Model No. TH-42PF30ER TH-50PF30ER Operating Instructions High Definition Plasma Display English Please read these instructions before operating your set and retain them for future reference.
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.
Important Safety Notice WARNING 1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping or splashing. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) No naked flame sources, such as lighted candles, should be placed on / above the set. 2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety Precautions WARNING Setup This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Speakers ........................................................................ TY-SP42P8W-K (for TH-42PF30ER), TY-SP50P8W-K (for TH-50PF30ER) • Pedestal ...............................................
Safety Precautions When using the Plasma Display The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display. Do not stick any foreign objects into the Plasma Display. • Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause fire or electric shock.
Safety Precautions CAUTION When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. • Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result. Be sure to disconnect all cables before moving the Plasma Display.
Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. Lithium Battery Batteries must not be exposed to excessive heat such as sunshine, fire or the like. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully.
Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Accessories Accessories Supply Check that you have the accessories and items shown Operating Instruction book CD-ROM (Operating instructions) Power supply cord Remote Control Transmitter N2QAYB000535 Clamper × 1 TMME289 Batteries for the Remote Control Transmitter (R6 (UM3) Size × 2) Ferrite core × 2 J0KG00000014 Use the Ferrite cores to comply with the EMC standard. (see page 60) Remote Control Batteries Requires two R6 batteries. 1. Pull and hold the hook, then open the battery cover. 2.
Connections Speaker connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. 1 Speakers (Optional accessories) Red Black While pressing the lever, insert the core wire. 2 Red Speaker terminal (L) Speaker terminal (R) Black Return the lever.
Connections Video equipment connection 3D IR TRANSMITTER: Connect the 3D IR TRANSMITTER (optional accessory). SERIAL: Control the Plasma Display by connecting to PC (see page 14) SLOT: Terminal board (optional accessories) insert slot (see Note: page 4) The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. LAN: Connect to a network to control the unit.
Connections HDMI connection [Pin assignments and signal names] Signal name Pin No. 1 2 3 4 5 6 7 8 9 10 Pin No. T.M.D.S Data2+ 11 T.M.D.S Data2 Shield T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1 Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0 Shield T.M.D.S Data0T.M.D.S Clock+ Signal name T.M.D.S Clock Shield 12 T.M.D.S Clock- 13 CEC 14 Reserved (N.C.
Connections PC Input Terminals connection (Female) Shared with DVI-D IN. COMPUTER Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. Conversion adapter (if necessary) RGB PC cable Mini D-sub 15p (Male) Notes: • With regard to the typical PC input signals that are described in the applicable input signals list (see page 67), adjustment values such as for the standard picture positions and sizes have already been stored in this unit.
Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to “RS-232C”. (see page 52) (Male) COMPUTER 9 5 RS-232C Straight cable 8 4 7 3 6 2 1 Pin layout for SERIAL Terminal (Female) D-sub 9p Notes: • Use the RS-232C straight cable to connect the computer to the Plasma Display.
Power On / Off Connecting the AC cord plug to the Plasma Display. Connecting the plug to the Wall Outlet Notes: • Main plug types vary between countries. The power plug shown at right may, therefore, not be the type fitted to your set. • When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. INPUT MENU -/ VOL +/ ENTER/ Power Indicator Press the Power switch on the Plasma Display to turn the set on: Power-On.
Power On / Off When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the items with the remote control. Unit buttons are invalid. OSD Language English (UK) Deutsch OSD Language Français Italiano 1 Select the language. Español ENGLISH (US) 2 Set. Select Set PRESENT TIME Setup 1 Select “DAY” or “PRESENT TIME”. 2 Setup “DAY” or “PRESENT TIME”. 1 Select “Set”.
Power On / Off Power ON warning message The following message may be displayed when turning the unit power ON: 3D Safety Precautions When 3D images will be viewed by unspecified number of people or used for commercial applications, someone in authority should convey the following precautions. These precautions should be followed in the home as well. 3D Viewing/ 3D Content/ Viewing distance/ 3D Eyewear recommendations - To enjoy 3D images safely and comfortably, please read the Operating Instructions fully.
Basic Controls Main Unit Remote control sensor Volume Adjustment Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” : press to move the cursor down (see page 24) INPUT MENU -/ Main Power On / Off Switch Power Indicator The Power Indicator will light. • Power-OFF .... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) • Standby ........
Basic Controls Remote Control Transmitter ACTION button Press to make selections. ASPECT button Press to adjust the aspect. (see page 20) Standby (ON / OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 15). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. POS.
ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law.
