OPERATING INSTRUCTIONS TX-43LX650B / TX-43LX650BZ / TX-43LX660B TX-50LX650B / TX-50LX650BZ / TX-50LX660B TX-55LX650B / TX-55LX650BZ / TX-55LX660B TX-65LX650B / TX-65LX650BZ / TX-65LX660B LED TV e-MANUAL You can find instructions for your TV’s features in the E-Manual. To access the E-Manual, enter Settings menu, select Manuals and press OK. For quick access press Home/Menu button and then Info button.
IMPORTANT - Please read these instructions fully before installing or operating.................................. 2 Video................................................................31 Audio................................................................32 Picture..............................................................34 Subtitle.............................................................34 Supported DVI Resolutions.................................. 35 Markings on the Product....................
Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains. The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable.
Hazardous Live Terminal: The marked terminal(s) is/are hazardous live under normal operating conditions. i Caution, See Operating Instructions: The marked area(s) contain(s) user replaceable coin or button cell batteries. CLASS 1 LASER PRODUCT Class 1 Laser Product: This product contains Class 1 laser source that is safe under reasonably foreseeable conditions of operation.
Maintenance First, remove the mains plug from the mains socket. Display panel, Cabinet, Pedestal Assembling / Removing the pedestal Preparations Take out the pedestal(s) and the TV from the packing case and put the TV onto a work table with the screen panel down on the clean and soft cloth (blanket, etc.) Regular care: Gently wipe the surface of the display panel, cabinet, or pedestal by using a soft cloth to remove dirt or fingerprints. For stubborn dirt: 1. First clean the dust from the surface. 2.
3. Insert the screws (M4 x 12) provided and tighten them gently until the stand is properly fitted. 43” 50/55/65” When using the wallhanging bracket Please contact your local Panasonic dealer to purchase the recommended wall-hanging bracket. Holes for wall-hanging bracket installation; Rear of the TV x4 x6 M4 x 12 mm M4 x 12 mm a b M6 x 20 mm Removing the pedestal from the TV Be sure to remove the pedestal in the following way when using the wall-hanging bracket or repacking the TV.
High Dynamic Range (HDR) / Hybrid LogGamma (HLG) Introduction Thank you for choosing our product. You’ll soon be enjoying your new TV. Please read these instructions carefully. They contain important information which will help you get the best from your TV and ensure safe and correct installation and operation.
Antenna Connection Connect the aerial or cable TV plug to the AERIAL INPUT (ANT) socket located on the left side of the TV or satellite plug to the SATELLITE INPUT (LNB) socket located on the rear side of the TV. Left side of the TV ANT Rear side of the TV LNB If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.
Other Connections If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.
Turning On/Off the TV Connect power IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Plug the power cord to the mains socket outlet. The TV will switch on automatically. To switch on the TV from standby If the TV is in standby mode the standby LED lights up. To switch on the TV from standby mode either: • Press the Standby button on the remote control.
Remote Control 1. 2. 3. 28 27 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Note: Other Panasonic devices cannot be operated with this remote. Inserting the Batteries into the Remote The remote may have a screw that secures the battery compartment cover onto the remote control (or this may be in a separate bag). Remove the screw, if the cover is screwed on previously. Then remove the battery compartment cover to reveal the battery compartment. Insert two 1.5V - size AAA batteries.
network and press OK if you want to use wireless connection instead of wired connection. Initial Setup Wizard Note: Follow the on-screen instructions to complete the initial setup process. Use the directional buttons and the OK button on the remote to select, set, confirm and proceed. When turned on for the first time, a welcome screen will be displayed. Select your language and press OK. Follow the on-screen instructions to setup your TV and install channels.
OK on the remote to confirm and proceed. You can also view Terms of Service, Privacy Policy and Play Terms of Service on this screen. To display the content an internet connection is needed. A message will be displayed mentioning the web site address on which this information can also be viewed, in case internet access is not available. 10. Google Services Select each to learn more about each service, such as how to turn it on or off later. Data will be used according to Google’s Privacy Policy.
be displayed next. Scan Mode, Frequency (KHz), Modulation, Symbol Rate (Ksym/s), Network ID options may need to be set. To perform a full scan set the Scan Mode as Full or Advanced if available. Depending on the selected operator and/or Scan Mode some options may not be available to be set. (Ksym/s) and Polarisation parameters under the Transponder option accurately. Note: If the country selected does not have analogue broadcasts, analogue channels may not be searched.
Home Screen To enjoy the benefits of your Android TV, your TV must be connected to the Internet. Connect the TV to a home network with a high-speed Internet connection. You can connect your TV wirelessly or wired to your modem/router. Refer to the Network & Internet and Connecting to the Internet sections for further information on how to connect your TV to the Internet. The Home menu is the centre of your TV.
