VQT1D97(ENG).book 1 ページ ２００７年３月２０日 火曜日 午後５時３３分 Operating Instructions SD Video Camera Model No. SDR-S10P/PC Before connecting, operating or adjusting this product, please read the instructions completely. Spanish Quick Use Guide is included. Guía para rápida consulta en español está incluida. For USA assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.
VQT1D97(ENG).book 2 ページ ２００７年３月２０日 火曜日 午後５時３３分 Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. Be sure to retain this manual as your convenient camera information source. Date of Purchase Dealer Purchased From Dealer Address Dealer Phone No. Model No. Serial No.
VQT1D97(ENG).book 3 ページ ２００７年３月２０日 火曜日 午後５時３３分 THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
VQT1D97(ENG).book 4 ページ ２００７年３月２０日 火曜日 午後５時３３分 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
VQT1D97(ENG).book 5 ページ ２００７年３月２０日 火曜日 午後５時３３分 Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee.
VQT1D97(ENG).book 6 ページ ２００７年３月２０日 火曜日 午後５時３３分 IMPORTANT ∫ Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. Battery Battery pack (Lithium ion battery pack) ≥ Use the specified unit to recharge the battery pack. ≥ Do not use the battery pack with equipment other than the specified unit.
VQT1D97(ENG).book 7 ページ ２００７年３月２０日 火曜日 午後５時３３分 U.S.A./CANADA CONSUMERS: ATTENTION: A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. -If you see this symbolInformation on Disposal in other Countries outside the European Union This symbol is only valid in the European Union.
VQT1D97(ENG).book 8 ページ ２００７年３月２０日 Contents Before using Quick Guide ...............................10 Features .....................................14 Water resistance.......................... 14 Shock proof ................................. 15 Accessories ...............................16 Parts identification and handling .....................................16 Attaching to a tripod .................... 19 Using the LCD monitor ................ 20 SD card.......................................
VQT1D97(ENG).book 9 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products Others With a TV....................................75 Menus ........................................ 95 Playback on TV ........................... 75 Menu list ......................................95 Menus related to [SETUP] ...........97 With a DVD recorder .................77 Copying (dubbing) recordings onto a DVD recorder ................... 77 With a VCR.................................
VQT1D97(ENG).book 10 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using Before using Quick Guide 3 ∫ To insert/remove the battery. 1 Slide the card/battery door lock to OPEN and then open the card/ battery door. (To remove the battery) Slide the lock A in the direction of the arrow and then remove the battery. A BATT 4 ≥ When the card/battery door does not open, place your finger on the [ ] part and open the card/battery door.
VQT1D97(ENG).book 11 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using ∫ Charging the battery. ∫ How to turn on the power ≥ Set the mode dial to OFF. The battery cannot be charged when this unit is turned on. Set the mode dial to , , or . ≥ Align the desired symbol to the position shown in the illustration. Connect the AC adaptor (supplied) A to this unit and the AC outlet. 1 4.8V 3 A ∫ How to turn off the power Set the mode dial to OFF.
VQT1D97(ENG).book 12 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using 2 Insert/remove the SD card into/ from the card slot. 1 Press the record button to start recording. 2 Press the record button again to pause recording. A 3 ≥ When inserting an SD card, Place the label side A upwards and then press it straight in as far as it goes. ≥ When removing the SD card, press the center of the SD card and then pull it straight out. Close the card/battery door and then slide the card/battery door lock to LOCK.
VQT1D97(ENG).book 13 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using ∫ Motion picture playback ∫ Still picture playback ≥ Rotate the mode dial to select ≥ Rotate the mode dial to select . 1 Select the scene to be played back. 2 Press the cursor button in the center. 3 Press the cursor button to operate. 1/;: Playback/Pause :: Skip playback (backward) 9: Skip playback (forward) ∫: Stops the playback and shows the thumbnails. . 1 Select the file to be played back.
VQT1D97(ENG).book 14 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using Features Water resistance This unit is a water-resistant video camera complying with the IPX4 specifications* of the IEC 60529 “Degrees of protection provided by enclosures (IP Code)”. Holding this unit with wet hands or some water splashing onto it will not cause it to malfunction, but this unit cannot be used underwater. * Water may be splashed onto this unit from any direction without causing it to malfunction.
VQT1D97(ENG).book 15 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using Shock proof This unit is a high shock-proof video camera that passed a drop test* from a height of 1.2 m (4 feet). * This test confirmed to “MIL-STD 810F Method 516.5 – Shock”. (The product was dropped on top of 5 cm (2z) thick plywood.) This does not guarantee that the unit will not be damaged or malfunction.
VQT1D97(ENG).book 16 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using Accessories Check the accessories before using this unit.
VQT1D97(ENG).
VQT1D97(ENG).book 18 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using ∫ About the Card/battery door and the Terminal cover 23 24 25 26 27 28 23 Terminal cover 24 Terminal cover lock [LOCK 21 OPEN] (l 75, 78, 79, 88) 25 Audio-video output terminal [A/V] (l 75, 78) 26 USB terminal [ ] (l 80, 89) 27 DC input terminal [DC IN 4.8V] (l 25) 28 Sub record button (l 43) ≥ This button makes it easier to record from a non-standard or lower position, for example at waist level.
VQT1D97(ENG).book 19 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using Attaching to a tripod Strap fixture We recommend using the 2-way hand strap (supplied) to prevent the unit from dropping. Attach the 2-way hand strap 1 to this unit. 1 ∫ To use as a grip belt. 1 Attach the tripod adaptor 2 to the attachment screw for tripod adaptor on this unit. To use a tripod (optional), the tripod adaptor on the 2-way hand strap (supplied) must be attached to this unit.