Digital Zoom This displays an enlargement of the designated part of the displayed image. 1 Display the operation guide. Exit Press to access Digital Zoom. The operation guide will be displayed. 1 During Digital Zoom, only the following buttons can be operated. [Remote control] OFF TIMER button [Unit] VOL button INPUT MENU -/ VOL +/ ENTER/ MUTE button VOL button POSITION / ACTION button 2 Select the area of the image to be enlarged. Press on the enlargement location to select.
Viewing 3D images You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear (optional). Note: You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display. For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear. This display supports “Frame Sequential*1”, “Side by Side*2”, “Top and Bottom*3” and “Simultaneous*4” 3D formats.
Viewing 3D images Troubleshooting for 3D Eyewear Symptoms Checks Cannot see 3D images 3D Eyewear is turned off automatically There is something wrong with the 3D images • Has the 3D Eyewear been switched On? • Ensure that “3D Picture Display” in “3D Settings” is set to “3D”. (see page 35) • Some 3D image signals may not be automatically recognized as 3D images. Set “3D Picture Format” in “3D Settings” to match the picture format.
On-Screen Menu Displays Remote Control Unit 1 Display the menu screen. Press several times. MENU Press to select. (Example: Picture menu) 2 Select the item. Select. Picture Normalise Each time the MENU button is pressed, the menu screen will switch. Normal Viewing Picture Sound Pos./Size Setup Select. Press. Normal Normal Picture Mode Contrast Brightness Colour Hue Sharpness White balance Advanced settings 25 0 0 0 5 Normal Memory save Memory load Memory edit (Example: Picture menu) 3 Set.
Adjusting Pos./Size 1 Press to display the Pos./Size menu. 2 Press to select the menu to adjust. 3 Press to adjust the menu. 4 Press to exit from adjust mode. Pos./Size Normalise Auto Setup H-Pos H-Size V-Pos V-Size Dot Clock Clock Phase Clamp Position 1:1 Pixel Mode Normal 0 0 0 0 0 0 0 Off Note: Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode.
Adjusting Pos./Size Notes: • If the dot clock frequency of an analog signal is 162 MHz or higher, “Dot Clock” and “Clock Phase” cannot be automatically corrected. • When digital signal input, Dot Clock and Clock Phase cannot be made. • Auto Setup may not work when a cropped or dark image is input. In such case, switch to a bright image with borders and other objects are clearly shown, and then try auto setup again. • Depending on the signal, out of alignment may occur after Auto Setup.
Adjusting Pos./Size Clamp Position (During Component/PC input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green. Optimum value for Clamp Position adjustment When black parts have no detail due to underexposure (blackout) → Value that causes least blackout is the optimum. When black parts are tinged with green → Value that cancels the greenishness without causing blackout is the optimum.
Picture Adjustments 1 Press to display the Picture menu. 2 Select to adjust each item. Press to select the menu to adjust. Select the desired level by looking at the picture behind the menu. Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting. Picture Normalise Press “ ” or “ ” button to switch between modes.
Picture Adjustments Item Contrast Brightness Colour Hue Sharpness Effect Less Adjustments More Darker Brighter Less More Reddish Greenish Less More Selects the proper brightness and density for the room. Adjusts for easier viewing of dark pictures such as night scenes and black hair. Adjusts colour saturation. Notes: • You can change the level of each function (Contrast, Brightness, Colour, Hue, Sharpness) for each Picture Mode.
Picture Profiles Up to 8 combinations of picture adjustment values (in the Picture menu and Advanced settings) can be stored in the display memory as profiles and applied as needed, for a convenient way to enjoy your preferred picture settings.
Picture Profiles Saving profiles Follow these steps to save picture adjustment values as profiles. Note: When the settings are locked in “Extended life settings”, profiles cannot be saved. 1 Specify the picture quality in the Picture menu and Advanced settings. (see page 29, 30) 2 In the Picture menu, select “Memory save”. 3 5 1 select Memory save Memory load Memory edit 2 access A N a n 0 ! _ Select a profile name for saving the picture adjustment values. 1 select Memory save 1. [ 2. [ 3. [ 4.
Picture Profiles Loading profiles Load profiles and apply the picture adjustment values to the display as follows. Notes: • Loaded profiles are stored in memory according to the selected input terminal. (see page 17) • When the settings are locked in “Extended life settings”, profiles cannot be loaded. 1 In the Picture menu, select “Memory load”. 1 select Memory save Memory load Memory edit 2 Select the profile to load. 1 select Memory load 2 access 1. [ 2. [ 3. [ 4.
