Model No. TH-65PB1E TH-65PB1EK Operating Instructions Display Operations Interactive Plasma Display English Please read these instructions before operating your set and retain them for future reference.
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.
Important Safety Notice WARNING 1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping or splashing. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) No naked flame sources, such as lighted candles, should be placed on / above the set. 2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety Precautions WARNING Setup This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Pedestal ......................................................................... TY-ST65P20 • Mobile stand for Display .................................................
Safety Precautions When using the Plasma Display The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display. Do not stick any foreign objects into the Plasma Display. • Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause fire or electric shock.
Safety Precautions CAUTION When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. • Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result. Be sure to disconnect all cables before moving the Plasma Display.
Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully. Use for commercial applications and public viewing Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user.
Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Accessories Accessories Supply Check that you have the accessories and items shown Operating Instruction book Software DVD-ROM × 1 Remote Control Batteries for the Remote Transmitter Control Transmitter N2QAYB000691 (R6 (UM3) Size × 2) • elite Panaboard software • elite Panaboard book • Operating Instructions Display Operations Network Operations Electronic Pen Operations • Software license statements GNU GENERAL PUBLIC LICENSE GNU LESSER GENERAL PUBLIC LICENSE Power supply cord Clamper × 1 TMME289 Fer
Connections Speaker connection Note: Please use 8 Ω/10 W speaker. 2 1 Red Red Black Black While pressing the lever, insert the core wire. Return the lever. AC cord connection and fixing, cable fixing AC cord fixing Unplug the AC cord Plug the AC cord into the display unit. Plug the AC cord until it clicks. Note: Make sure that the AC cord is locked on both the left and right sides. Unplug the AC cord pressing the two knobs.
Connections Video equipment connection Terminals are on the bottom side of the Plasma Display. SERIAL: Control the Plasma Display by connecting to PC (see page 14) 3D IR TRANSMITTER: Connect the 3D IR TRANSMITTER (optional accessory). (8Ω,20W[10W+10W]) SLOT: Terminal board (optional accessories) insert slot Note: (see page 4) The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot.
Connections HDMI connection [Pin assignments and signal names] Signal name Pin No. 1 2 3 4 5 6 7 8 9 10 T.M.D.S Data2+ (8Ω,20W[10W+10W]) Pin No. Signal name T.M.D.S Clock 11 Shield T.M.D.S Data2 Shield T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1 Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0 Shield T.M.D.S Data0T.M.D.S Clock+ 12 T.M.D.S Clock- 13 CEC 14 Reserved (N.C.
Connections PC Input Terminals connection Shared with DVI-D IN. (8Ω,20W[10W+10W]) COMPUTER Conversion adapter (if necessary) (Female) Mini D-sub 15p RGB PC cable (Male) Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. Notes: • With regard to the typical PC input signals that are described in the applicable input signals list (see page 64), adjustment values such as for the standard picture positions and sizes have already been stored in this unit.
Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to “RS-232C”.
Power On / Off Connecting the AC cord plug to the Plasma Display. Connecting the plug to the Wall Outlet Notes: • Main plug types vary between countries. The power plug shown at right may, therefore, not be the type fitted to your set. • When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. INPUT MENU -/ VOL +/ ENTER/ Power Indicator Press the Power switch on the Plasma Display to turn the set on: Power-On.
Power On / Off When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the items with the remote control. Unit buttons are invalid.
Selecting the input signal Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. Input signals will change as follows: PC NETWORK VIDEO COMPONENT* HDMI DVI PC: PC input terminal in PC IN. NETWORK: Network input terminal in LAN or WIRELESS MODULE. VIDEO: Video input terminal in AV IN (VIDEO). COMPONENT*: Component or RGB input terminal in COMPONENT/RGB IN. HDMI: HDMI input terminal in AV IN (HDMI). DVI: DVI input terminal in DVI-D IN.
Basic Controls Main Unit Remote control sensor Volume Adjustment Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” : press to move the cursor down (see page 24) INPUT MENU -/ Main Power On / Off Switch Power Indicator The Power Indicator will light. • Power-OFF .... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) • Standby ........
Basic Controls Remote Control Transmitter ACTION button Press to make selections. ASPECT button Press to adjust the aspect. (see page 20) Standby (ON / OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 15). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. POS.
ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law.
Digital Zoom This displays an enlargement of the designated part of the displayed image. 1 Display the operation guide. Exit Press to access Digital Zoom. The operation guide will be displayed. 1 During Digital Zoom, only the following buttons can be operated. [Remote control] OFF TIMER button [Unit] VOL button INPUT MENU -/ VOL +/ ENTER/ MUTE button VOL button POSITION / ACTION button 2 Select the area of the image to be enlarged. Press on the enlargement location to select.
Viewing 3D images You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear (optional). Note: You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display. For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear. This display supports “Frame Sequential*1”, “Side by Side*2” and “Top and Bottom*3” 3D formats.
Viewing 3D images Troubleshooting for 3D Eyewear Symptoms Checks Cannot see 3D images 3D Eyewear is turned off automatically There is something wrong with the 3D images • Has the 3D Eyewear been switched On? • Ensure that “3D Function” in “3D Settings” is set to “On”. (see page 37) • Some 3D image signals may not be automatically recognized as 3D images. Set “3D Picture Format” in “3D Settings” to match the picture format. (see page 37) • Check if 3D IR TRANSMITTER is turned on and corrected properly.
On-Screen Menu Displays Remote Control Unit 1 Display the menu screen. Press several times. MENU Press to select. (Example: Picture menu) 2 Select the item. Select. Picture Normalise Each time the MENU button is pressed, the menu screen will switch. Normal Viewing Picture Sound Pos./Size Setup Select. Press. Normal Normal Picture Mode Contrast Brightness Colour Hue Sharpness White balance Advanced settings 25 0 0 0 5 Normal Memory save Memory load Memory edit (Example: Picture menu) 3 Set.
Adjusting Pos./Size 1 Press to display the Pos./Size menu. 2 Press to select the menu to adjust. 3 Press to adjust the menu. 4 Press to exit from adjust mode. Pos./Size Normalise Auto Setup H-Pos H-Size V-Pos V-Size Dot Clock Clock Phase Clamp Position 1:1 Pixel Mode Normal 0 0 0 0 0 0 0 Off Note: Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode.
Adjusting Pos./Size Notes: • If the dot clock frequency of an analog signal is 162 MHz or higher, “Dot Clock” and “Clock Phase” cannot be automatically corrected. • When digital signal input, Dot Clock and Clock Phase cannot be made. • Auto Setup may not work when a cropped or dark image is input. In such case, switch to a bright image with borders and other objects are clearly shown, and then try auto setup again. • Depending on the signal, out of alignment may occur after Auto Setup.
Adjusting Pos./Size Clamp Position (During Component/PC input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green. Optimum value for Clamp Position adjustment When black parts have no detail due to underexposure (blackout) → Value that causes least blackout is the optimum. When black parts are tinged with green → Value that cancels the greenishness without causing blackout is the optimum.
Picture Adjustments 1 Press to display the Picture menu. 2 Select to adjust each item. Press to select the menu to adjust. Select the desired level by looking at the picture behind the menu. Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting. Picture Normalise Press “ ” or “ ” button to switch between modes.
Picture Adjustments Item Contrast Brightness Colour Hue Sharpness Effect Less Adjustments More Darker Brighter Less More Reddish Greenish Less More Selects the proper brightness and density for the room. Adjusts for easier viewing of dark pictures such as night scenes and black hair. Adjusts colour saturation. Notes: • You can change the level of each function (Contrast, Brightness, Colour, Hue, Sharpness) for each Picture Mode.
Picture Profiles Up to 8 combinations of picture adjustment values (in the Picture menu and Advanced settings) can be stored in the display memory as profiles and applied as needed, for a convenient way to enjoy your preferred picture settings.
Picture Profiles Saving profiles Follow these steps to save picture adjustment values as profiles. Note: When the settings are locked in “Extended life settings”, profiles cannot be saved. 1 Specify the picture quality in the Picture menu and Advanced settings. (see page 28, 29) 2 In the Picture menu, select “Memory save”. 3 5 1 select Memory save Memory load Memory edit 2 access A N a n 0 ! _ Select a profile name for saving the picture adjustment values. 1 select Memory save 1. [ 2. [ 3. [ 4.