VQT1D97(ENG).book 20 ページ ２００７年３月２０日 Before using Using the LCD monitor You can record the image while viewing it on the LCD monitor. 1 Place your finger on the LCD monitor open part A and pull the LCD monitor out in the direction of the arrow. A ≥ It can open up to 90o. 2 Adjust the angle of the LCD monitor as desired. ≥ It can rotate up to 90o A towards the lens or 90o B towards the opposite direction. A B ≥ The brightness and color level of the LCD monitor can be adjusted from the menu.
VQT1D97(ENG).book 21 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using SD card This unit can be used for recording motion pictures and still pictures to an SD card. Concerning the cards that can be used on this unit SDHC Memory Card SD Memory Card Capacity Recording motion pictures Recording still pictures 8 MB, 16 MB 32 MB, 64 MB, 128 MB – ¥*1 256 MB, 512 MB 1 GB, 2 GB 4 GB ¥*2 ¥ ¥: available –: not available *1 Cannot be guaranteed in operation.
VQT1D97(ENG).book 22 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using ≥ When the write-protect switch A on SD card is locked, no recording, deleting or editing will be possible on the card. A ∫ About SD cards that you can use for motion picture recording. We recommend using SD cards conforming to Class 2 or higher of the SD Speed Class Rating or the following SD cards made by Panasonic for motion picture recording.
VQT1D97(ENG).book 23 ページ ２００７年３月２０日 火曜日 午後５時３３分 Before using ∫ Handling precautions ≥ Do not touch the terminals on the back of the card. ≥ Do not expose the terminals of the card to water, garbage or dust. ≥ Do not place in the following areas: jIn direct sunlight. jIn very dusty or humid areas. jNear a heater. jLocations susceptible to significant difference in temperature (condensation can occur). jWhere static electricity or electromagnetic waves occur.
VQT1D97(ENG).book 24 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Setup Power supply 2 Insert the battery until it clicks paying attention to the direction of the battery. 3 Close the card/battery door and then slide the card/battery door lock to LOCK. Inserting the battery and charging the battery When this unit is purchased, the battery is not charged. Charge the battery before using this unit. ¬ Rotate the mode dial to select OFF. ≥ The battery will not be charged if the power is turned on.
VQT1D97(ENG).book 25 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup 4 1 Connect the AC adaptor (supplied) A to this unit and the AC outlet. B ≥ If you use other batteries, we cannot guarantee the quality of this product. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. ∫ About charging errors 4.
VQT1D97(ENG).book 26 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup When the status indicator is off: ≥ Charging is completed. ≥ When the status indicator does not flash, reinsert the battery or the AC adaptor. If the status indicator still does not flash, there may be a problem with the battery or the AC adaptor. Contact your dealer. 2 A ∫ Connecting to the AC outlet Be sure to set the mode dial to OFF when connecting the AC adaptor to this unit.
VQT1D97(ENG).book 27 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Charging time and recordable time The times shown in the tables below are for when the temperature is 25 oC (77 oF) and the humidity is 60%. If the temperature is higher or lower than 25 oC (77 oF), the charging time will become longer. ∫ Charging time Battery model number Voltage/capacity Charging time Supplied battery/ VW-VBJ10 (optional) 3.6 V/1000 mAh 2 h 10 min ≥ The charging time shown in the table are approximations.
VQT1D97(ENG).book 28 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Selecting a mode How to turn off the power Set the mode dial to OFF. Selecting a mode (Turning the unit on/off) Rotate the mode dial to video recording, video playback, picture recording, picture playback or power OFF. Rotate the mode dial slowly but surely. How to turn on the power Set the mode dial to or . , , ≥ Align the desired symbol to the position shown in the illustration.
VQT1D97(ENG).book 29 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup How to turn the power on and off with the LCD monitor The power can be turned on and off with the LCD monitor when the mode dial is set to or . ∫ To turn on the power Open the LCD monitor. The status indicator lights and the power turns on. ∫ To turn off the power Close the LCD monitor. Quick start When quick start is ON the battery power is still being consumed, even when the LCD monitor is closed.
VQT1D97(ENG).book 30 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup 2 Close the LCD monitor while the mode dial is set to or . A The status indicator A flashes green and the unit goes into quick start standby mode. 3 Open the LCD monitor. A The status indicator A lights red and the unit is put into recording pause approx. 1.7 seconds after it is turned on. To cancel Quick start Press the MENU button then [SETUP] # [QUICK START] # [OFF] and then press the cursor button in the center.
VQT1D97(ENG).book 31 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Inserting/removing an SD card 3 Insert/remove the SD card into/from the card slot. Be sure to set the mode dial to OFF before inserting/removing an SD card. If the SD card is inserted or removed while the power is on, this unit may malfunction or the data recorded on the SD card may be lost. 1 ≥ Check that the status indicator has gone off. 2 A Set the mode dial to OFF.
VQT1D97(ENG).book 32 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup ∫ Card access lamp ≥ When this unit accesses the SD card (reading, recording, playback, erasing, etc.), the access lamp lights up. ≥ If the following operations are performed when the access lamp is lit, then the SD card or the recorded data may be damaged or this unit may malfunction.
VQT1D97(ENG).book 33 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Operations during recording ¬ Rotate the mode dial to select or . 1 Press the cursor button in the center and the icons will be displayed on the screen. Operations during playback ¬ Rotate the mode dial to select or . 1 Press the cursor button up, down, left or right to select the scene to be played back and then press the cursor button in the center. 1/2 NEXT ≥ The indication disappears when the cursor button in the center is pressed again.
VQT1D97(ENG).book 34 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup About the operation icons displayed in each mode About auto mode and manual mode (l 44) Video recording mode 1/2 NEXT 2/2 NEXT Icon (1/2) (2/2) (3/3) When the [MANUAL AF/MF] button is pressed to set to manual mode. (4/4) When the [MANUAL AF/MF] button is pressed again to set to manual focus mode.