Sound Adjustment 1 Normalise 2 Select to adjust each item. Press to select the menu to adjust. Select the desired level by listening to the sound. 3 1/2 Sound Press to display the Sound menu. Normal Sound Mode Bass Mid Treble Balance Surround Normal 0 0 0 0 Off Press to exit from adjust mode. Item Sound Mode Bass Mid Treble Balance Surround Details Normal: Emits the original sound. Dynamic: Accentuates sharp sound. Clear: Attenuates human voice. Adjusts low pitch sounds. Adjusts normal sounds.
PRESENT TIME Setup / Set up TIMER The timer can switch the Plasma Display On or Off. Before attempting Timer Set, confirm the PRESENT TIME and adjust if necessary. Then set POWER ON Time / POWER OFF Time. 1 2 Setup Press to display the Setup menu. Press to select Set up TIMER or PRESENT TIME Setup. Press to display the Set up TIMER screen or PRESENT TIME Setup screen.
3D Settings To view the 3D images, please adjust and setup the 3D settings. Note: Set these settings for each input terminals.
Screensaver (For preventing image retention) Do not display a still picture, especially in 4:3 mode, for any length of time. If the display must remain on, a Screensaver should be used. 1 Press to display the Setup menu. Press to select Screensaver. 2 Press to display Screensaver screen.
Screensaver (For preventing image retention) Setup of Screensaver Time After selecting Time Designation, Interval or Standby after SCR Saver, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when “Mode” is “On” or “Off”.) Press to select Start Time / Finish Time (when Time Designation is selected). Press to select Periodic Time / Operating Time (when Interval is selected).
Reduces screen image retention Extended life settings The following settings are setup to reduce image retention: Setup 1/2 Express settings Custom settings Reset 3D Settings Signal Screensaver Extended life settings Input label Component/RGB-in select Power save Standby save PC Power management DVI-D Power management No signal power off No activity power off OSD Language Extended life settings Set to the recommended value Set individually Reset to the factory settings Extended life settings RGB Off O
Reduces screen image retention NANODRIFT Saver Moves the display position of the screen slightly to reduce image retention on the display panel. Low–High: NANODRIFT Saver operates. The display position of the screen moves at set time intervals. You can set the screen movement range. Some of the screen may appear to be missing as a result of this operation. If you change the value, a mask is displayed in the range where the picture is missing as a result of position movement.
Reduces screen image retention Custom settings Set the individual “Image Retention Reduction” menu. 1 Select “Custom settings”. Extended life settings Express settings Custom settings Reset 1 select 2 access set each menu to the recommended setting: 2 To Select “Recommended settings”.
Reduces power consumption • Power save: When this function is turned On, luminous level of the Plasma Display is suppressed, so power consumption is reduced. • Standby save: When this function is turned On, power consumption of the microcomputer is reduced during power supply standby (see page 15, 17, 18), so standby power of the set is reduced. • PC Power management: When this function is set to On, it operates under the following conditions to turn the power on or off automatically.
Customizing the Input labels This function can change the label of the Input signal to be displayed. (see page 17) 1 2 3 Setup Press to display the Setup menu. 1/2 3D Settings Signal Screensaver Extended life settings Input label Component/RGB-in select Press to select Input label. Press to display the Input label screen. Power save Standby save PC Power management DVI-D Power management No signal power off No activity power off OSD Language Press to select image input. Press to change input label.
Selecting the On-Screen Menu Language 1 2 Press to display the Setup menu. Press to select the OSD Language. Press to select your preferred language. Selectable languages Setup English(UK) Deutsch Français Italiano Español ENGLISH(US) .......(Chinese) .......(Japanese) Русский .......
Setup for MULTI DISPLAY By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all screens. For this mode of operation, each plasma display has to be set up with a Display number to determine its location. Note: During Multi display, the 3D images are displayed as 2D images. (Example) group of 4 (2 × 2) group of 9 (3 × 3) group of 16 (4 × 4) group of 25 (5 × 5) How to Setup MULTI DISPLAY 1 Press to display the Setup menu.
Setup for MULTI DISPLAY Item Details Select “Off” or “On”. The brightness depends on each display’s setting. Equalize the brightness of all the displays. Off On AI-Synchronization Notes: • If you set AI-synchronization to On, the following menus will be unavailable and these settings will be fixed to the initial values. Picture menu: Colour, Hue, Input level (Advanced settings) • This function cannot be adjusted during input from VIDEO terminal. 4 Press to exit from Setup.