Picture Profiles Loading profiles Load profiles and apply the picture adjustment values to the display as follows. Notes: • Loaded profiles are stored in memory according to the selected input terminal. (see page 17) • When the settings are locked in “Extended life settings”, profiles cannot be loaded. 1 In the Picture menu, select “Memory load”. 1 select Memory save Memory load Memory edit 2 Select the profile to load. 2 access 1. [ 2. [ 3. [ 4.
Sound Adjustment 1 Normalise 2 Select to adjust each item. Press to select the menu to adjust. Select the desired level by listening to the sound. 3 1/2 Sound Press to display the Sound menu. Normal Sound Mode Bass Mid Treble Balance Surround Normal 0 0 0 0 Off Press to exit from adjust mode. Item Sound Mode Bass Mid Treble Balance Surround Details Normal: Emits the original sound. Dynamic: Accentuates sharp sound. Clear: Attenuates human voice. Adjusts low pitch sounds. Adjusts normal sounds.
Setup menu 1 Press to display the Setup menu. 2 Press to select the menu to adjust. 3 Press to adjust the menu. 4 Press to exit from adjust mode. Press Setup 1/2 Touch-Pen Mode 3D Settings Signal Screensaver Extended life settings ECO Mode settings Input label Function Button Settings Component/RGB-in select No activity power off Menu Display Duration OSD Brightness OSD Language RGB Disable 30 S 5 English (UK) to return to the previous menu.
Day/Time Setup / On/Off Timer Setup The timer can switch the Plasma Display On or Off. Before attempting Timer Set, confirm the Time and adjust if necessary. Then set POWER ON Time / POWER OFF Time. 1 2 Setup Press to display the Setup menu. Press to select On/Off Timer Setup or Day/Time Setup. Press to display the On/Off Timer Setup screen or Day/Time Setup screen.
Touch-Pen Mode Set Touch Pen mode. Select “Touch-Pen Mode” in “Setup” menu and press Touch-Pen Mode SLOT INPUT HDMI DVI PC NETWORK Off Off Off Off Off button. “SLOT INPUT” is displayed when an optional Terminal Board is installed. When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed. Set “On” or “Off” for each input terminal. If you switch to the input terminal that is set to “On”, the mode becomes Touch Pen Touch-Pen On mode.
3D Settings To view the 3D images, please adjust and setup the 3D settings. Note: Set these settings for each input terminals. Select “3D Settings” in “Setup” menu and press button. 3D Settings sub-menu screen 3D Settings 3D Function 3D Picture Format 3D Picture Sequence Safety Precautions On Auto Normal • 3D Function On Off On: To view the 3D images, please set it to “On”. You can see 3D images for 3D image signal and 2D images for 2D image signal. Off: You can see 2D images instead of 3D images.
Screensaver (For preventing image retention) Do not display a still picture, especially in 4:3 mode, for any length of time. If the display must remain on, a Screensaver should be used. 1 Select “Screensaver” in “Setup” menu and press 2 Function selection button. Screensaver Time Press to select Function. Press to select the desired function.
Screensaver (For preventing image retention) Setup of Screensaver Time After selecting Time Designation, Interval or Standby after SCR Saver, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when “Mode” is “On” or “Off”.) Press to select Start Time / Finish Time (when Time Designation is selected). Press to select Periodic Time / Operating Time (when Interval is selected).
Reduces screen image retention Extended life settings The following settings are setup to reduce image retention: Select “Extended life settings” in “Setup” menu and press button.
Reduces screen image retention NANODRIFT Saver Moves the display position of the screen slightly to reduce image retention on the display panel. Low–High: NANODRIFT Saver operates. The display position of the screen moves at set time intervals. You can set the screen movement range. Some of the screen may appear to be missing as a result of this operation. If you change the value, a mask is displayed in the range where the picture is missing as a result of position movement.
Reduces screen image retention Custom settings Set the individual “Image Retention Reduction” menu. 1 Select “Custom settings”. Extended life settings Express settings Custom settings Reset 1 select 2 access set each menu to the recommended setting: 2 To Select “Recommended settings”.
ECO Mode settings Select “ECO Mode settings” in “Setup” menu and press button. ECO Mode settings ECO Mode Power save Standby save PC Power management DVI-D Power management No signal power off Custom Off On 1 select 2 adjust Off Off Disable ECO Mode Custom: The menu of power consumption reduction is individually set. On: The following fixed values are set to the menu of power consumption reduction. Individual setting is not available.