VQT1D97(ENG).
VQT1D97(ENG).book 36 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Picture recording mode 1/2 NEXT 2/2 NEXT Icon 3/3 NEXT 4/4 NEXT Direction Function Page 3 Backlight compensation 51 2 Self timer 54 1 Help mode 37 (2/2) 2 Soft skin mode 53 (3/3) When the [MANUAL AF/MF] button is pressed to set to manual mode.
VQT1D97(ENG).book 37 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup ∫ Help mode The help mode explains the operation icons that are displayed when the unit is set to AUTO in video/picture recording mode. ≥ Rotate the mode dial to select or . 1 Press the cursor button in the center to display the icon during the recording pause. ≥ When the help mode is used, functions cannot be set. ≥ When the help mode is used, motion pictures and still pictures cannot be recorded.
VQT1D97(ENG).book 38 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup Switching the language Using the menu screen You can switch the language on the screen display or the menu screen. Refer to “Menu list” (l 95) for information about the menus. 1 1 2 Press the MENU button, then select [LANGUAGE] and then press the cursor button in the center. Select [English] and then press the cursor button in the center. 38 VQT1D97 While stopped, press the MENU button.
VQT1D97(ENG).book 39 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup 4 Press the cursor button up or down in order to select the submenu item. To get back to the previous screen Press the cursor button left. To exit the menu screen 5 Press the MENU button. Press the cursor button right or press the cursor button in the center. ≥ The menu screen does not appear during recording or playing. You cannot start other operations while the menu screen appears.
VQT1D97(ENG).book 40 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup ≥ The 12-hour system is used to display the time. Setting date and time When the unit is turned on for the first time, a message asking you to set the date and time will appear. ≥ Select [YES] and press the cursor button in the center. Perform steps 2 and 3 below to set the date and time. If the screen shows the incorrect date and time, then adjust it. ¬ Rotate the mode dial to select or .
VQT1D97(ENG).book 41 ページ ２００７年３月２０日 火曜日 午後５時３３分 Setup ∫ Changing the display style Press the MENU button, then select [SETUP] # [DATE FORMAT] # desired display style and press the cursor button in the center. Display style Screen display [Y/M/D] 2007.DEC.15 [M/D/Y] DEC.15.2007 [D/M/Y] 15.DEC.2007 Adjusting the LCD monitor Adjusting the brightness and color level 1 Press the MENU button, then select [SETUP] # [LCD SET] # [YES] and then press the cursor button in the center.
VQT1D97(ENG).book 42 ページ ２００７年３月２０日 Setup ≥ These settings will not affect the images actually recorded. Increasing and decreasing the brightness of the entire LCD monitor Press the MENU button, then select [SETUP] # [POWER LCD] # [ON] and then press the cursor button in the center. The [ ] indication appears on the LCD monitor. ≥ Set [POWER LCD] to [ON] if the surroundings are bright and the LCD monitor is difficult to see. The entire LCD monitor will become approx. twice as bright as usual.
VQT1D97(ENG).book 43 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Recording Before recording First, format the SD card if one which has been used on another device is going to be used for the first time on this unit. (l 74) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Copy valuable data onto a computer or other device before proceeding with the formatting. We recommend using MotionSD STUDIO etc. to import data recorded on this unit.
VQT1D97(ENG).book 44 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording ≥ This unit has lens-protecting glass to prevent drops of water getting in the lens. If there is dirt or drops of water on the lens-protecting glass, wipe them off before recording. We recommend using the cleaning cloth. ≥ If there are drops of water on the microphone, the recorded sound will be distorted. Wipe off any drops of water on the microphone. ≥ When you are outdoors, record pictures with the sunlight behind you.
VQT1D97(ENG).book 45 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Recording motion pictures ≥ When the unit is purchased, the aspect ratio is set to [16:9] for recording images compatible with a wide-screen TV. To watch images on a regular TV (4:3), change the aspect ratio setting (l 55) before recording the images or when watching them on the connected TV (l 76). ≥ Use an SD card that can be used for motion picture recording. (l 22) 1 Rotate the mode dial to select .
VQT1D97(ENG).book 46 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Screen indications in the video recording mode A SP R 1h30m B C 0h00m10s A Recording mode B Remaining time left for recording (When the remaining time is less than 1 minute, [R 0h00m] flashes red.) C Recording time elapsed ≥ Sound is recorded from the internal stereo microphone on the front of the unit. Take care not to block this microphone. ≥ If the write protection switch on the SD card is set to LOCK, it cannot be used for recording.
VQT1D97(ENG).book 47 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Recording modes and recordable time available for the motion picture Changing the recording mode of the motion picture. ¬ Rotate the mode dial to select . Press the MENU button, then select [BASIC] # [REC MODE] # desired item and then press the cursor button in the center.
VQT1D97(ENG).book 48 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Recording still pictures ≥ Still pictures are recorded at a picture size of 640k480 pixels on this unit. 1 Rotate the mode dial to select 2 Press the record button. . The unit automatically focuses on the subject at the center of screen (when auto focus is selected). ≥ For information about the number of recordable still pictures (l 120) ≥ The sound cannot be recorded.
VQT1D97(ENG).book 49 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Screen indications in picture recording mode A 0.3M R 12345 B C A Size of still pictures B Remaining number of still pictures (Flashes in red when [R 0] appears.) C Quality of still pictures Recording with a shutter operation effect You can add a shutter sound when recording still pictures. Press the MENU button, then select [ADVANCED] # [SHTR EFFECT] # [ON] and then press the cursor button in the center.
VQT1D97(ENG).book 50 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Various recording functions Zoom in/out function You can zoom in up to 10k optically. ¬ Rotate the mode dial to select or . Press the zoom button. ≥ When the zoom speed is high, the subject may not be focused easily. ≥ When zooming in while holding this unit by hand, we recommend using the image stabilizer function. (l 56) ≥ When distant subjects are brought closer, they are focused at about 1.0 m (3.3 feet) or more.
