Model No. TH-152UX1 Operating Instructions High Definition Plasma Display Contents ● ● ● ● ● ● ● ● ● ● ● ● Important Safety Instructions .................................. 3 FCC STATEMENT .................................................. 4 Important Safety Notice .......................................... 5 Safety Precautions.................................................. 6 Accessories ...........................................................11 Connections .........................................
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Important Safety Notice WARNING 1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping or splashing. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) No naked flame sources, such as lighted candles, should be placed on / above the set. 2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety Precautions WARNING Setup This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Pedestal ......................................................................... TY-ST152UX1 • Mounting Bracket ...........................................................
Safety Precautions When using the Plasma Display The Plasma Display is designed to operate on 200 - 240 V AC, 50/60 Hz. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display. Do not stick any foreign objects into the Plasma Display. • Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause fire or electric shock.
Safety Precautions CAUTION When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. • Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result. Be sure to disconnect all cables before moving the Plasma Display.
Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. Lithium Battery Batteries must not be exposed to excessive heat such as sunshine, fire or the like. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully.
Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Accessories Accessories Supply Check that you have the accessories and items shown Operating Instruction book Remote Control Transmitter N2QAYB000560 Batteries for the Remote Control Transmitter (R6 (AA) Size × 2) These accessories will be used by professional installers when they install the unit.
Connections Video equipment connection Cable fixing Secure any excess cables with band as required. Note: Three fixing bands are supplied with this unit. In case of securing cables at six positions, please purchase it separately. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.
Power On / Off Turn on the breaker dedicated to the Plasma Display. Press the Power switch on the Plasma Display to turn the set on: Power-On. Power Indicator: Green Right side surface Main Power On / Off Switch Remote Control Sensor Press the Power Indicator button on the remote control to turn the Plasma Display off. Power Indicator: Red (standby) Press the button on the remote control to turn the Plasma Display on.
Power On / Off When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the items with the remote control. Unit buttons are invalid. OSD Language 1 OSD Language Select the language. English (UK) Deutsch 2 Set. Français Italiano Español ENGLISH (US) Notes: • Once the language is set, this screen won’t be displayed when switching on the unit next time. • After the setting, language selection can be done from the Setup menu.
Selecting the input signal Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. INPUT HDMI1 HDMI2 SLOT INPUT 4K-SDI 4K-DVI PC HDMI input terminal in HDMI 1. HDMI input terminal in HDMI 2. Input terminal in Terminal Board.* 4k2k HD-SDI input terminal in SDI IN. 4k2k DVI-D input terminal in DVI-D IN. PC input terminal in PC IN. * “SLOT INPUT” appears when the Terminal Board is connected.
Basic Controls Main Unit Right side surface ENTER/ Remote control sensor Enter / Aspect button (see page 18) Up / Down button When the menu screen is displayed: ▲ : press to move the cursor up ▼ : press to move the cursor down (see page 18) MENU INPUT MENU Screen ON / OFF Each time the MENU button is pressed, the menu screen will switch. (see page 18) Normal Viewing Pos. /Size Picture Setup INPUT button (INPUT signal selection) (see page 15) Power Indicator The Power Indicator will light.
Basic Controls Remote Control Transmitter AUTO SETUP button Automatically adjusts the position/size of the screen. Standby (ON / OFF) button The Plasma Display must first be turned on at the power switch (see page 13). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. LIGHT button The remote control’s buttons illuminate. HDMI buttons Press to select HDMI 1 or HDMI 2 input.
On-Screen Menu Displays Remote Control Unit 1 Display the menu screen. MENU Press to select. (Example: Picture menu) Press several times. Each time the MENU button is pressed, the menu screen will switch. Normal Viewing Picture Pos. /Size Setup 2 Select the item. Select. Picture Press. ENTER/ Normalise Normal Picture Mode Contrast Brightness Colour Hue Sharpness White balance Advanced settings Normal 25 0 0 0 5 Select.
Specifications Power Source Power Consumption Power on Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Scanning format PC signals Connection terminals AV IN HDMI 1/2 SDI IN*1 DVI-D IN*1 PC IN SERIAL 3D SHUTTER OUT*2 SLOT DVI-D IN Dimensions (W × H × D) Mass (weight) TH-152UX1 200 - 240 V AC, 50/60 Hz 3700 W 0.5 W 0.3 W Drive method : AC type 152-inch, 17:9 aspect ratio 134.4” (W) × 70.9” (H) × 152.
(for the U.S.A and Puerto Rico) Panasonic Solutions Company Unit of Panasonic Corporation of North America Three Panasonic Way 2F-5 Secaucus, NJ 07094 Panasonic Professional Flat Panel Display Limited Warranty Panasonic Solutions Company.
(for Canada) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 LIMITED WARRANTY STATEMENT Panasonic Canada Inc. (also known as PCI) warrants this product to be free of defects in material and workmanship under normal use during the applicable warranty coverage period described below. PCI agrees to repair, or at its option, exchange, any part that becomes defective. However, the product must be purchased and serviced in Canada.
Memo 23
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
