Operating Instructions Manual de instrucciones High Definition Plasma Display Alta definición Pantalla de plasma Model No. Número de modelo TH-42PF11UK TH-50PF11UK TH-58PF11UK TH-65PF11UK The illustration shown is an image. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. La ilustración mostrada es una imagen.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt as well, and record the model number and serial number of your set in the space provided on the rear cover of these instructions. Table of Contents Important Safety Instructions.............
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Precautions CAUTION This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Speakers ....................................................TY-SP42P8W-K (for TH-42PF11UK), TY-SP50P8W-K (for TH-50PF11UK), TY-SP58P10WK (for TH-58PF11UK), TY-SP65P11WK (for TH-65PF11UK) • Pedestal ..........
Safety Precautions / Maintenance WARNING Setup Do not place the Plasma Display on sloped or unstable surfaces. • The Plasma Display may fall off or tip over. Do not place any objects on top of the Plasma Display. • If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center. Do not cover the ventilation holes.
Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book Remote Control Transmitter EUR7636070R Fixing band × 1 AC cord Batteries for the Remote Control Transmitter (2 × AA Size) Remote Control Batteries Requires two AA batteries. 1. Pull and hold the hook, then open the battery cover. 2. Insert batteries - note correct polarity ( + and -). 3. Replace the cover.
Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 Speaker terminal (L) AC cord connection (see page 13) – AC cord fixing Speaker terminal (R) 2 Unplug the AC cord Close 1 Plug the AC cord into 1 1 the display unit. Plug the AC cord until it clicks. Push until the hook clicks. Unplug the AC cord pressing the two knobs.
Connections PC Input Terminals connection (Female) COMPUTER AUDIO PC IN TH-42PS9 Conversion adapter (if necessary) Mini D-sub 15p RGB PC cable (Male) Audio Stereo plug Connect a cable which matches the audio output terminal on the computer. Notes: • Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.
Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. (Male) COMPUTER 1 2 6 3 7 4 8 5 9 SERIAL RS-232C Straight cable Pin layout for SERIAL Terminal (Female) D-sub 9p Notes: • Use the RS-232C straight cable to connect the computer to the Plasma Display. • The computer shown is for example purposes only. • Additional equipment and cables shown are not supplied with this set.
Connections HDMI connection This unit has terminal boards equivalent to Dual HDMI Terminal Board (TY-FB10HMD) and BNC Component Video Terminal Board (TY-42TM6A) as standard equipment. [Pin assignments and signal names] Pin No. 1 2 3 4 5 6 7 8 9 10 Signal T.M.D.S Data2+ T.M.D.S Data2 Shield T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1 Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0 Shield T.M.D.S Data0T.M.D.S Clock+ Pin No. 11 Signal T.M.D.S Clock Shield 12 T.M.D.
Power ON / OFF Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 9) Connecting the plug to the Wall Outlet. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. INPUT MENU -/ VOL +/ ENTER/ Power Indicator Press the Power switch on the Plasma Display to turn the set on: Power-On.
Power ON / OFF When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the items with the remote control. Unit buttons are invalid. OSD LANGUAGE 1 OSD LANGUAGE Select the language. English (UK) Deutsch Français 2 Set. Italiano Español ENGLISH (US) Русский PRESENT TIME SETUP 1 Select “DAY” or “PRESENT TIME OF DAY”. 2 Setup “DAY” or “PRESENT TIME OF DAY”. 1 Select “SET”. 2 Set.
Initial selections Selecting the input signal Select the input signals to be connected by installing the optional Terminal Boards. Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. Input signals will change as follows: INPUT1 INPUT2A INPUT2B INPUT3 PC SLOT2 is for dual input so that you can select INPUT2A or INPUT2B for INPUT2.
Basic Controls Main Unit Remote control sensor Volume Adjustment Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” : press to move the cursor down (see page 23) INPUT MENU -/ VOL Main Power On / Off Switch Power Indicator The Power Indicator will light. • Power-OFF .... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) • Standby ......... Red • Power-ON ...... Green • DPMS .
Basic Controls Remote Control Transmitter R button (see page 23) Press the R button to return to previous menu screen. Status button Press the “Status” button to display the current system status. 1 Input label 2 Aspect mode (see page 18) 3 Off timer The off timer indicator is displayed only when the off timer has been set. 4 Clock display (see page 46) Standby (ON / OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 13).
ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law.
ASPECT Controls For PC signal input: 4:3 Zoom 16:9 For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p): 4:3 Zoom1 Zoom2 Zoom3 16:9 14:9 Just For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]: 4:3 Full Zoom1 Zoom2 Zoom3 16:9 14:9 Just1 Just2 4:3 (1) 4:3 (2) MULTI PIP You can display two pictures, such as a video image and computer image, in a two-screen display. (Use the remote control for this operation.
MULTI PIP During Blend PIP (Composite Screen Function) : A composite picture is displayed with the sub screen positioned over the main screen. For example, text data such as a computer image can be displayed as a caption over a movie or still image. One screen FULL P IN P Transparent Function and Insertion Function Two functions are available for blend PIP: the transparent function and the insertion function. Set these functions with “TRANSPARENCY” or “INSERT” in “MULTI PIP SETUP”.
MULTI PIP Selecting the Target Screen for Operations Each time this button is pressed, the target screen for operations changes. Operations on the main screen Operations on the sub screen INPUT1 PC INPUT1 PC Main screen Sub screen Main screen input mode Sub screen input mode Notes: • When operations are performed for the sub screen, the sub screen audio is played. • If no operations are performed, the operation target returns to the main screen after about 5 seconds*.
Digital Zoom This displays an enlargement of the designated part of the displayed image. 1 Display the operation guide. Press to access Digital Zoom. The operation guide will be displayed. EXIT 1 During Digital Zoom, only the following buttons can be operated. [Remote control] [Unit] POSITION / ACTION button INPUT MENU -/ VOL +/ ENTER/ VOL button VOL button MUTE button SURROUND button OFF TIMER button 2 Select the area of the image to be enlarged. Press on the enlargement location to select.
On-Screen Menu Display Remote Control Unit 1 Display the menu screen. Press several times. Press to select. (Example: PICTURE menu) 2 Select the item. PICTURE MENU Each time the MENU button is pressed, the menu screen will switch. Normal Viewing PICTURE SET UP SOUND POS. /SIZE Select. 1/2 Select. NORMALIZE NORMAL PICTURE MENU PICTURE BRIGHTNESS COLOR TINT SHARPNESS STANDARD 25 0 0 0 5 Press. (Example: PICTURE menu) 3 Set. Set. Set. Press. 4 Exit the menu. Press several times. MENU Press.
Adjusting POS. /SIZE 1 2 3 Press to display the POS. /SIZE menu. During “VIDEO (S VIDEO)”, “Digital”, “SDI” and “HDMI” input signal. POS. /SIZE Press to select the menu to adjust. NORMALIZE NORMAL AUTO SETUP H-POS H-SIZE V-POS V-SIZE 1:1 PIXEL MODE Press to adjust the menu. 0 0 0 0 OFF During “COMPONENT”, “RGB” and “PC” input signal. 4 POS. /SIZE NORMALIZE NORMAL AUTO SETUP Press to exit from adjust mode.
Adjusting POS. /SIZE 1:1 PIXEL MODE Adjusts the display size when 1125i, 1125p or 1250i signal is input. Notes: • Select ON when you would like to replay 1920 × 1080 input signal. • Applicable input signal; 1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i • Select OFF when flickering is shown around the image. • H-SIZE, V-SIZE and DOT CLOCK cannot be adjusted when ON is selected.
PICTURE Adjustments 1 Press to display the PICTURE menu. 2 Select to adjust each item. Press to select the menu to adjust. Select the desired level by looking at the picture behind the menu. Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
PICTURE Adjustments Item PICTURE BRIGHTNESS COLOR TINT SHARPNESS Effect Less Adjustments More Darker Brighter Less More Reddish Greenish Less More Adjusts the proper picture contrast. Adjusts for easier viewing of dark pictures such as night scenes and black hair. Adjusts color saturation. Adjusts for natural flesh tones. Adjusts picture sharpness. Notes: • “COLOR” and “TINT” settings cannot be adjusted for “RGB/PC” and “Digital” input signal.