Picture off: Select this option and press OK to turn the screen off. Press a button on the remote or on the TV to turn the screen on again. Note that you can not turn the screen on via the Volume +/-, Mute and Standby buttons. These buttons will function normally. Switch Off Timer: Define a time after which you want your TV to switch off automatically. Set as Off to disable. No Signal Auto Power Off: Set the behaviour of the TV, when no signal is detected from the currently set input source.
BISS Key: “Click To Add Biss Key” message will be displayed. Press OK button to add a biss key. Frequency, Symbol Rate (KSym/s), Polarisation, Programme ID and CW Key parameters will be available to be set. Once you are done with the settings highlight Save Key and press OK to save and add the biss key. This option will not be available if the input source is not set as Satellite. Available options will differ depending on the selected country during the initial setup process.
second channel. When the second channel is selected, you can press the Blue button and the first selected channel will be moved to the position of that channel. You can press the Yellow button and enter the number of the channel you want to select. Then highlight OK and press OK to go to that channel. You may need to set the LCN option to Off in order to enable this feature. Channel Edit: Edit channels in the channel list.
and correct satellite and press the Back/Return button to return to the satellite selection screen. Highlight Next and press OK to proceed with the SatcoDX channel list installation. If the selected satellite is not correct for SatcoDX installation, a warning dialogue will be displayed on the screen. The satellite/s that can be selected will be listed. Press OK to close the dialogue and press Back/Return to return to satellite selection screen. Then set the satellite accordingly.
Change PIN: Change the PIN you defined during the initial setup. Highlight this option and press OK. You will need to enter the current PIN first. Then new PIN entry screen will be displayed. Enter the new PIN twice for confirmation. Open Source Licences Display Open Source Software licence information. Accounts & Sign In Highlight this option and press OK to sign into your Google account. Following options will be available if you have signed into your Google account.
power off timer to be set, set as Off to disable. If set as Once the TV will turn off only once at the defined time in Auto Power Off Time option below. Auto Backlight: Set your auto backlight preference. Off, Low, Middle and Eco options will be available. Set as Off to disable. Auto Power Off Time: Available if the Power Off Time Type is enabled. Set the desired time for your TV to go to standby using the directional buttons and press OK to save the new set time.
your Local Contrast Control preference as Low, Medium, High or turn it off by setting as Off. available. This item will not be available, if the input source is not set as HDMI. Flesh Tone: Adjusts the skin tone brightness. Set your preference as Low, Medium, or High to enable. Set as Off to disable. Low Blue Light: Electronic device screens emit blue light that can cause eye strain and may lead to eye problems over time. To reduce the effect of blue light set your preference as Low, Middle, or High.
Digital Output: Set the digital sound output preference. Auto, Bypass, PCM, Dolby Digital Plus and Dolby Digital options will be available. Highlight the option you prefer and press OK to set. Digital Output Delay: Adjust the digital output delay value. Auto Volume Control: With Auto Volume Control, you can set the TV to automatically level out sudden volume differences. Typically at the beginning of adverts or when you are switching channels. Turn this option on/off by pressing OK.
Google Assistant: Highlight On and press OK to turn this feature on or off. Select your active account, view permissions, select which apps to include in search results, activate safe search filter and offensive word blocking, view open source licences. Chromecast Built-in: Set your remote control notification preference. Highlight Let others control your cast media and press OK. Always, While Casting and Never options will be available.
change depending on the selected option. Follow the instructions on the screen for current button functions. Editing the Channels and the Channel List You can edit the channels and the channel list using the Channel Skip, Channel Swap, Channel Move, Channel Edit and Channel Delete options under the Settings>Channel>Channels menu. You can access the Settings menu from the Home Screen or from the TV options menu in Live TV mode.
You might be able to connect your TV to a network wall socket depending on your network’s configuration. In that case, you can connect your TV directly to the network using an Ethernet cable. 1 Then highlight the Sign in to Wi-Fi network notification and press OK. Enter your credentials to log in. A Wireless-N router (IEEE 802.11a/b/g/n/ac) with simultaneous 2.4 and 5 GHz bands is designed to increase bandwidth.
the TV. Additionally you can switch the viewing style by selecting either Normal Parser or Recursive Parser. In Normal Parser mode the files will be displayed with folders if any available. So only the selected type of media files in the root folder or in the selected folder will be displayed. If there isn’t any media files of the selected type, the folder will be assumed as empty.
Press the Menu button to see available options while playing back or displaying media files. The content of this menu differs depending on the media file type. Pause/Play: Pause and resume the playback or the slide show. Repeat: Set the repeat option. Highlight an option and press OK to change the setting. If Repeat One option is selected the current media file will be repeatedly played back or displayed.