Customizing the Input labels This function can change the label of the Input signal to be displayed. (see page 17) Select “Input label” in “Setup” menu and press button.
Function Button Settings Set the functions that operates when is pressed. Function Button Settings Select “Function Button Settings” in “Setup” menu and press button. • Function Button 1, Function Button 2 The following functions are set to the FUNCTION button. Function Button 1 Function Button 2 Function Button Guide Touch-Pen Scrolling bar On Note: Factory settings are as follows.
No activity power off Disable Enable When this function is set to “Enable”, the power is turned off (standby) automatically when there is no operation of the Plasma Display for 4 hours. Starting from 3 minutes before the turn off, the remaining time will be displayed. Press any key to abort. No activity power off 3min When the power is turned off due to this function, a message “Last turn off due to ’No activity power off’.” is displayed next time the power is turned on.
Setup for MULTI DISPLAY By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all screens. For this mode of operation, each plasma display has to be set up with a Display number to determine its location. Notes: • During Touch Pen mode, “MULTI DISPLAY Setup” becomes “Off” and this function cannot be used. • During Multi display, the 3D images are displayed as 2D images.
Setup for MULTI DISPLAY Item Details Reduces the peak of brightness for each display to enable as uniform display as possible. Select “Off” or “On”. The brightness depends on each display’s setting. The brightness difference is minimized. Off On Video Wall Uniformity Note: If you set Video Wall Uniformity to On, the following menus will be unavailable and these settings will be fixed to the initial values.
Setup for Portrait Divide an input image into 3 parts, and display one of them to a plasma display which is set vertically. The image will be enlarged 3 times and rotated 90-degree. (Example) Notes: • During Touch Pen mode, “Portrait Setup” becomes “Off” and this function cannot be used. • When using the Portrait function with displays set vertically, “Display orientation” in Setup menu has to be set to “Portrait” (see page 46).
Setup for Portrait 4 Viewing Area / Location Viewing Area: Set a mode of image division for Portrait function. Location: Set a location of image to be displayed for Portrait function. Press to select Viewing Area or Location. Press to select each functions. Portrait Setup Portrait Setup Seam hides video Viewing Area Location Video Wall Uniformity Notes: • For HD signal videos, the “Viewing Area” is set at “16:9”, and cannot be changed.
Setup for Input Signals Component / RGB-in select Component RGB Select to match the signals from the source connected to the Component / RGB or PC input terminals. Y, PB, PR signals “Component” RGB signals “RGB” Note: Make setting of the selected input terminal (COMPONENT/RGB IN or PC IN). YUV / RGB-in select YUV RGB Select to match the signals from the source connected to the DVI input terminals.
Setup for Input Signals Signal menu Note: “Signal” setup menu displays a different setting condition for each input signal. Select “Signal” in “Setup” menu and press For Video (S VIDEO) For RGB [ AV ] Signal 3D Y/C Filter (NTSC) Colour system Cinema reality Noise reduction On Auto Off Off [ RGB ] Signal Sync Cinema reality XGA Mode Noise reduction H-Freq. V-Freq. Signal Format For Component [ Component ] Signal button. Auto Off Auto Off 63.98 kHz 60.
Setup for Input Signals • Sync This function operates only during input from PC IN terminal. Setting RGB sync signal Confirm that the input is set to RGB input (this setting is valid only for RGB input signal). Auto: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync. on G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
Setup for Input Signals • Noise reduction Sets the following three NR (Noise Reduction) functions together. P-NR, Mosquito NR, Block NR ( Press to select “Noise reduction”. ) Noise reduction Off Press to select “Off”, “Min” , “Mid” , “Max” , “Advanced”. Advanced NR Sets the three NR functions separately. 1 Press to enter Advanced NR. 2 Noise reduction Press to select “Advanced”. Press to select P-NR, Mosquito NR or Block NR. Press to select “Off”, “Min”, “Mid”, “Max”.