SOUND Adjustment 1 SOUND Press to display the SOUND menu. 1/2 NORMALIZE NORMAL 2 AUDIO MENU BASS MID TREBLE BALANCE SURROUND AUDIO OUT (PIP) Select to adjust each item. Press to select the menu to adjust. Select the desired level by listening to the sound. 3 STANDARD 0 0 0 0 OFF MAIN Press to exit from adjust mode. Item AUDIO MENU BASS MID TREBLE BALANCE SURROUND Details STANDARD: Emits the original sound. DYNAMIC: Accentuates sharp sound. CLEAR: Attenuates human voice. Adjusts low pitch sounds.
PRESENT TIME SETUP / SET UP TIMER The timer can switch the Plasma Display ON or OFF. Before attempting Timer Set, confirm the PRESENT TIME OF DAY and adjust if necessary. Then set POWER ON TIME / POWER OFF TIME. 1 2 Press to display the SET UP menu. Press to select SET UP TIMER or PRESENT TIME SETUP. SET UP 2/2 MULTI DISPLAY SETUP MULTI PIP SETUP PORTRAIT SETUP SET UP TIMER PRESENT TIME SETUP DISPLAY ORIENTATION LANDSCAPE Press to display the SET UP TIMER screen or PRESENT TIME SETUP screen.
SCREENSAVER (For preventing image retention) Do not display a still picture, especially in 4:3 mode, for any length of time. If the display must remain on, a SCREENSAVER should be used. 1 Press to display the SET UP menu. Press to select the SCREENSAVER. 2 Press to select the SCREENSAVER screen.
SCREENSAVER (For preventing image retention) Reduces screen image retention These functions prevent the occurrence of an “image retention” on the display when turned ON. WOBBLING: Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of sharper contour of image. ON1: Shifts the image every 30 seconds. ON2: Shifts the image at a dot level pitch depending on screen-detection. PEAK LIMIT: Suppresses image contrast (peak brightness).
Reduces power consumption • POWER SAVE: • STANDBY SAVE: • POWER MANAGEMENT: • AUTO POWER OFF: 1 When this function is turned ON, luminous level of the Plasma Display is suppressed, so power consumption is reduced. When this function is turned ON, power consumption of the microcomputer is reduced during power supply standby (see page 13, 16, 17), so standby power of the set is reduced. When this function is set to ON, it operates under the following conditions to turn the power on or off automatically.
Customizing the Input labels This function can change the label of the Input signal to be displayed. Select the input signal which you would like to change its label before customizing the Input labels. (see page 15, 17) Press to select INPUT LABEL. SET UP 1/2 SIGNAL SCREENSAVER COMPONENT/RGB-IN SELECT RGB INPUT LABEL PC POWER SAVE OFF STANDBY SAVE OFF POWER MANAGEMENT OFF AUTO POWER OFF OFF OSD LANGUAGE ENGLISH (US) Press to change the INPUT LABEL.
SET UP for MULTI DISPLAY By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all screens. For this mode of operation, each plasma display has to be set up with a Display number to determine its location. (Example) group of 4 (2 × 2) group of 9 (3 × 3) group of 16 (4 × 4) group of 25 (5 × 5) How to setup MULTI DISPLAY 1 SET UP Press to display the SET UP menu. Press to select the MULTI DISPLAY SETUP.
SET UP for MULTI DISPLAY Item Details Select “OFF” or “ON”. Equalize the brightness of all the displays. The brightness depends on each display’s setting. AI-SYNCRONIZATION OFF ON Note: If you set AI-SYNCRONIZATION to ON, the following menus will be unavailable and these settings will be fixed to the initial values. PICTURE menu: COLOR, TINT, INPUT LEVEL (ADVANCED SETTINGS) 4 Press to exit from adjust mode.
MULTI PIP SETUP Set the two-screen display function that is activated when 1 is pressed. Press to select the MULTI PIP SETUP. MULTI PIP SETUP Press to display the “MULTI PIP SETUP” menu. MULTI PIP DISPLAY MODE TRANSPARENCY TRANSPARENCY LEVEL INSERT INSERT LEVEL Press to select the menu to adjust. Press to adjust the menu. 3 2/2 MULTI DISPLAY SETUP MULTI PIP SETUP PORTRAIT SETUP SET UP TIMER Press to display the SET UP menu.