VQT1D97(ENG).book 51 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording To use the zoom microphone function The zoom microphone is linked to the zooming operation so that far-away sounds with a tele-shot and close-up sounds with a wide-angle shot are recorded more clearly. ¬ Rotate the mode dial to select . Press the MENU button, then select [ADVANCED] # [ZOOM MIC] # [ON] and then press the cursor button in the center. Backlight compensation function This is for protecting a backlit subject from being darkened.
VQT1D97(ENG).book 52 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Fade in/fade out function When you start recording, the image/ audio gradually appears. Pause recording. (Fade out) Fade in: The image and audio gradually appear. Fade out: The image and audio gradually disappear. ¬ Rotate the mode dial to select . 1 Press the cursor button in the center. Then press the button down to display the icon shown in the illustration. The image/audio gradually disappears.
VQT1D97(ENG).book 53 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording MagicPix function This allows recording in dark locations. This function allows you to record color subjects in dark locations to stand out against the background. Attach this unit to a tripod and you can record images free from vibration. ≥ Minimum required illumination: approx. 2 lx ≥ Recorded scene is seen as if frames were missed. ¬ Rotate the mode dial to select . 1 Press the cursor button in the center.
VQT1D97(ENG).book 54 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording 2 down to display the icon shown in the illustration. Press the cursor button left to select [ ]. 1/2 NEXT 2/2 NEXT To cancel the soft skin mode Select [ 2 ] again. ≥ If the background or anything else in the scene has colors similar to the skin color, they will also be smoothed. ≥ If the brightness is insufficient, the effect may not be clear. ≥ You may not be able to see the face clearly when recording a distant person.
VQT1D97(ENG).book 55 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Recording guideline function Checking if the image is level. You can check if the image is level while recording by using the lines displayed on the screen. ¬ Rotate the mode dial to select or . Press the MENU button, then select [BASIC] # [GUIDE LINES] # [ON] and then press the cursor button in the center. Wide mode This is for selecting the screen’s aspect ratio when recording motion pictures.
VQT1D97(ENG).book 56 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Image stabilizer function This is for reducing image shakes (jitter) during recording. Reduces the image shaking (jitter) due to hand movement when recording. ¬ Rotate the mode dial to select . Press the MENU button, then select [ADVANCED] # [EIS] # [ON] and then press the cursor button in the center.
VQT1D97(ENG).book 57 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Wind noise reduction function This is for reducing the wind noise coming into the microphone when recording. ¬ Rotate the mode dial to select . Press the MENU button, then select [ADVANCED] # [WIND CUT] # [ON] and then press the cursor button in the center. Manual recording functions Scene mode This is for recording in various situations.
VQT1D97(ENG).
VQT1D97(ENG).book 59 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording ≥ The subject may not be in focus when zoomed in if focusing with a wide angle. First, zoom in on the subject and then focus on it. Manual focus adjustment If auto focusing is difficult due to the conditions, then manual focusing is available. ¬ Rotate the mode dial to select or . 1 Press the MANUAL AF/MF button until the icon shown in the illustration below is displayed.
VQT1D97(ENG).book 60 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording White balance This is for recording in natural colors. The automatic white balance function may not reproduce natural colors depending on the scenes or lighting conditions. If so, you can adjust the white balance manually. ¬ Rotate the mode dial to select or . 1 Press the MANUAL AF/MF button. MNL 3/3 NEXT The icon shown in the illustration is displayed automatically. 2 Press the cursor button up to select [ ].
VQT1D97(ENG).book 61 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording To set the white balance manually 1 Select [ ] and then fill the screen with a white subject. MNL BACK BACK 2 Do not cover the white balance sensor during recording or it may not function properly. ≥ When the [ ] display flashes, the manual white balance previously adjusted is stored. Whenever recording conditions change, re-set the white balance for correct adjustment.
VQT1D97(ENG).book 62 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording Manual shutter speed/ aperture adjustment Shutter Speed: Adjust it when recording fast-moving subjects. Aperture: Adjust it when the screen is too bright or too dark. ¬ Rotate the mode dial to select or . 1 Press the MANUAL AF/MF button. MNL 3/3 NEXT The icon shown in the illustration is displayed automatically. 2 Press the cursor button on the left or right to select [ ] (aperture) or [ ] (shutter speed).
VQT1D97(ENG).book 63 ページ ２００７年３月２０日 火曜日 午後５時３３分 Recording ∫ Manual shutter speed adjustment ≥ Avoid recording under fluorescent light, mercury light or sodium light because the color and brightness of the playback image may change. ≥ If you increase the shutter speed manually, the gain value will increase automatically depending on how much the sensitivity lowers and the noise on the screen may increase.
VQT1D97(ENG).book 64 ページ ２００７年３月２０日 火曜日 午後５時３３分 Playback Playback Motion picture playback Play back the motion pictures. 1 Rotate the mode dial to select . The motion pictures (up to 8 scenes) recorded on the SD card are displayed as thumbnails. 2 Select the scene to be played back. A Scene number B Scroll bar display The selected scene will be encircled by a yellow frame.
VQT1D97(ENG).book 65 ページ ２００７年３月２０日 火曜日 午後５時３３分 Playback ∫ About motion picture compatibility ≥ This unit can play back MPEG2 formatted files. ≥ This unit is based on the SD-Video standard. ≥ When playing back motion pictures recorded on an SD card with other products on this unit or playing back motion pictures recorded on an SD card with this unit on other products, the picture quality may deteriorate and they may be unplayable. (The message “CANNOT PLAY.” appears.