Set up for Portrait Divide an input image into 3 parts, and display one of them to a plasma display which is set vertically. The image will be enlarged 3 times and rotated 90-degree. (Example) Notes: • When using the Portrait function with displays set vertically, “Display orientation” in Setup menu has to be set to “Portrait” (see page 43). • Turn up the power switch for the upward direction when you set Display vertically. • During Portrait display, the 3D images are displayed as 2D images.
Set up for Portrait 5 Viewing Area / Location Viewing Area: Set a mode of image division for Portrait function. Location: Set a location of image to be displayed for Portrait function. Press to select Viewing Area or Location. Portrait Setup Press to select each functions. Portrait Setup Seam hides video Viewing Area Location AI-synchronization Notes: • For HD signal videos, the “Viewing Area” is set at “16:9”, and cannot be changed.
Setup for Input Signals Component / RGB-in select Select to match the signals from the source connected to the Component / RGB or PC input terminals. Y, PB, PR signals “Component” RGB signals “RGB” 1 2 Press to display the Setup menu. Press to select the “Component / RGB-in select”. Press to select the desired input signal. Component 3 RGB Press to exit from adjust mode.
Setup for Input Signals Signal menu Note: “Signal” setup menu displays a different setting condition for each input signal. 1 Setup 3D Settings Signal Screensaver Extended life settings Input label Component/RGB-in select Press to display the Setup menu. Press to select the “Signal”. 2 Power save Standby save PC Power management DVI-D Power management No signal power off No activity power off OSD Language Press to display the Signal menu. Press to select the menu to adjust.
Setup for Input Signals • Sync This function operates only during input from PC IN terminal. Setting RGB sync signal Confirm that the input is set to RGB input (this setting is valid only for RGB input signal). Auto: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync. on G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
Setup for Input Signals • Noise reduction Sets the following three NR (Noise Reduction) functions together. P-NR, Mosquito NR, Block NR ( Press to select “Noise reduction”. ) Noise reduction Off Press to select “Off”, “Min” , “Mid” , “Max” , “Advanced”. Advanced NR Sets the three NR functions separately. 1 Press to enter Advanced NR. 2 Noise reduction Press to select “Advanced”. Press to select P-NR, Mosquito NR or Block NR. Press to select “Off”, “Min”, “Mid”, “Max”.
Network Setup Make the various settings to use the network function. Setup MULTI DISPLAY Setup Portrait Setup Set up TIMER PRESENT TIME Setup Network Setup Display orientation 2/2 DHCP, IP address, Subnet mask, and Gateway settings 1 Set DHCP. When “Off” is selected, IP address and other settings can be set manually. Landscape 2 Select the item and press 3 Enter an address. IP address 192.168. I 0.
Options Adjustments Options 1 Press to display the Setup menu. Weekly Command Timer Audio input select Touch Panel settings Press to select “OSD Language”. 2 Onscreen display Initial input Initial VOL level Maximum VOL level Input lock Button lock Remocon User level Press for more than 3 seconds. Press to select “Options”. 3 Options Shipping Press to display the Options menu. Press to select your preferred menu. 4 Press to adjust the menu.
Options Adjustments Item Adjustments Input lock Locks the input switch operation. Off PC SLOT INPUT*1 VIDEO COMPONENT*2 HDMI DVI *1 “SLOT INPUT” is displayed when an optional Terminal Board is installed. When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed. *2 “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”. (see page 48) Notes: • Only the adjusted signal is displayed (see page 17).
Options Adjustments Item Adjustments Studio W/B Off: Nullify all the settings adjusted. On: Sets the colour temperature for TV studio. Note: Valid only when the “Warm” is set as “White balance” in Picture menu. Studio Gain Sharpens the contrast for a better view when a part of the image is too light to see. Off: Disables “Studio Gain”. On: Enables “Studio Gain”.
Options Adjustments Item Adjustments 3D Safety Precautions show/hide is set during power ON. On: 3D Safety Precaution is shown every time when the power is ON. Off: 3D Safety Precaution is not shown when the power is ON. When the setting changes from “On” to “Off”, the confirmation screen is displayed as below. Pressing “YES” switches the setting. 3D Safety Precautions 3D Safety Precautions If Off is selected, the 3D safety precautions will not be displayed when power is turned on.
Options Adjustments 5 Press to select a command number. Press to show the previous / next command pages (1-8) of the selected program. Press to show the command setting screen.
Options Adjustments Audio input select Set up the sound when an image input is selected. Options 1/3 Weekly Command Timer Audio input select Touch Panel settings On Onscreen display Press ACTION ( ) button Audio input select Press to select image input. Press to select audio input.
