AQTE116 Please check and identify the supplied accessories. AC mains lead (1) (VJAO73) L 'J Remote control transmitter (1} T (RAK-SUATIWH) [7] eateries i2) rise numbers indicated in parentheses when asking for replacement parts. “The included AC mains lead is for use with this unit only, Do not use it with other equipment. Dear Customer Thank you for purchasing this Technicians product. For optimum performance and safety, please read these instructions carefully.
Caution for AC mains Lead {For Unequal Kingdom) {*EB" earn 8 medal only} For your safety, please read the following text carefully. This appliance is supplied with a molded three pin mains plug for your safely and convenience. A s-amperes fug is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a raking of 5-ampere and that it is approved by PASTA or BSI tg BS1362, Check for the PASTA mark < or the BSI mark & on the body of the ruse.
Before use . RQT5118 Suggestions for safety Placement Avoid placing the unit in areas of; » direct sunlight « high temperature * high humidity » expressive vibration * uneven surfaces (Place the unit on a flat level surface.) Such conditions might damage the cabinet and/or other component parts and thereby shorten the unit's service life. pR Never place heavy tams on top of the unit or the AG mains lead. LT »t is very dangerous to use an AG power secure of high voltage such as for an air conditioner.
Front panel controls No. Name Ref. page @ Unit fondant button and remote standby indicator Use this button to turn the unit on and off, = (off): The units in standby mode. {on): The unit is on. The unit cah be muted on and off with the remote control, When the units tuned off with the remote control it is in remote standby and the indicator lights. The unit is Still using a small amount of power in the standby and remote standby conditions. Standby uses less power. @ Operation indicator (OPERATION}) .
RTE? 16 Transmission window The remote control No. __Name @ Amp nonfood button (AMP (3} 15 Numbered Du Tons ..o someone @B Title BUN (TITLE v mummnrrsnrssmasssmsmsissessasesmvsen ) Band select button (BAND) (8 Deck 1/2 select button (DECKLE) 9 Input select buttons (TAPE 1, TAPE 2, CD, TUNER, MD, DVD, AUX, PHONON] Skip buttons { M, PP Jccrcrnncneen & Stop button (M) ..commonness . @ Muting button 10, 12 @ Audio equipment off button (AUDIO (O ).
Connections Stereo fiho}oo cable (not included) = White (L) H Red () MDY deck {or second tape deck) {not included) Taps deck (not included) ANALOG N ANALOG OuT o owe Bl G =009 CDJO:IO REC {IN)§ Tuner {not included) e OUTPUT T PLAY (OUT) Cooling fan The cooling fan operates at high power output levels only. Ground wire {not included ‘ R T GND! output OUTPUT 58380 COVET Turntable {pot included) 5 Second CO player, efc.
Before use .
; 1081 SPEAKERS \O/ I:IE:] N o TAPE MONITOR —w TAPE 1 TAPE 2MD SOURCE =" | WIRETAPPED AUX DVD CD Tug Er Phonon P30 000 N VOLUME Listening Preparation Before operation, set [VOLUME] o the “MIN” position. . Press About 4 seconds later, the “OPERATION" indicator will light up. Select the speakers to be used. “The corresponding speaker indicator will illuminate. Press [SOURCE]. Press input defect buttons to select the desired source. The corresponding indicator fights.
ions . FQTSH16 HOOTING VOLUME PHONES CH-Tn BASS TREBLE MIN MAx M\N Hax Headphones {(not included) Listening To adjust the sound balance u Turn [BALANCE] to adjust the firefight sound balance, e VGA circuit This unit features a state-of-the-art variable gain control amplifier {DOGCART.
¥ 5 monetizes e TAPE MONITOR —u Tape TAPE 20 SOURCE "oy R PHONON e TAPE MONITOR — TAPE } TARE MO SOURCE 208 O Q Recording Connect the tape deck or MD deck to either of the "REC (OUT} (TAPE 1 or TAPE 2/MDY" terminals on the back of the unit, II Press [SOURCE]. Press on input select button to select the source to be recorded. AUX: Equipment connected 1o the AUX terminal. DVD: DVD player €0: GO player {or CD hanger) TUNER: Tu net PHONON: Turntable Begin recording on tape deck or MD deck.
Using the remote control . APATITE Remote control operation The remote control can be used to operate other units manufactured by Technicians and Panasonic in addition to this system, including CD players {or CD changers), tuners, cassette decks, MD decks and DVD players which are equipped with a remits control sensor. Depending on the model, there may be cases where operation is not possible, For details on how to do this, refer 1o the operating instructions for the respective component.
Remote control operation CD player {or CD changer) and MD deck control {CD1..Set the remote control the CD player mode. Press this button first before trying to use the following buttons. « Yo turn the CD player {or CD changer) nonfood €1 {01 {This may not be passable with some models.) M G1® ® the remote control to the MD sack mode.
Using the remote control . RQTS118 Remote control operation Cassette deck control buttons [TAPE 1, TAPE [TAPE 1] {TAPE the cremate control to the cassette deck mode. Press the button which corresponds o the cassette deck being used (TAPE 1 or TAPE 2), Press one of these buttons first before trying 1o use the following buttons, * To turn the cassette deck nonfood [TAPE 1] or [TAPE {This may not be possible with some models.
Troubleshooting guide Before requesting service for this unit, check the chart below for a possible cause of the problem you are experiencing. Some simple checks or 3 mince adjustment on your part may eliminate the problem and restore proper operation.
e [ Technical specifications (piN 45 500; 20 Hz-20 kHz continuous power output {at 240 V) both channels driven {SU-A8DBI [BU-A707] 245 khz continuous power output both channels driven (THD: 1%) [SU-A808] 2X70W (8 Q) 2X 100 W (4 [SU-A707] 2X55 W (8 0} 2XKFOW (4 1) 63 Hz-12.5 kHz continuous power output both channels driven (THD: 0.7%) [SU-AB08] 2X68 W (8 €} 2X85W (40} [BU-TOT] 2X50 W (8 Q) 2XT70W (4.} Total harmonic distortion rated power st 20 Hz-20 kHz 0.