VQT1D97(ENG).book 66 ページ ２００７年３月２０日 火曜日 午後５時３３分 Playback Frame-by-frame playback The motion picture is advanced one frame at a time. 1 Press the cursor button up during playback to pause the playback. 2 Press the cursor button right. (The frames will be advanced one at a time in the reverse direction when you press the cursor button left.) ≥ Normal playback is restored when you press the cursor button up. To adjust the volume Adjust the speaker volume during playback.
VQT1D97(ENG).book 67 ページ ２００７年３月２０日 火曜日 午後５時３３分 Playback 2 Press the cursor button up or down to select the date for playback, then press the cursor button in the center. The scenes recorded on the same day are displayed as thumbnails. 3 Select the scene to be played back. ≥ The playback setting returns to [VIEW ALL] if the unit is turned off or the mode dial is operated. ≥ Even if scenes are recorded on the same day, they are grouped separately when the number of scenes exceeds 99.
VQT1D97(ENG).book 68 ページ ２００７年３月２０日 火曜日 午後５時３３分 Playback Still picture playback Play back the still pictures. 1 Rotate the mode dial to select . The still pictures (up to 8 files) recorded on the SD card are displayed as thumbnails. 2 Select the file to be played back. A File number B Scroll bar display The selected file will be encircled by a yellow frame. ≥ When 9 or more files have been recorded, the next (or previous) page is displayed by pressing the cursor button up, down, left or right.
VQT1D97(ENG).book 69 ページ ２００７年３月２０日 火曜日 午後５時３３分 Playback ∫ About still picture compatibility ≥ This unit is compliant with the unified standard DCF (Design rule for Camera File system) established by JEITA (Japan Electronics and Information Technology Industries Association). ≥ The file format supported by this unit is JPEG. (Not all JPEG formatted files will be played back.) ≥ If a non-standard file is played back, the folder/file number may not be displayed.
VQT1D97(ENG).book 70 ページ ２００７年３月２０日 火曜日 午後５時３３分 Editing Editing Editing Deleting scenes This is for deleting scenes. The deleted scenes cannot be restored. Deleting multiple scenes from the thumbnail display ¬ Rotate the mode dial to select or . 1 Press the button in the thumbnail display. Deleting scenes one at a time ¬ Rotate the mode dial to select or . 1 Press the button during playback. 2 2 Select [ALL] or [SELECT] and then press the cursor button in the center.
VQT1D97(ENG).book 71 ページ ２００７年３月２０日 火曜日 午後５時３３分 Editing then press the cursor button in the center. ∫ Deleting still picture files recorded on an SD card by other products A still picture file (other than JPEG) that cannot be played back on this unit may be erased. The selected scene is encircled by a red frame. ≥ When the cursor button in the center is pressed again, the selected scene will be canceled. ≥ Up to 50 scenes can be set in succession.
VQT1D97(ENG).book 72 ページ ２００７年３月２０日 火曜日 午後５時３３分 Editing Locking scenes This is for preventing scenes from being deleted by mistake. 2 Select the scene to be locked, then press the cursor button in the center. Scenes can be locked so that they are not deleted by mistake. (Even if you lock some scenes on an SD card, formatting the SD card will delete them.) ¬ Rotate the mode dial to select or .
VQT1D97(ENG).book 73 ページ ２００７年３月２０日 火曜日 午後５時３３分 Editing DPOF setting This is for writing the printing data on an SD card. You can write the data of the still pictures to be printed and the number of prints (DPOF data) onto the SD card. ¬ Rotate the mode dial to select . 1 Press the MENU button, then select [PICT. SETUP] # [DPOF SET] # [SET] and then press the cursor button in the center. ≥ You can select from 0 to 999. (The selected number of pictures can be printed with the printer supporting DPOF.
VQT1D97(ENG).book 74 ページ ２００７年３月２０日 火曜日 午後５時３３分 Editing Card management Formatting an SD card This is for initializing cards. Please be aware that if an SD card is formatted, then all the data recorded on the card will be erased. Store important data on a computer, etc. We recommend using MotionSD STUDIO etc. to acquire data recorded on this unit. (l 82) 1 Press the MENU button, then select [SETUP] # [FORMAT CARD] # [YES] and then press the cursor button in the center.
VQT1D97(ENG).book 75 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products With other products With a TV Playback on TV The motion pictures and still pictures recorded by this unit can be played back on a TV. ≥ Use the AC adaptor to free you from worrying about the battery running down. 1 Slide the terminal cover lock to OPEN and then open the terminal cover. 3 Rotate the mode dial to select or . 4 Change the input channel on the TV.
VQT1D97(ENG).book 76 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products ∫ To watch images with a 16:9 aspect ratio on a regular TV (4:3) ∫ To display the on-screen information on the TV screen When playing back motion pictures recorded with a 16:9 aspect ratio ([ASPECT] was set to [16:9]) on a TV with a 4:3 aspect ratio, the images may be squeezed horizontally. In this case, change the menu setting to play back the pictures in the original aspect ratio.
VQT1D97(ENG).book 77 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products With a DVD recorder Copying (dubbing) recordings onto a DVD recorder If you have a DVD recorder with an SD card slot, images recorded by this unit can be copied (dubbed) onto the hard disk or a DVD disc. Refer to the operating instructions of your DVD recorder for information about whether or not it supports copying (dubbing) from an SD card.
VQT1D97(ENG).book 78 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products With a VCR 2 Connect this unit and a video device. Recording (dubbing) images onto other video devices You can record (dub) images played back on this unit onto other video devices. ≥ Use the AC adaptor to free you from worrying about the battery running down. 1 VIDEO IN AUDIO IN A Slide the terminal cover lock to OPEN and then open the terminal cover. A AV cable (supplied) ≥ Insert the plugs as far as they will go.