Options Adjustments Touch Panel settings (Settings when using Touch Panel) The mode to restrict NANODRIFT Saver (see page 39) operation when using Touch Panel (available as an option) is set up. Options 1/3 Weekly Command Timer Audio input select Touch Panel settings Press ACTION ( ) button Touch Panel settings Touch Panel mode Calibration mode On Set “Touch Panel mode” to “On”. 1 select NANODRIFT Saver in Touch Panel mode: On 2 adjust The value set for NANODRIFT turns into “On” and displayed in gray.
Using Network Function This unit has a network function to control the network connected display with your computer. Note: To use the network function, set each “Network Setup” setting and make sure to set the “Control I/F Select” to “LAN”. (see page 52) When “LAN” is set, the slot power is turned on, and power indicator is lit orange under the condition of power “Off” with remote control (stand-by state), regardless of the “Slot power” setting.
Using Network Function PJLink™ Protocol The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your computer using PJLink™ protocol. • Display setup • Display status query Supported commands Commands to control the unit with PJLink™ protocol are shown in the table below.
Using Web Browser Control You can use a Web browser to control the unit and set up a network and password. Before Using Web Browser Control To use the Web browser control, the unit and computer setups are required. Unit Setup Set each “Network Setup” setting and make sure to set the “Control I/F Select” to “LAN”. (see page 52) Computer Setup Disable the proxy server settings and enable JavaScript. (Windows) Disable proxy server settings 1 Display [Internet Properties] window.
Using Web Browser Control TOP screen structure of the Web browser control After logging in, the TOP screen of the Web browser control is displayed. Menu Menu items are displayed. When a button is clicked, setup screen of each item is displayed. Item BASIC CONTROL OPTION CONTROL NETWORK SETTING CHANGE PASSWORD Details BASIC CONTROL screen is displayed. (see below) OPTION CONTROL screen is displayed. (see below) Network Setup screen is displayed. (see page 64) Password setup screen is displayed.
Using Web Browser Control NETWORK SETTING (Network Setup Screen) Click NETWORK SETTING from the menu. Various settings of a network can be set. For the details of the setting items, please check Network Setup under the Set up of the unit. (see page 52) Item Notes: • To use a DHCP server, make sure the DHCP server is started. • During a DHCP server is used, IP ADDRESS, SUBNET MASK, and GATEWAY values cannot be entered. • When the set values are changed properly, “NETWORK SETTING CHANGED.
Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Sound Interference Noisy Sound Normal Picture No Sound Checks Electrical Appliances Cars / Motorcycles Fluorescent light Volume (Check whether the mute function has been activated on the remote control.
List of Aspect Modes Aspect mode All Aspect: Factory setting On All Aspect: Off 16:9 14:9 16:9 Just – The pictures with a 4:3 aspect ratio among the 16:9 aspect ratio signals are enlarged horizontally so that the picture distortion is minimized. The left and right edges of the pictures are cut off. The display of the areas around the left and right edges of the screen is slightly elongated.
Applicable Input Signals *Mark: Applicable input signal Signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 525 (480) / 60i 525 (480) / 60p 625 (575) / 50i 625 (576) / 50i 625 (575) / 50p 625 (576) / 50p 750 (720) / 60p 750 (720) / 50p 1,125 (1,080) / 60p 1,125 (1,080) / 60i 1,125 (1,080) / 50p 1,125 (1,080) / 50i 1,125 (1,080) / 24sF 1,125 (1,080) / 30p 1,125 (1,080) / 25p 1,125 (1,080) / 24p 1
Applicable Input Signals Video input (VIDEO) Signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Horizontal frequency(kHz) 15.73 15.63 15.73 15.63 15.73 Vertical frequency(Hz) 59.94 50.00 59.94 50.00 59.94 Shipping condition This function allows you to reset the unit to the factory setting. 1 2 Setup Press to display the Setup menu. Press to select “OSD Language”. Press for more than 3 seconds. 3 Press to select “Shipping”.
Command list of Weekly Command Timer No.
Specifications TH-42PF30ER Power Source Power Consumption Power on Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Colour System Scanning format PC signals Connection terminals LAN AV IN VIDEO AUDIO L-R HDMI COMPONENT/RGB IN Y/G PB/CB/B PR/CR/R AUDIO L-R DVI-D IN AUDIO PC IN TH-50PF30ER 220 - 240 V AC, 50/60 Hz 365 W 445 W Save off 0.8 W, Save on 0.5 W Save off 0.8 W, Save on 0.5 W 0.3 W 0.
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
