Model No. TH-103VX200U TH-85VX200U Operating Instructions High Definition Plasma Display English Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt as well, and record the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Precautions CAUTION This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Pedestal ..................................................... TY-ST85P12 (for TH-85VX200U) TY-ST103PF9 (for TH-103VX200U) • Floor stand ................................................
Safety Precautions For sufficient ventilation; (TH-85VX200U) If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, and 6.0” (15 cm) or more at the rear, and also keep the space between the bottom of the display and the floor surface. If using some other setting-up method, follow the manual of it.
Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. Lithium Battery Batteries must not be exposed to excessive heat such as sunshine, fire or the like. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully.
Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Accessories Accessories Supplied Check that you have the Accessories and items shown Remote Control Transmitter N2QAYB000562 Batteries for the Remote Control Transmitter (AA Size × 2) Fixing band × 2 TMME203 TH-85VX200U Clamper × 1 TMM15412-2 TH-103VX200U AC cord Use the clamper when connecting a LAN cable. (see page 58) 3D Eyewear set (see page 23) Operating Instructions Screwdriver For 3D Eyewear (see page 24) These accessories will be used by professional installers when they install the unit.
Connections AC cord connection and fixing, cable fixing TH-85VX200U AC cord of this model is fixed and connected to the main unit. No AC cord needs to be connected. – How to Unfasten the AC cord Loosen the fixing band securing the AC cord. To loosen: Push the catch Pull – Cable fixing bands Secure any excess cables with bands as required. Note: Two fixing bands are supplied with this unit. In case of securing cables at three positions, please purchase it separately.
Connections TH-103VX200U – AC cord fixing Unplug the AC cord Close Push until the hook clicks. 1 Plug the AC cord into the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper. Note: Make sure that the AC cord is locked on both the left and right sides. – Cable fixing bands Open 2. Pull off. 1. Keep the knob pressed. Unplug the AC cord pressing the two knobs.
Connections Video equipment connection SERIAL Control the Plasma Display by connecting to PC. (see page 16) LAN Connect to a network to control the unit. (see page 58) COMPONENT/RGB IN Component/RGB Video Input Terminal (see page 14) 3D SHUTTER OUT Connect the 3D IR TRANSMITTER (optional accessory). PC IN PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. (see page 15) AUDIO OUT Connect to sound equipment.
Connections HDMI connection [Pin assignments and signal names] Pin No. Signal Name Pin No. Signal Name T.M.D.S Clock Shield 1 T.M.D.S Data2+ 11 2 T.M.D.S Data2 Shield T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1 Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0 Shield T.M.D.S Data0T.M.D.S Clock+ 12 T.M.D.S Clock- 13 CEC 14 Reserved (N.C.
Connections PC Input Terminals connection (Female) COMPUTER Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. Conversion adapter (if necessary) Mini D-sub 15p RGB PC cable (Male) Notes: • With regard to the typical PC input signals that are described in the applicable input signals list (see page 65), adjustment values such as for the standard picture positions and sizes have already been stored in this unit.
Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. Note: To use serial control for this unit, make sure to set the “CONTROL I/F SELECT” in the “NETWORK SETUP” menu to “RS-232C”. (see page 55) COMPUTER (Male) RS-232C Straight cable (Female) 9 5 D-sub 9p Notes: • Use the RS-232C straight cable to connect the computer to the Plasma Display. • The computer shown is for example purposes only.
Power ON / OFF Connecting the AC cord plug to the Plasma Display. For TH-103VX200U Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 12) Connecting the plug to the Wall Outlet. Note: For TH-103VX200U When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. Right side surface Main Power On / Off Switch Press the Power switch on the Plasma Display to turn the set on: Power-On.
Power ON / OFF When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the language with the remote control. Unit buttons are invalid. OSD LANGUAGE 1 OSD LANGUAGE Select the language. English (UK) Deutsch Français 2 Set. Italiano Español ENGLISH (US) Notes: • Once the language is set, this screen won’t be displayed when switching on the unit next time. • After the setting, language selection can be done from the SET UP menu.