VQT1D97(ENG).book 79 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products To stop recording (dubbing) Stop recording on the connected device. Then stop playback on this unit. ≥ If the date and time display and function indication are unnecessary, cancel them before recording (dubbing). (l 40, 76) With a printer (PictBridge) To print pictures by directly connecting this unit to the printer, use a printer compatible with PictBridge. (Read the operating instructions for the printer.
VQT1D97(ENG).book 80 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products 2 Connect this unit to a printer. 4 Select a file to be printed, then press the cursor button in the center. A The number of pictures set is displayed. 5 A USB cable (supplied) ≥ Insert the plugs as far as they will go. ≥ Do not use any other USB connection cables except the supplied one. (Operation is not guaranteed with any other USB cables.
VQT1D97(ENG).book 81 ページ ２００７年３月２０日 火曜日 午後５時３３分 With other products 8 Select the paper size setting on [PAPER SIZE]. ≥ Exit PictBridge by disconnecting the USB cable after the pictures have been printed. When you want to stop printing halfway [STANDARD]: Size specific to the printer [4t5 INCH]: L size [5t7 INCH]: 2L size [4t6 INCH]: Postcard size [A4]: A4 size ≥ You cannot set paper sizes not supported on the printer. 9 Select the layout setting on [PAGE LAYOUT].
VQT1D97(ENG).book 82 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer With a computer With a computer (Windows) What you can do with a computer When the CD-ROM (supplied) is inserted into the computer, the [Setup Menu] screen will appear. ∫ Video editing software MotionSD STUDIO 1.2E This software allows pictures to be acquired from this unit, edited and output. You can also send a picture acquired from this unit by e-mail and edited pictures can be written to the DVD drive.
VQT1D97(ENG).book 83 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Before opening the CD-ROM package, please read the following. End User License Agreement You (“Licensee”) are granted a license for the Software defined in this End User License Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee does not agree to the terms and conditions of this Agreement, promptly return the Software to Matsushita Electric Industrial Co., Ltd.
VQT1D97(ENG).book 84 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Operating environment ≥ A CD-ROM drive is necessary to install the supplied software. ≥ When 2 or more USB devices are connected to a computer, or when devices are connected through USB hubs or by using extension cables, proper operation is not guaranteed. ≥ Use the supplied USB cable when connecting to the computer. (Operation is not guaranteed with any other USB cables.
VQT1D97(ENG).book 85 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Disc drive CD-ROM drive (When writing to DVD, a compatible drive and media are necessary.) Interface USB port (Hi-Speed USB (USB 2.0) recommended) Other requirements Mouse or equivalent pointing device ≥ The supplied CD-ROM is available for Windows only. ≥ Operation is not guaranteed on computers that are not IBM PC/AT compatible. ≥ This software is not compatible with a multi-boot environment.
VQT1D97(ENG).book 86 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Installing MotionSD STUDIO When installing the software, log on to your computer as the Administrator or with a user name with equivalent authorization. (If you do not have authorization to do this, consult your manager.) ≥ Before starting the installation, close any other software applications which are running. ≥ Do not perform any other operations on your computer while the software is being installed.
VQT1D97(ENG).book 87 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer 5 After the installation is complete, [Readme.txt] are displayed. Check the contents, then click [t] on top right of the window. 6 Click [Finish]. cable, the [SD Browser auto start] screen appears for starting MotionSD STUDIO. (l 89) ≥ Depending on the operating environment, you may be required to install DirectX 9.0b. If so, click [Yes] and install it.
VQT1D97(ENG).book 88 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Reading the MotionSD STUDIO operating instructions For details on how to use MotionSD STUDIO, read the PDF instructions. Select [start]> [All Programs (Programs)]> [Panasonic]> [MotionSD STUDIO 1.2E]> [Manual]. ≥ After starting the software, on the menu select [Help]>[Manual] to display the help files. ≥ You will need Adobe Acrobat Reader 5.0 or later version to read the PDF operating instructions.
VQT1D97(ENG).book 89 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer 3 Connect this unit and a computer. A 4 Press the cursor button up or down to select [PC CONNECT], then press the cursor button in the center. 5 The [SD Browser auto start] screen appears. ≥ If [Yes] is clicked, MotionSD STUDIO starts. (l 92) ≥ Click [No] if you do not want to start MotionSD STUDIO. A USB cable (supplied) ≥ Insert the plugs as far as they will go.
VQT1D97(ENG).book 90 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Verifying that the unit is correctly recognized by the computer To verify if this unit is correctly recognized by the computer, turn on this units power and then connect the unit to the computer with a USB cable and follow the steps below. ≥ With some computers including those made by NEC, the Device Manager may not be displayed if a mode that places restrictions on the functions has been established.
VQT1D97(ENG).book 91 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer About the computer display When the unit is connected to a computer, it is recognized as an external drive. ∫ Drive icons [Removable Disk] is displayed in [My Computer]. ≥ Windows XP: ≥ Windows 2000: ≥ Up to 999 files can be recorded in the [100CDPFP] or other such folder. ≥ The DPOF setting files are recorded in the [MISC] folder. ≥ Do not use the computer to delete the SD card’s folders.
VQT1D97(ENG).book 92 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer Using MotionSD STUDIO ≥ Before initial use, select the software [Readme First] from the start menu, then read through the additional instructions or updated information. ≥ The End User Licence Agreement is displayed when the software is first started, so read carefully through its terms and conditions, then click [I agree]. ≥ When using MotionSD STUDIO 1.2E, log on to your computer as Administrator with a login name equally authorized.
VQT1D97(ENG).book 93 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer To disconnect the USB cable safely 1 Double click the icon in the task tray displayed on the computer screen. Software uninstallation Follow the steps below to uninstall the software if it is no longer required. 1 Select [start] # ([Settings] #) [Control Panel] # [Add or Remove Programs (Applications)]. 2 Select [MotionSD STUDIO 1.2E], then click [Change/ Remove] ([Change or Remove] or [Add/Remove]).
