Wireless Monitor Operating Instructions Model No. VL-W600BX Thank you for purchasing a Panasonic Wireless Monitor. This unit is an accessory unit for Panasonic Wireless Video Intercom System. You must register to the main monitor station before using. Please read these Operating Instructions before using the unit and save for future reference. VL-W600BX̲ZA̲maybe̲E.
Table of Contents Important Information Important safety instructions .............................................................................................................3 Additional safety information .............................................................................................................4 For best performance .........................................................................................................................
Important Information Important safety instructions 1) Read these instructions. All the safety and operating instructions should be read before the appliance is operated. 2) Keep these instructions. The safety and operating instructions should be retained for future reference. 3) Heed all warnings. All warnings on the appliance and in the operating instructions should be adhered to. 4) Follow all instructions. All operating and use instructions should be followed. 5) Do not use this apparatus near water.
Important Information Additional safety information 1. Use only the power source marked on the unit. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. 2. Use only the specified AC adaptor. 3. Do not tamper with the plug. 4. Make sure the plug is securely inserted. 5. Do not touch the plug with wet hands. 6. Do not place objects on the power cable. Install the unit where no one can step or trip on the cord. 7.
Important Information For best performance Before using LIt is prohibited to disassemble or modify this unit. Contact the dealer where you purchased this unit for repair. LWhen power fails, this unit cannot be used. LFor the recorded image: The recorded image may be lost when: – Mishandled – Electric shock or radio wave interference occurs. – The power is turned off during use. (We might not be held responsible for the damage.
Important Information Using near medical equipment LConsult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates in the frequency range of 2.4 GHz to 2.48 GHz, and the power output level can range from 0.03 to 0.175 watts.) Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so.
Preparation Accessory information Included items 1 2 3 4 5 6 7 No. Item Quantity Notes 1 AC adaptor 1 Cord length: Approx. 1.8 m 2 Battery 1 ------ 3 Battery cover 1 ------ 4 Charger 1 ------ 5 Charger stand 1 ------ 6 Wood screws 2 For the charger. (3.5 mm x 18 mm) 7 Washers 2 For the charger. Location of controls N Rear view N Charger LTo assemble the charger stand, see page 11.
Preparation N Front view A Monitor display (page 9) B {DOOR KEY} button LAllows you to open the door when the door opener is connected to the main monitor station (page 28). C {PAGE} button LPress to page the main monitor station or another sub monitor station (page 17, 24). VL-W 600 A N B Dark DOOR K EY DOOR VOLUM E C Bright M CAMER VOICE CH A NGER BRIGHT L S 3 SEC) K J (HOLD ET Default setting u A PAGE D D {BRIGHT/SET} button LPress to adjust the brightness of displayed images.
Preparation N Monitor display The following display is example for description purposes, and it may differ from the actual display. LThe monitor display is turned off during standby. When you press {OFF}, the information display appears. A B C D E F VL-GM002 G H DOOR KEY PAGE DOOR CAMERA VOLUME VOICE CHANGER Navigator key BRIGHT I J CHARGE SET (HOLD SET) OFF {OFF} TALK K A Indicates the battery level. Estimated operating time after charging the battery for 7 hours.
Preparation E Indicates that the door is opened when the door opener is connected to the main monitor station (page 28). K Indicates the operation of the navigator key. (The display varies depending on the operation.) F Indicates the level of the reception. Strong Use within this range. Press {◄}. Press {►}. Weak LWhen the sub monitor station is out of range of the main monitor station, “ ” flashes and “OUT OF RANGE” is displayed. (Move closer to the main monitor station.
Preparation Charging the sub monitor station 1 Insert the battery. A Align the terminals and insert. B A B Close the battery cover. Terminals 2 Assemble the charger stand, and plug the AC adaptor into the power outlet (100 – 240 V AC). N To assemble the charger stand A Plug the connector of the AC adaptor into the jack on the charger. Power outlet (100 – 240 V AC, 50/60 Hz) LYou can pull out the AC adaptor cord to the left or right side. AC adaptor B Attach the charger stand.