Options Adjustments Options 1 Press to display the Setup menu. Weekly Command Timer Audio input select Input Search Press to select “OSD Language”. 2 Onscreen display Initial input Initial VOL level Maximum VOL level Input lock Button lock Remocon User level Press for more than 3 seconds. Press to select “Options”. 3 Options Shipping Press to display the Options menu. Press to select your preferred menu. 4 Press to adjust the menu.
Options Adjustments Item Adjustments Input lock Locks the input switch operation. Off SLOT INPUT*1 VIDEO COMPONENT*2 HDMI DVI PC NETWORK *1 “SLOT INPUT” is displayed when an optional Terminal Board is installed. When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed. *2 “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”. (see page 51) Notes: • Only the adjusted signal is displayed (see page 17).
Options Adjustments Item Adjustments Studio W/B Off: Nullify all the settings adjusted. On: Sets the colour temperature for TV studio. Note: Valid only when the “Warm” is set as “White balance” in Picture menu. Studio Gain Sharpens the contrast for a better view when a part of the image is too light to see. Off: Disables “Studio Gain”. On: Enables “Studio Gain”.
Options Adjustments Item Adjustments 3D Safety Precautions show/hide is set during power ON. On: 3D Safety Precaution is shown every time when the power is ON. Off: 3D Safety Precaution is not shown when the power is ON. When the setting changes from “On” to “Off”, the confirmation screen is displayed as below. Pressing “YES” switches the setting. 3D Safety Precautions 3D Safety Precautions If Off is selected, the 3D safety precautions will not be displayed when power is turned on.
Options Adjustments 5 Press to select a command number. Press to show the previous / next command pages (1-8) of the selected program. Press to show the command setting screen.
Options Adjustments Audio input select Set up the sound when an image input is selected. Options 1/3 Weekly Command Timer Audio input select Input Search Onscreen display On Press ACTION ( ) button Audio input select Press to select image input. Press to select audio input.
Options Adjustments Input Search When a signal is not detected, another input with a signal is automatically selected. Options 1/3 Weekly Command Timer Audio input select Input Search Press ACTION ( ) button 1 select Input Search Input Search Primary Input Secondary Input 2 adjust Off Input Search Off: When there is no signal, the input is not switched automatically. All Inputs: Searches all inputs and switches to an input with a signal. Input search is executed in the following order.
there is any abnormality in the electronic pen, see “Electronic Troubleshooting • When Pen Operations” of the Operating Instructions. Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Sound Interference Noisy Sound Normal Picture No Sound Checks Electrical Appliances Cars / Motorcycles Fluorescent light Volume (Check whether the mute function has been activated on the remote control.) Check if speakers are connected properly.
List of Aspect Modes Aspect mode All Aspect: Factory setting On All Aspect: Off 16:9 14:9 16:9 Just – The pictures with a 4:3 aspect ratio among the 16:9 aspect ratio signals are enlarged horizontally so that the picture distortion is minimized. The left and right edges of the pictures are cut off. The display of the areas around the left and right edges of the screen is slightly elongated.
Applicable Input Signals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Signal name Horizontal frequency (kHz) Vertical frequency (Hz) 525 (480) / 60i 525 (480) / 60p 625 (575) / 50i 625 (576) / 50i 625 (575) / 50p 625 (576) / 50p 750 (720) / 60p 750 (720) / 50p 1,125 (1,080) / 60p 1,125 (1,080) / 60i 1,125 (1,080) / 50p 1,125 (1,080) / 50i 1,125 (1,080) / 24sF 1,125 (1,080) / 30p 1,125
Applicable Input Signals Video input (VIDEO) Signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Horizontal frequency(kHz) 15.73 15.63 15.73 15.63 15.73 Vertical frequency(Hz) 59.94 50.00 59.94 50.00 59.94 Shipping condition This function allows you to reset the unit to the factory setting. 1 2 Setup Press to display the Setup menu. Press to select “OSD Language”. Press for more than 3 seconds.
Command list of Weekly Command Timer No.
Specifications TH-65PB1E / TH-65PB1EK 220 - 240 V AC, 50/60 Hz Power Source Power Consumption Power on Stand-by condition Power off condition Plasma Display panel Screen size (No.
This product incorporates the following software: (1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software licensed under the GNU General Public License, Version 2.0 (GPL-2.0), (4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL-2.1) and/or, (5) open source software other than the software licensed under the GPL and/or LGPL.