Make sure that all CEC settings are properly set up on the connected CEC device. The CEC functionality has different names on different brands. CEC function might not work with all devices. If you connect a device with HDMI CEC support to your TV, the related HDMI input source will be renamed with the connected device’s name. To operate the connected CEC device, select the related HDMI input source from the Inputs menu on the Home Screen.
Accessible TV Guide HBBTV System HbbTV (Hybrid Broadcast Broadband TV) is a standard that seamlessly combines TV services delivered via broadcast with services delivered via broadband and also enables access to the Internet only services for consumers using connected TVs and set-top boxes.
No sound / poor sound Troubleshooting & Tips • Make sure that the sound settings are correctly set. TV does not switch on • Make sure the power cord is plugged in securely to the power outlet. • Disconnect the power cord from the power outlet. Wait for one minute then reconnect it. • Press the Standby/On button on the TV. TV does not respond to the remote control • The TV requires some time to start up. During this time, the TV does not respond to the remote control or TV controls.
Supported File Formats for USB Mode Video Video Codec Resolution Bit Rate Profile VP9 4096x2176@60fps 100Mbps Profile 0/2, Level 5.1 HEVC/H.265 4096x2176@60fps 100Mbps Main/Main10 Profile, High Tier @Level 5.1 MPEG1/2 1920x1080@120fps 80Mbps MPEG4 1920x1080@120fps 40Mbps Sorenson H.263 1920x1080@120fps 40Mbps H.263 1920x1080@120fps 40Mbps H.
Audio Audio Codec Sample rate Channel Bit Rate Container MP3 (.mp3), AVI (.avi), ASF (.asf), WMV (.wmv), DivX (.divx), MKV (.mkv, .mka), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), FLV (.flv), WAV (.wav), OGM (.ogm) MP3 (.mp3), AVI (.avi), ASF (.asf), WMV (.wmv), DivX (.divx), MKV (.mkv, .mka), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .
Audio Codec VORBIS Sample rate Up to 48KHz Channel Bit Rate Container MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), Ogg (.ogg), WMV (.wmv), ASF (.asf), AVI (.avi) Up to 2 < 1.5Mbps (Pure DTS core) MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WAV (.wav), MKV (.mkv, .mka), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), AVI (.avi), OGM (.ogm), DTS (.dts) DTS Up to 48KHz Up to 5.1 DTS LBR 12KHz, 22KHz, 24KHz, 44.
Picture Image Resolution (width x height) Photo Base-line Progressive Non-Interlace Interface JPEG PNG 15360 x 8640 1024 x 768 9600 x 6400 1200 x 800 9600 x 6400 6400 x 4800 3840 x 2160 4000 x 3000 BMP GIF WebP HEIF Subtitle Internal File Extension Container ts, trp, tp TS mp4 MP4 mkv MKV Subtitle Codec DVB Subtitle Teletext CC(EIA608) PGS VobSub PGS TX3G ASS SSA SRT VobSub PGS External File Extension Subtitle Parser .srt SubRip .ssa/.ass SubStation Alpha Advanced SubStation Alpha .
Supported DVI Resolutions When connecting devices to your TV’s connectors by using a DVI converter cable (DVI to HDMI cable - not supplied), you can refer to the following resolution information.
Specification TV Broadcasting PAL BG/I/DK SECAM BG/DK Receiving Channels VHF (BAND I/III) - UHF (BAND U) - HYPERBAND Digital Reception Fully integrated digital terrestrial-cable-satellite TV (DVB-T-C-S) (DVB-T2, DVB-S2 compliant) Number of Preset Channels 12 200 Channel Indicator On Screen Display RF Aerial Input 75 Ohm (unbalanced) Operating Voltage 220-240V AC, 50Hz. Audio Dolby Atmos Headphone 3.
Wireless LAN Transmitter Specifications Frequency Ranges Max Output Power 2400 - 2483.5 MHz (CH1 - CH13) < 100 mW 5150 - 5250 MHz (CH36 - CH48) < 200 mW 5250 - 5350 MHz (CH52 - CH64) < 200 mW 5470 - 5725 MHz (CH100 - CH140) < 200 mW Country Restrictions The Wireless LAN equipment is intended for home and office use in the UK & Ireland (and other countries following the relevant EU and/or UK directive) without any limitation except for the countries mentioned below.
Licences The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste.
Sales and Support Information Customer Communication Centre • For customers within the UK: 0344 844 3899 • For customers within Ireland: 01289 8333 • Monday - Friday 9:00am - 5:00pm, (Excluding public holidays). • For further support on your product, please visit our website: www.panasonic.co.
Important Instruction For your own safety read following instruction carefully before attempting to connect this unit to the mains supply. MAINS (AC) OPERATION The wires in the mains lead are coloured in accordance with the following code : 1 4 2 3 1. Green&Yellow (Earth) (if there is earth cable) 2. Blue (Neutral) 3. Brown (Live) 4.