Preparation 3 Place the sub monitor station on the charger and charge the battery. (At the first time of charging, it takes about 7 hours to complete charging.) While charging: The CHARGE indicator lights up. When charging is complete: The CHARGE indicator turns off. LLocate the charger where “OUT OF RANGE” is not displayed on the sub monitor station. (The charging time becomes longer where the sub monitor station is out of range of the main monitor station.) Important: LUse only the included AC adaptor.
Preparation Registering the sub monitor station to the main monitor station (REGISTRATION) Place the sub monitor station to be registered near the main monitor station and then operate the sub monitor station within 2 minutes in succession to the operations of the main monitor station. LCharge the sub monitor station to be registered for about 5 minutes before registration (page 11).
Preparation Canceling the registration (CANCELLATION) You can cancel the registration of a sub monitor station if you do not use it. LPlace the sub monitor station to be canceled near the main monitor station and then operate the sub monitor station. LYou can also operate this feature in the same way by using the main monitor station. {D} {SET} {VOICE CHANGER} {▼} {▲} {OFF} 1 During standby, press and hold {SET} for about 3 seconds.
Doorphone Answering a call When you receive a call from a door station, the sub monitor station rings and the TALK indicator flashes. You can monitor the visitor on the monitor display before answering a call. 1 When a ringer tone is heard, press {TALK}. 2 Speak to the visitor. LSpeak alternately with the visitor. (If you and the visitor speak at the same time, you will not hear each other.) NTo adjust the speaker volume: NTo adjust the display brightness: Press {BRIGHT} (page 8).
Doorphone If it is difficult to hear the visitor’s voice due to noise (Press-to-talk mode) You can speak with the visitor alternately by pressing {TALK} to switch between the talking mode and the receiving mode. 1 Press and hold {TALK} for about 2 seconds during a call. LA beep sounds, and “ ” appears on the display. 2 To speak to the visitor: Speak while pressing and holding {TALK}. To hear the visitor: Release {TALK}. Note: LPress-to-talk mode is canceled after the conversation ends.
Doorphone Transferring a call To transfer a call using the sub monitor station: To receive a transferred call using the sub monitor station: 1 During a door call, press {PAGE} and talk to the 1 When the paging call is heard, press {TALK} paged party. and talk to the paging party. LThe image taken by the door station disappears, and the TALK indicator flashes. 2 Tell the paged party to receive the door call. Press {OFF}.
Doorphone Answering another call during a call or while monitoring When receiving another call during a call or while monitoring, the ringer tone is heard while flashing button and display indication notify you which device is calling. *1 *1 or ll Ca Camera 1 – 4*1 Door station 2*1 Door station 1 During a call or while monitoring When the door station is calling: {DOOR} flashes. When the camera is calling: {CAMERA} flashes.
Camera Monitoring the view from the camera (Camera monitor) You can monitor the sound and camera of the place where the camera is located. {CAMERA} {BRIGHT} ▲ { } {▲} {OFF} {TALK} 1 Press {CAMERA}. LThe image taken by the camera will be shown on the display, and you will hear the sound from the camera. (The sound from your end will not be heard at the camera.) LWhen 2 or more cameras are registered, press {CAMERA} repeatedly to select the desired camera.
Camera Answering a call from the camera When the sensor detects motion, the sub monitor station rings and the {CAMERA} button flashes. The image taken by the camera appears on the display. 1 When a ringer tone is heared, press {CAMERA}. LYou will hear the sound from the camera. (The sound from your end will not be heard at the camera.) NTo speak to the other party at the camera: Press {TALK}. Press {BRIGHT} (page 8). 2 To end monitoring or the conversation, press {OFF}.
Recording Recording an image The main monitor station can automatically or manually record (save) up to 100 images from the door station or the camera in total. For more detailed functions, refer to the Operating Instructions included with the main monitor station. Auto recording When you receive a call in standby mode, images are automatically recorded.