Selecting the input signal Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. INPUT HDMI1 HDMI2 HDMI3 HDMI input terminals in HDMI 1 to HDMI 4. HDMI4 COMPONENT PC Component or RGB input terminal in COMPONENT/RGB IN.* PC input terminal in PC IN. * “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.
Basic Controls Main Unit Right side surface ENTER/ Enter / Aspect button (see page 22, 27) Up / Down button When the menu screen is displayed: “▲” : press to move the cursor up “▼” : press to move the cursor down (see page 27) MENU Infrared transmitter for 3D Eyewear Note: Do not place any objects between the transmitter and 3D Eyewear. Remote control sensor Power Indicator The Power Indicator will light. • Power-OFF ......
Basic Controls Remote Control Transmitter Standby (ON / OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 17). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. PC button Press to select PC input. (see page 19) LIGHT button The remote control’s buttons illuminate. MENU button Displays menu screen.
ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law.
Viewing 3D images You can enjoy viewing 3D images with contents or programmes corresponding to the 3D effect by wearing the 3D Eyewear (supplied). This display supports “Frame Sequential*1”, “Side by Side*2” and “Top and Bottom*3” 3D formats.
Viewing 3D images ■Replacing the battery When the battery is running low, the indicator lamp flashes 5 times on turning the 3D Eyewear on. In this case, early battery replacement is recommended. • Dispose of the old batteries as non-burnable rubbish, or in line with the waste disposal regulations in your local area.
Viewing 3D images To view the 3D images To view the contents of the Frame Sequential format (ex. 3D-compatible Blu-ray Disc, etc.) with 3D effect Connect the 3D-compatible player via an HDMI cable (see page 14) and playback the contents. • Use fully wired HDMI compliant cable. • For the settings of the player, read the manual of the player. • If you use the non 3D-compatible player, the images will be displayed without 3D effect.
Viewing 3D images Troubleshooting for 3D Eyewear Symptoms Checks Cannot see 3D images 3D Eyewear is turned off automatically There is something wrong with the 3D images The indicator lamp does not light when pressing the power button on the 3D Eyewear • Has the 3D Eyewear been switched On? • Ensure that “3D EYEWEAR” in “3D SETTINGS” is set to “ON”. (see page 47) • Some 3D image signals may not be automatically recognized as 3D images. Set “3D INPUT FORMAT” in “3D SETTINGS” to match the picture format.
On-Screen Menu Displays Remote Control 1 Display the menu screen. MENU Press 2 Select the menu. PICTURE 2 Access 1 Select NORMALIZE SET UP PICTURE MENU POS. /SIZE PICTURE SOUND Press several times. Each time the MENU button is pressed, the menu screen will switch. Normal Viewing PICTURE SET UP SOUND POS. /SIZE MONITOR BRIGHTNESS 0 SHARPNESS 0 COLOR TEMP OPTIONS Unit WARM ADVANCED SETTINGS MEMORY SAVE MEMORY LOAD The menu can be displayed directly by pressing these buttons.
Adjusting POS. /SIZE 1 Display the menu screen. 2 Select “POS. /SIZE”. 2 access 1 select 2 adjust 1 select PICTURE SET UP POS. /SIZE SOUND 3 Select the item and set. NORMALIZE AUTO SETUP H-POS 0 H-SIZE 0 V-POS 0 V-SIZE 0 DOT CLOCK 0 CLOCK PHASE 0 0 CLAMP POSITION 1:1 PIXEL MODE OFF UNDER SCAN OFF Note: Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode. 4 Exit the menu. To display a menu for adjustment of the POS.