VQT1D97(ENG).book 94 ページ ２００７年３月２０日 火曜日 午後５時３３分 With a computer With a computer (Macintosh) Operating environment ≥ Even if the system requirements mentioned in these operating instructions are fulfilled, some computers cannot be used. ≥ Apple and Mac OS are trademarks of Apple Inc. ≥ PowerPC is a trademark of International Business Machines Corporation.
VQT1D97(ENG).book 95 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Others Menus Still picture recording menus Menu list Motion picture recording menus ∫ [BASIC] [SCENE MODE] (l 57) [GUIDE LINES] (l 55) [PICT. QUALITY] (l 49) [CLOCK SET] (l 40) ∫ [BASIC] [SCENE MODE] (l 57) [GUIDE LINES] (l 55) [REC MODE] (l 47) [ASPECT] (l 55) [CLOCK SET] (l 40) ∫ [ADVANCED] [D.
VQT1D97(ENG).book 96 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Motion picture playback menus Still picture playback menus ∫ [PLAY SETUP] [PLAY MODE] (l 66) [RESUME PLAY] (l 67) [LOCK SET] (l 72) ∫ [PICT. SETUP] [LOCK SET] (l 72) [DPOF SET] (l 73) ∫ [SETUP] [DISPLAY] (l 97) [DATE/TIME] (l 40) [DATE FORMAT] (l 41) [FORMAT CARD] (l 74) [POWER SAVE] (l 97) [BEEP SOUND] (l 97) [POWER LCD] (l 42) [LCD SET] (l 41) [TV ASPECT] (l 76) [EXT.
VQT1D97(ENG).book 97 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Menus related to [SETUP] ∫ [DISPLAY] ≥ [OFF] ≥ [ON] The screen indications are selected as shown in the illustration below. [OFF] SP R 1h30m 1 Beep When you start recording When you turn on the power When this unit is recognized by the computer or the printer, etc. ; 0h00m00s 2 Beeps When you pause recording When you turn off the power DEC.15.
VQT1D97(ENG).book 98 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Indications ∫ [DEMO MODE] ≥ [OFF] ≥ [ON] This item is used to start the unit demonstration. (Only when using the AC adaptor and the mode dial is at the or position) If you set this to [ON] without inserting an SD card, this unit is automatically set to the demonstration mode for introducing its functions. If buttons other than the Mode select buttons [AUTO]/[MANUAL AF/MF] are pressed or operated, the demonstration mode is canceled.
VQT1D97(ENG).book 99 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Backlight compensation ª Image stabilizer 1/100 Shutter speed OPEN, F2.
VQT1D97(ENG).book 100 ページ ２００７年３月２０日 Others When a printer compatible with PictBridge is connected Accessing the card (When connected to a computer) 001 DPOF already set (to more than 1) Locked motion pictures and still pictures 0.3M Number of recording pixels for still pictures 640k480 The picture size is not displayed for still pictures recorded with other products that have different picture sizes from the size shown above.
VQT1D97(ENG).book 101 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Messages CANNOT RECORD. Data writing to the SD card has failed. NO DATA. There are no motion pictures or still pictures recorded on the SD card. If this message appears although data is recorded on the SD card, the condition of the card is probably not stable. Turn off the power and then turn it on again. THIS CARD CANNOT RECORD IN VIDEO MODE. An 8 MB or 16 MB SD card has been inserted in video recording mode. CHECK CARD.
VQT1D97(ENG).book 102 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others EXIT THE MENU THEN CHANGE TO MANUAL MODE. You are attempting to use a function that cannot be used simultaneously. CANCEL MAGICPIX MODE. PLEASE CONNECT AC ADAPTOR You are attempting to connect to a computer when the AC adaptor is not connected. PUSH THE RESET SWITCH. An irregularity in the unit has been detected. Remove the SD card then press the RESET button to restart the unit. (l 109) DISCONNECT USB CABLE.
VQT1D97(ENG).book 103 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Functions that cannot be used simultaneously Some functions in this unit are disabled or cannot be selected due to the unit’s specifications. The table below shows examples of functions restricted by various conditions.
VQT1D97(ENG).book 104 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Troubleshooting Problem Check points This unit cannot be turned on. The status indication flashes when the unit is turned on while using the battery. ≥ Is the battery fully charged? # Charge the battery using the AC adaptor. (l 25) This unit is turned off automatically. ≥ If you do not use the unit for approximately 5 minutes, the power is automatically turned off to conserve the battery charge. To resume recording, turn the power back on.
VQT1D97(ENG).book 105 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Problem This unit cannot be operated though it is turned on. This unit does not operate normally. Check points ≥ The unit cannot be operated unless you open the LCD monitor. ≥ Remove the SD card then press the RESET button. (l 109) If normal conditions are not restored yet, remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the power again.
VQT1D97(ENG).book 106 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Problem Check points Recording does not start although the power is supplied to this unit and the SD card is correctly inserted. ≥ Has the SD card’s write protect switch been set to LOCK? # No recording is possible while the write protect switch is set to LOCK. (l 22) ≥ Is the memory of the card full? # If the card has no more available memory, free up some memory by deleting unnecessary scenes (l 70) or use a new card.
VQT1D97(ENG).book 107 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Problem Check points Auto focus function does not work. ≥ Is manual focus mode selected? # Set the unit to auto focus mode by pressing the AUTO button. ≥ Are you trying to record a scene which is hard to bring into focus in auto focus mode? # There are some recording subjects and surroundings for which the auto focus does not operate correctly. (l 115) If so, use the manual focus mode to adjust the focus.