SET UP for PORTRAIT Divide an input image into 3 parts, and display one of them to a plasma display which is set vertically. The image will be enlarged 3 times and rotated 90-degree. (Example) Note: When using the PORTRAIT function with displays set vertically, “DISPLAY ORIENTATION” in SET UP menu has to be set to “PORTRAIT” (see page 33). How to setup PORTRAIT 1 Press to display the SET UP menu. 2 Press to select the PORTRAIT SETUP. Press to display the “PORTRAIT SETUP” menu.
SET UP for PORTRAIT 5 VIEWING AREA / LOCATION VIEWING AREA: Set a mode of image division for PORTRAIT function. LOCATION: Set a location of image to be displayed for PORTRAIT function. Press to select VIEWING AREA or LOCATION. PORTRAIT SETUP PORTRAIT SETUP SEAM HIDES VIDEO VIEWING AREA LOCATION AI-SYNCHRONIZATION Press to select each function. OFF OFF 16:9 1 OFF Notes: • For HD signal videos, the “VIEWING AREA” is set at “16:9”, and cannot be changed.
SET UP for Input Signals COMPONENT / RGB IN SELECT Select to match the signals from the source connected to the COMPONENT / RGB input terminals. Y, PB, PR signals “COMPONENT” RGB signals “RGB” 1 2 SET UP Press to select the “COMPONENT / RGB-IN SELECT”. Press to select the desired mode. COMPONENT RGB 3 1/2 Press to display the SET UP menu.
SET UP for Input Signals SIGNAL menu Note: “SIGNAL” setup menu displays a different setting condition for each input signal. 1 2 SET UP SIGNAL SCREENSAVER COMPONENT/RGB-IN SELECT RGB PC INPUT LABEL POWER SAVE OFF STANDBY SAVE OFF POWER MANAGEMENT OFF AUTO POWER OFF OFF OSD LANGUAGE ENGLISH (US) Press to display the SET UP menu. Press to select the “SIGNAL”. Press to display the SIGNAL menu.
SET UP for Input Signals COLOR SYSTEM / Panasonic AUTO Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.(“SIGNAL [VIDEO]” menu is displayed.) Press to select the “COLOR SYSTEM” or “Panasonic AUTO”. Press to select each function. SIGNAL 3D Y/C FILTER (NTSC) COLOR SYSTEM 3 : 2 PULLDOWN Panasonic AUTO (4 : 3) If the image becomes unstable: With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases become unstable.
SET UP for Input Signals REFRESH RATE This function sets the refresh rate of the display. This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate. 100 Hz: Reduce screen flicker. 50 Hz: Enhance the resolution of moving images. Note: It is recommended to set to 100 Hz normally. Press to select REFRESH RATE. q REFRESH RATE 100 Hz Press to adjust. NOISE REDUCTION Sets the following three NR (Noise Reduction) functions together.
SET UP for Input Signals SYNC Select SIGNAL from the “SET UP” menu during RGB input signal. Press to select the “SYNC”. Press to adjust. [ RGB ] SIGNAL SYNC 3 : 2 PULLDOWN XGA MODE AUTO OFF 1024 × 768 Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT signal). AUTO: ON G: VBS: The H and V sync or synchronized signal are automatically selected. If both input, it is selected the H and V sync.
Options Adjustments 1 Options Press to display the Setup menu. Weekly Command Timer Press to select “OSD Language”. 2 3 Onscreen display Initial INPUT Initial VOL level Maximum VOL level INPUT lock Button lock Remocon User level Press and hold until the Options menu is displayed. Press to select your preferred menu. 4 Press to adjust the menu.
Options Adjustments Item Adjustments INPUT lock Off PC INPUT1 INPUT2 INPUT3 Locks the input switch operation. Notes: • Only the adjusted signal is displayed (see page 15). • Signal can be displayed when the Terminal board is installed. • Input switch can be used when this is set to “Off”. • In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input in the single screen display mode.
Options Adjustments Item Adjustments Studio W/B Off: Nullify all the settings adjusted. On: Sets the color temperature for TV studio. Note: Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu. Studio Gain Sharpens the contrast for a better view when a part of the image is too light to see. Off: Disables “Studio Gain”. On: Enables “Studio Gain”.
Options Adjustments Weekly Command Timer You can set 7-day timer programming by setting time and command. Note: Before setting Weekly Command Timer, set PRESENT TIME SETUP. (see page 29) 1 Press to select Function. Options Press to select “On”. 1/3 Weekly Command Timer On Onscreen display Note: • When Function is set to On, SET UP TIMER (see page 29) is unavailable and INTERVAL / TIME OF DAY in MODE of SCREENSAVER (see page 30) cannot be selected.