Adjusting POS. /SIZE ● AUTO SETUP H-POS/V-POS, H-SIZE/V-SIZE, DOT CLOCK and CLOCK PHASE are automatically adjusted when the RGB or PC signal is received. This setting is enabled under the following conditions: • When “COMPONENT/RGB-IN SELECT” or “YUV/RGB-IN SELECT” in the “SET UP” menu (see page 44) is set to “RGB”, this setting is enabled.
Adjusting POS. /SIZE ● OVER SCAN Turn image over scan ON/OFF. Configurable signals are as follows: 525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI) ON OFF Notes: • When “OFF” is set, “H-SIZE” and “V-SIZE” cannot be adjusted. • When the “UNDER SCAN” is set to “ON”, this setting will be invalid. ● CLAMP POSITION (During Component and RGB input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green.
PICTURE Adjustments 1 Display the menu screen. 2 Select “PICTURE”. PICTURE 2 access 1 select 2 adjust 1 select SET UP POS. /SIZE SOUND 3 Select the item and set. NORMALIZE PICTURE MENU STANDARD PICTURE 25 BRIGHTNESS 0 COLOR 6 TINT 0 SHARPNESS 5 COLOR TEMP Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting. NORMAL ADVANCED SETTINGS 4 Exit the menu.
PICTURE Adjustments ● PICTURE MENU You can switch to the optimal picture mode for the video source and viewing environment. STANDARD MONITOR DYNAMIC CINEMA STANDARD: CINEMA: For viewing in standard (evening lighting) environments. Ideal for movies. This menu selects the normal levels of BRIGHTNESS MONITOR: and PICTURE. For use when creating broadcast or movie content. With DYNAMIC: this picture, even if the overall average picture level For viewing in brighter environments.
PICTURE Adjustments ADVANCED SETTINGS Enables fine picture adjustment at a professional level. Notes: • The adjustment values are memorized separately for each input terminal. • The adjustment range values should be used as an adjustment reference. Select the item and set.
PICTURE Adjustments ● 3:2 PULLDOWN When “ON”, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are recorded at 24 frames per second. If the picture is not stable, turn the setting to “OFF”. OFF ON Note: When “ON”, this setting only affects the following signal input: • 525i (480i), 625i (575i), 1125 (1080) / 60i signal input during “COMPONENT” input signal.
PICTURE Adjustments Color space adjustment (COLOR GAMUT) Changes the color space to BT.709 signal standard chromaticity point and fine-tunes it. ADVANCED SETTINGS NORMALIZE BLACK EXTENSION 0 INPUT LEVEL 0 GAMMA W/B HIGH R 0 W/B HIGH G 0 W/B HIGH B 0 W/B LOW R 0 W/B LOW G 0 W/B LOW B 0 2 access 2.2 Select the item and set.
PICTURE Adjustments ● RESET Resets the adjustment value of color space. Note: This setting is reflected only for the selected input terminal and the “PICTUR MENU”. 1 Select “RESET”. COLOR GAMUT CUSTOM COLOR GAMUT 2 access 1 select 1 select 2 set EDIT R RATIO G RATIO B RATIO R G B 65535 2110 0 2900 65535 1760 0 0 65535 RESET 2 Select “OK”. COLOR GAMUT RESET OK CANCEL ● Chromaticity diagram The RGB triangle representing current color space is shown.
Picture Profiles Up to 16 combinations of picture adjustment values (in the PICTURE menu and ADVANCED SETTINGS) can be stored in the display memory as profiles and applied as needed, for a convenient way to enjoy your preferred picture settings. Note: If setting items (PITCURE menu and ADVANCED SETTINGS) are set differently between MEMORY SAVE and MEMORY LOAD, they may not reflect for MEMORY LOAD.
Picture Profiles Saving profiles Follow these steps to save picture adjustment values as profiles. Note: When the settings are locked in “EXTENDED LIFE SETTINGS”, profiles cannot be saved. 1 Specify the picture quality in the PICTURE menu and ADVANCED SETTINGS. (see page 31-36) 2 In the PICTURE menu, select “MEMORY SAVE”. MEMORY SAVE MEMORY LOAD MEMORY EDIT 3 2 access 1 select 5 MEMORY NAME INPUT A N a n 0 ! _ Select a profile name for saving the picture adjustment values.
