ㄂ㄈ㄂ㄊㄏ
ンㄆㄔㄖㄍㄕ
ラㄆ㄂ㄕチㄔㄆㄏㄔㄐㄓ
ヒ
Result
①
②
③
④
1
4
3
1
5
Name of sensor which made the detection
Confirm the displayed message and then touch [Next].
● The camera waits for the sensors to be triggered.
2
■About the installation location
● The device must be installed inside an electrical panel or cabinet.
● Areadilyaccessibledisconnectdeviceshallbeincorporatedexternaltotheequipment.
-Externaldisconnectdevicemustbecertiedandhaveacreepageandclearance
distance of 3 mm or more.
■Precautions for wiring
● Makesureyouturnoffthepoweratthebreakerbeforeperforminganywiringwork.
● Always connect AC or DC cables to the appropriate connection terminals. Incorrectly
connecting the AC or DC cables may damage the power supply unit.
● Topreventthepowercablesfromdisconnectingandtopreventelectricshock,securethe
power cables using the cable binders (accessory) and attach the cable covers.
B
A
D
C
CAUTION
Insert the cables firmly all the
way into the terminals.
If the cables are not inserted all
the way, heat may be generated.
*1Makesurethattherearenobarewires
exposed outside the product.
Connect the power supply unit (accessory) and AC/DC cables (locally procured).
1
Strip the AC/DC cables as follows:
7 mm
45 mm
<AC cable>
<DC cable>
25 mm
7 mm
2
Remove the screws (
B
) and then remove
the cable covers (
A
).
3
Connect the AC/DC cable to the AC IN
terminal/DC OUT terminal on the top and
bottom of the power supply unit, and then
secure the wires by tightening the screws.
● Recommendedtorque:
-ACterminal:0.4N·m{4.1kgf·cm}
-DCterminal:0.45N·m{4.6kgf·cm}
220-240 V AC
AC cable
*1
DC cable
24 V DC
Screws
*1
Cable binders (accessory)
4
Use the cable binders (accessory) to secure
the AC/DC cables (double-coated area) to
the power supply unit.
5
Makesuretoreplacethecablecovers(
A
).
DC OUT terminal
AC cable
binder hole
AC IN terminal
<Top view>
<Bottom view>
DC cable
binder hole
Cable covers (
A
)
Screws (
B
)
Mounting screws
(locally procured) × 4
Vertical, flat wall
46 mm
83.5mm
Cable access
hole
DC cable
Water-
resistant
sealant
Wall mount
bracket
Configure
>>>>>>Motion detection range
Touch the areas that you do not
want to detect motion for.
Thebottompartofthebracket
has a water drain hole on it; do
notcaulkit
Power supply unit (with cable covers
removed)
<Front view>