Options Adjustments Press to select Command No. 6 Press to select a command number. Command setting screen Weekly Command Timer Program 1 Command No Time Command Press to select Time / Command. 7 02 10:30 IMS:SL1 Weekly Command Timer Program 1 Press to set each item. 02 Command No Time: Set the time to execute a command program. 10:30 Time IMS:SL1 Command Pressing “ ” or “ ” button once changes “Time” 1 minute. Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Checks Sound Interference Noisy Sound Electrical Appliances Cars / Motorcycles Fluorescent light Normal Picture No Sound Volume (Check whether the mute function has been activated on the remote control.
List of Aspect Modes Aspect mode All Aspect: Factory setting On All Aspect: Off 16:9 14:9 FULL JUST JUST Pictures with a 4:3 aspect ratio are enlarged horizontally so that the picture distortion is minimized. The left and right edges of the pictures are cut off. The display of the areas around the left and right edges of the screen is slightly elongated. 4:3 4:3 (1) 4:3 H-FILL Zoom ZOOM Zoom1 Zoom2 Zoom3 50 The display of the pictures fills the screen.
Applicable Input Signals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 Signal name Horizontal frequency (kHz) Vertical frequency (Hz) 525 (480) / 60i 525 (480) / 60p 625 (575) / 50i 625 (575) / 50p 625 (576) / 50p 750 (720) / 60p 750 (720) / 50p 1,125 (1,080) / 60p 1,125 (1,080) / 60i 1,125 (1,080) / 50p 1,125 (1,080) / 50i 1,125 (1,080) / 24sF 1,125 (1,080) / 30p 1,125 (1,080) / 25p 1,125 (1,080) / 2
Applicable Input Signals VIDEO input (HDMI) Vertical Horizontal Dot clock frequency (Hz) frequency (kHz) (MHz) 1 VGA60 59.94 31.47 25.18 2 525/60p 59.94 31.47 27.00 3 625/50p 50.00 31.25 27.00 4 750/60p 60.00 45.00 74.25 5 750/50p 50.00 37.50 74.25 6 1125/60i 60.00 33.75 74.25 7 1125/50i 50.00 28.13 74.25 8 1125/60p∗ 60.00 67.50 148.50 9 1125/50p∗ 50.00 56.26 148.50 10 1125/24p∗ 24.00 27.00 74.25 ∗Not compatible with HDMI Terminal Board (TY-FB8HM). Audio signal Linear PCM : 48/44.
Command list of Weekly Command Timer No.
Specifications TH-42PF11UK Power Source Power Consumption Power on Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Scanning format PC signals Connection terminals HDMI A-B COMPONENT/RGB IN PC IN SERIAL SPEAKERS Accessories Supplied Remote Control Transmitter Batteries Fixing band Dimensions (W × H × D) Mass (weight) main unit only with speakers TH-50PF11UK 110 - 127 V AC, 50/60 Hz 525 W 605 W Save OFF 0.
Specifications TH-58PF11UK Power Source Power Consumption Power on Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Scanning format PC signals Connection terminals HDMI A-B COMPONENT/RGB IN PC IN SERIAL SPEAKERS Accessories Supplied Remote Control Transmitter Batteries Fixing band Dimensions (W × H × D) Mass (weight) main unit only with speakers TH-65PF11UK 110 - 127 V AC, 50/60 Hz 700 W 755 W Save OFF 1.
(for the U.S.A and Puerto Rico) Panasonic Professional Display Company Unit of Panasonic Corporation of North America One Panasonic Way 1F-10 Secaucus, NJ 07094 Panasonic Professional Flat Panel Display Limited Warranty Panasonic Professional Display Company.
(for Canada) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 LIMITED WARRANTY STATEMENT Panasonic Canada Inc. (also known as PCI) warrants this product to be free of defects in material and workmanship under normal use during the applicable warranty coverage period described below. PCI agrees to repair, or at its option, exchange, any part that becomes defective. However, the product must be purchased and serviced in Canada.
Note 59
Customer’s Record The model number and serial number of this product can be found on its back cover. You should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