Picture Profiles Loading profiles Load profiles and apply the picture adjustment values to the display as follows. Notes: • Loaded profiles are stored in memory according to the selected input interface. (see page 19) • When the settings are locked in “EXTENDED LIFE SETTINGS”, profiles cannot be loaded. In the PICTURE menu, select “MEMORY LOAD”.
Picture Profiles Editing profiles Delete or rename profiles as follows. Note: Locked profiles cannot be deleted. Note: Locked profiles cannot be renamed. 1 1 In the PICTURE menu, select “MEMORY EDIT”. MEMORY SAVE 2 MEMORY LOAD access MEMORY SAVE MEMORY LOAD MEMORY EDIT 2 In the PICTURE menu, select “MEMORY EDIT”. 1 2 Select “MEMORY DELETE”.
Picture Profiles Locking profiles You can lock saved profiles to restrict operations when the profiles are loaded. You can also set passwords. Notes: • When the lock is set in “EXTENDED LIFE SETTINGS”, profile cannot be locked. • If profile is locked, the menu operations of “EXTENDED LIFE SETTINGS” are restricted. (see page 52) 1 2 Display the menu screen. Select “OPTIONS” and hold more. access (3 seconds or more) 1 select PICTURE SET UP POS.
Picture Profiles Switches to “PICTURE MENU” mode display. 1 2 Follow steps 1–5 in the previous procedure, . Select “isf Mode”. MEMORY1 Lock1 MEMORY2 Off MEMORY12 Off isf Mode Off 2 adjust 1 select Change password 3 4 Specify “On” or “Off”. Exit the menu. Specifying “On” for isf Mode changes the “PICTURE MENU” mode display as follows.
SOUND Adjustment 1 Display the menu screen. 2 Select “SOUND”. 2 access 1 select 2 adjust 1 select PICTURE SET UP POS. /SIZE SOUND 3 Select the item and set. NORMALIZE BALANCE VOLUME 0 1 4 Exit the menu. Item Details BALANCE Adjusts left and right volumes. VOLUME Adjust the sound volume level. Helpful Hint ( NORMALIZE Normalization) While the “SOUND” menu is displayed, if the OK button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
SET UP menu 1 Display the menu screen. 2 Select “SET UP”. PICTURE 2 access 1 select SET UP POS. /SIZE SOUND 3 Select the item and set. 3D SETTINGS SIGNAL SCREENSAVER EXTENDED LIFE SETTINGS INPUT LABEL 2 adjust 1 select NETWORK SETUP COMPONENT/RGB-IN SELECT RGB EXTERNAL SCALER MODE OFF POWER SAVE PC POWER MANAGEMENT OFF OFF AUTO POWER OFF OFF OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) 4 Exit the menu.
SET UP menu EXTERNAL SCALER MODE OFF ON This menu can be used to specify whether the built-in scaler or an external scaler is used for scaler functions such as resizing and picture quality adjustment. The setting is valid with the following input signals. 1125 (1080) / 24p·25p·30p·50p·60p OFF: Use the built-in scaler. ON: Use an external scaler. Note: If “ON” is set when other than corresponding signal is input, “Input signal must be 1125p(1080p)”message is displayed.
SET UP menu POWER SAVE OFF ON When this function is turned ON, luminous level of the Plasma Display is suppressed, so power consumption is reduced. PC POWER MANAGEMENT OFF ON When this function is set to ON, it operates under the following conditions to turn the power on or off automatically. When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC signal input: → Power is turned off (standby); the power indicator lights up orange.
SET UP menu 3D SETTINGS If the 3D images are not displayed correctly or seem unusual, please adjust and setup the 3D settings. Select the item and set.