Recording Viewing recorded images You can view or delete recorded images, or protect up to 20 images. 1 During standby, press {D} and select the desired item to view ▲ by using { } or {▲}.
Recording Recorded images taken by the door station NWhen “DOOR STATION PICTURE REC NUMBER” is set to “1 PICTURE” (Refer to the Operating Instructions included with the main monitor station) (default setting): NWhen “DOOR STATION PICTURE REC NUMBER” is set to “4 PICTURES” (Refer to the Operating Instructions included with the main monitor station): 1st image*1 4 images per set Recording device (page 9) 2nd image*2 3rd image*2 4th image*2 Recording number (1 – 100) ● Recording date and time : Unview
Intercom Making an intercom call from the sub monitor station To call from the sub monitor station: To answer an intercom call: 1 Press {PAGE} and talk to the paged party. 1 When the paging call is heard, press {TALK}. LThe TALK indicator lights up. 2 When the paged party answers the call, talk with 2 Talk with the other party. 3 To end the intercom call, press {OFF}. 3 To end the intercom call, press {OFF}. the paged party. Note: LAn intercom call will automatically end in about 90 seconds.
Programming Changing the function settings (Function list) Changing the settings You can change and set the functions of “SUB” and “CAM”. LWhen receiving a call while setting or no operation is done for about 90 seconds, the setting function screen automatically quits. {▼} {▲} {D} {OFF} {SET} 1 During standby, press and hold {SET} for about 3 seconds. 2 Select the desired item to change the settings by pressing {▼} or {▲}, and press {D}.
Programming Functions of the sub monitor station The functions listed below can be set when selecting “SUB” in step 2 on page 25. The default setting is indicated in bolds. Functions Contents VOICE ANSWER You can answer a call from the door station, the main monitor station or the sub monitor station by answering with a clear voice such as “Yes” or “Hello” unless you press {TALK}. (This function is not work for the calls from the camera.) ON, OFF LTo answer a call by voice, see page 15.
Programming Functions of the camera The functions listed below can be set when selecting “CAM” in step 2 on page 25. You can set the functions of the camera 1 – 4 separately. The default setting is indicated in bolds. Functions Contents CAM RINGER You can select the ringer pattern that is heard from the camera when the sensor detects motion. TONE A, TONE B, TONE C, TONE D LTo confirm the ringer pattern, press {►} while selecting the desired tone.
Programming Adjusting the volume Ringer volume You can change the volume of the ringer heard when receiving calls from the door station or the camera. NTo adjust the ringer volume of the door station: During standby, press {▼} or {▲}. Each time you press {▼}, the volume level decreases. Each time you press {▲}, the volume level increases. LIf you press and hold {▼} until 2 short beeps sound, the ringer volume is set to “OFF”. NTo adjust the ringer volume of the camera: During standby, press {◄} or {►}.
Help Cleaning Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a slightly damp cloth. Important: LWhen cleaning this unit, disconnect the AC adaptor from the power outlet. LDo not use anything containing alcohol, polish powder, powder soap, benzine, thinner, wax, petroleum, or boiling water. Also do not spray with insecticide, glass cleaner, or hair spray. This could cause a change in color or quality.
General Information Technical data about this product Sub monitor station (VL-W600BX) Power supply: Dimensions: Mass (Weight): Operating environment: External material: Frequency: Ni-MH battery (3.6 V DC / 650 mAh) Approx. height 157 mm x width 52 mm x depth 35 mm Approx. 175 g 0 °C to 40 °C, Up to 90% RH (Relative Humidity) non condensing ABS resin 2.402 GHz – 2.
Notes 31 VL-W600BX̲ZA̲maybe̲E.
For your future reference Date of purchase Serial number (found in the battery compartment of the unit) Dealer’s name and address Dealer’s telephone number Attach your sales receipt here. Panasonic Communications Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Copyright: ● This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only.