SET UP menu SIGNAL menu Note: “SIGNAL” setup menu displays a different setting condition for each input signal. Select the item and set.
SET UP menu • SYNC This function operates only during input from PC IN terminal. Setting RGB sync signal Confirm that the input is set to RGB input (this setting is valid only for RGB input signal). AUTO: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync. ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector. VBS: Uses a synchronized signal of Composite Sync input, which is input from the HD connector.
SET UP menu SCREENSAVER Do not display a still picture, especially in 4:3 mode, for any length of time. If the display must remain on, a SCREENSAVER should be used.
SET UP menu EXTENDED LIFE SETTINGS The following settings are setup to reduce image retention: EXTENDED LIFE SETTINGS 3D SETTINGS SCREENSAVER EXTENDED LIFE SETTINGS INPUT LABEL NETWORK SETUP 2 access 1 select COMPONENT/RGB-IN SELECT RGB EXTERNAL SCALER MODE OFF POWER SAVE PC POWER MANAGEMENT OFF OFF AUTO POWER OFF OFF OSD DESIGN OSD POSITION OSD LANGUAGE Set to the recommended value Set individually Reset to the factory settings EXPRESS SETTINGS SIGNAL TYPE1 UPPER LEFT ENGLISH (US) CUSTOM
SET UP menu NANODRIFT SAVER Moves the display position of the screen slightly to reduce image retention on the display panel. LOW-HIGH: NANODRIFT SAVER operates. The display position of the screen moves at set time intervals. You can set the screen movement range. Some of the screen may appear to be missing as a result of this operation. If you change the value, a mask is displayed in the range where the picture is missing as a result of position movement.
SET UP menu CUSTOM SETTINGS Set the individual “Image Retention Reduction” menu. 1 Select “CUSTOM SETTINGS”. EXTENDED LIFE SETTINGS 2 access 1 select 2 set EXPRESS SETTINGS CUSTOM SETTINGS RESET set each menu to the recommended setting: 2 To Select “RECOMMENDED SETTINGS”.
SET UP menu Customizing the Input labels This function can change the label of the Input signal to be displayed. (see page 19) Select an input terminal and set.
Network Setup Make the various settings to use the network function. 3D SETTINGS DHCP, IP ADDRESS, SUBNET MASK, and GATEWAY settings SIGNAL 1 Set DHCP. SCREENSAVER EXTENDED LIFE SETTINGS INPUT LABEL When “OFF” is selected, IP ADDRESS and other settings can be set manually. NETWORK SETUP COMPONENT/RGB-IN SELECT RGB 2 access 1 select 2 Select the item and press 3 Enter an address. IP ADDRESS 192.168. I 0. Use to select a digit. Use to change a number or input the numerical value from to .
OPTIONS Adjustments 1 Display the menu screen. 2 3 Select “OPTIONS”. Press for more than 3 seconds. PICTURE 2 access (more than 3 seconds) 1 select 2 set 1 select SET UP POS. /SIZE SOUND OPTIONS 4 Select the item and set. Onscreen display On All Aspect Off Auto Setup Off Studio mode Off 3D Emitter Function button assign 1 INT 3D settings Function button assign 2 Signal 3D Safety Precautions Memory lock 5 On Exit the menu.
OPTIONS Adjustments Item Adjustments Set the infrared transmitter for the 3D Eyewear. 3D Emitter INT: Use the infrared transmitter of the unit. EXT: Use the external 3D IR TRANSMITTER (available separately.) Set the function to operate when the FUNCTION button 1 to 2 on the remote control is pressed. 3D settings: The “3D SETTINGS” menu is displayed. Function button assign 1 Scrolling bar: The screen saver activates, and after 15 minutes, the display power shuts down (standby).
Using Network Function This unit has a network function to control the network connected display with your computer. Note: To use the network function, set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” to “LAN”. (see page 55) When “LAN” is set, power is supplied to LAN circuit, and power indicator is lit orange under the condition of power off with remote control (stand-by state).
Using Network Function PJLink™ Protocol The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your computer using PJLink™ protocol. • Display setup • Display status query Supported commands Commands to control the unit with PJLink™ protocol are shown in the table below.
Using Web Browser Control You can use a Web browser to control the unit and set up a network and password. Before Using Web Browser Control To use the Web browser control, the unit and computer setups are required. Unit Setup Set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” to “LAN”. (see page 55) Computer Setup Disable the proxy server settings and enable JavaScript. (Windows) Disable proxy server settings 1 Display [Internet Properties] window.
Using Web Browser Control TOP screen structure of the Web browser control After logging in, the TOP screen of the Web browser control is displayed. Menu Menu items are displayed. When a button is clicked, setup screen of each item is displayed. Item BASIC CONTROL OPTION CONTROL NETWORK SETTING CHANGE PASSWORD Details BASIC CONTROL screen is displayed. (see below) OPTION CONTROL screen is displayed. (see below) Network Setup screen is displayed. (see page 62) Password setup screen is displayed.
Using Web Browser Control NETWORK SETTING (Network Setup Screen) Click NETWORK SETTING from the menu. Various settings of a network can be set. For the details of the setting items, please check NETWORK SETUP under the SET UP of the unit. (see page 55) Item Notes: • To use a DHCP server, make sure the DHCP server is started. • During a DHCP server is used, IP ADDRESS, SUBNET MASK, and GATEWAY values cannot be entered. • When the set values are changed properly, “NETWORK SETTING CHANGED.
Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Checks Sound Interference Noisy Sound Electrical Appliances Cars / Motorcycles Fluorescent light Normal Picture No Sound Volume (Check whether the mute function has been activated on the remote control.
List of Aspect Modes Aspect mode All Aspect: Factory setting On All Aspect: Off 16:9 14:9 FULL JUST JUST Pictures with a 4:3 aspect ratio are enlarged horizontally so that the picture distortion is minimized. The left and right edges of the pictures are cut off. The display of the areas around the left and right edges of the screen is slightly elongated. 4:3 4:3 (1) 4:3 H-FILL Zoom ZOOM Zoom1 Zoom2 Zoom3 64 The display of the pictures fills the screen.
Applicable Input Signals *Mark: Applicable input signal Signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 525 (480) / 60i 525 (480) / 60p 625 (575) / 50i 625 (576) / 50i 625 (575) / 50p 625 (576) / 50p 750 (720) / 60p 750 (720) / 50p 1,125 (1,080) / 60p 1,125 (1,080) / 60i 1,125 (1,080) / 50p 1,125 (1,080) / 50i 1,125 (1,080) / 24sF 1,125 (1,080) / 30p 1,125 (1,080) / 25p 1,125 (1,080) / 24p 1
Shipping condition This function allows you to reset the unit to the factory setting. 1 Display the menu screen. 2 Select “SET UP”. 2 access 1 select 1 select 1 select 2 set 1 select 2 set PICTURE SET UP POS. /SIZE SOUND 3 Select “OSD LANGUAGE”.
Specifications Power Source Power Consumption Rated Power Consumption Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Scanning format PC signals TH-85VX200U 120 V AC, 50/60 Hz TH-103VX200U 200-240 V AC, 50/60 Hz 1,250 W 1,400 W 0.3 W 0.5 W 0.2 W 0.3 W Drive method : AC type 85-inch, Drive method : AC type 103-inch, 16:9 aspect ratio 16:9 aspect ratio 74.3” (1,889 mm) (W) × 41.8” (1,062 mm) (H) 89.
This product has software installed partially licensed under the Free BSD LICENSE. Free BSD LICENSE regulations under the above specifications are as follows: (These regulations are set by the third party; therefore the original (English) regulations are stated.) Copyright © 1980, 1986, 1993 The Regents of the University of California. All rights reserved.