VQT1D97(ENG).book 108 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Problem Check points Scenes or files cannot be deleted or edited. ≥ Are the scenes or the files locked? # Locked scenes or files cannot be deleted. Release the lock setting. (l 72) ≥ It may not be possible to delete scenes that are displayed as [ ] on the thumbnail display. If the scenes are unnecessary, format the card to erase the data. (l 74) Please be aware that if the card is formatted then all the data recorded on the card will be erased.
VQT1D97(ENG).book 109 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Problem Check points ≥ The unit has automatically detected an error. To protect the data, remove the SD card and then press the RESET button with a pointed object. This will restart the unit. “PUSH THE RESET SWITCH.” is displayed. ≥ If you do not press the RESET button, the power to this unit is turned off automatically about 1 minute later. ≥ Even after you press the RESET button, the indication may still appear repeatedly.
VQT1D97(ENG).book 110 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others With a computer Problem Check points Even if connected by the USB cable, this unit is not recognized by the computer. ≥ The USB function selection screen does not appear if the USB cable is connected while the menu screen is displayed. # Close the menu screen before connecting the USB cable. ≥ Is the AC adaptor connected? # Use the AC adaptor when connecting the unit and a computer. ≥ Select another USB terminal on the computer.
VQT1D97(ENG).book 111 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Cautions for use About this unit ≥ The unit and card become warm after long operation, but this is not a malfunction. Keep the SD Video Camera as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). ≥ If you use the SD Video Camera on top of or near a TV, the pictures and sound on the SD Video Camera may be disrupted by electromagnetic wave radiation.
VQT1D97(ENG).book 112 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others ≥ Wipe the unit with a soft dry cloth to remove dust and fingerprints. To remove stubborn stains, thoroughly wring a cloth that has been soaked in a neutral detergent diluted with water and wipe the unit with it. Afterwards, wipe it with a dry cloth. ≥ When you use a chemical dust cloth, follow the instructions that came with the cloth. Do not use the unit for surveillance purposes or other business uses.
VQT1D97(ENG).book 113 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others If you drop the battery accidentally, check to see if the terminals are damaged. ≥ Attaching a battery with damaged terminals can damage the unit. Do not throw old batteries into fire. ≥ Heating a battery or throwing it into a fire may result in an explosion. If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery.
VQT1D97(ENG).book 114 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others LCD monitor ≥ When the LCD monitor gets dirty, wipe it with a dry soft cloth. ≥ In a place with drastic temperature changes, condensation may form on the LCD monitor. Wipe it with a soft dry cloth. ≥ When the unit has become very cold, for example due to storage in a cold area, its LCD monitor will be slightly darker than usual immediately after the power is turned on.
VQT1D97(ENG).book 115 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Explanation of terms Automatic white balance White balance adjustment recognizes the color of light and adjusts so the white color will become a purer white. The unit determines the hue of light that comes through the lens and white balance sensor, thereby judging the recording condition, and selects the closest hue setting. This is called automatic white balance adjustment.
VQT1D97(ENG).book 116 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others ≥ Attempts to bring an object with higher contrast into focus. ≥ Focuses on the screen center only. The unit cannot focus correctly because the light information that comes through the lens decreases considerably. Due to these characteristics, auto focus does not work correctly in the following situations. Record pictures in the manual focus mode.
VQT1D97(ENG).book 117 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Specifications SD Video Camera Information for your safety Power source: Power consumption: DC 4.8 V (When using AC adaptor) DC 3.6 V (When using battery) Recording: 2.9 W Charging: 4.2 W Signal system EIA Standard: 525 lines, 60 fields NTSC color signal Image sensor 1/6z CCD image sensor Total: 680 K Effective pixels: Moving picture: 340 K (4:3), 300 K (16:9) Still picture: 350 K (4:3) Lens Auto Iris, F1.8 to F2.4 Focal length: 2.
VQT1D97(ENG).book 118 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others USB Card reader/writer function (No copyright protection support) Hi-Speed USB (USB 2.0) compliant, USB terminal Type miniB PictBridge-compliant Dimensions (excluding the projecting parts) 31 mm (W) k 63 mm (H) k 114 mm (D) [1.22z (W) k 2.48z (H) k 4.49z (D)] Mass (Weight) Approx. 182 g (0.40 lbs.) (without supplied battery and an SD card) Mass (Weight) in operation Approx. 204 g (0.45 lbs.
VQT1D97(ENG).book 119 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Still pictures Recording media SD Memory Card: 8 MB/16 MB/32 MB/64 MB/128 MB/256 MB/512 MB/1 GB/2 GB (FAT12 and FAT16 format corresponding) SDHC Memory Card: 4 GB (FAT32 format corresponding) Number of recordable pictures Refer to page 120. Compression JPEG (Design rule for Camera File system, based on Exif 2.
VQT1D97(ENG).book 120 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Number of recordable pictures on an SD card Picture size 0.3M (640k480) Picture quality 8 MB 37 75 16 MB 92 185 32 MB 200 410 64 MB 430 850 128 MB 820 1640 256 MB 1710 3410 512 MB 3390 6780 1 GB 6790 13580 2 GB 13820 27640 4 GB 27150 54290 ≥ The number of recordable pictures depends on whether [ together and on the subject being recorded. ≥ The numbers shown in the table are approximations.
VQT1D97(ENG).book 121 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Optional accessories Accessory No.
VQT1D97(ENG).book 122 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Accessory Order Form (For USA Customers) Please photocopy this form when placing an order. 1. Model # 2. Items Ordered Accessory # Description Price Each Quantity Total Price Subtotal Your State & Local Sales Tax Shipping & Handling 6.95 Total Enclosed 3. Method of payment (check one) Check of Money Order enclosed (NO C.O.D.
VQT1D97(ENG).book 123 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Request for Service Notice (USA Only) Please photocopy this form when making a request for service notice, in the unlikely event this product needs service. Request for Service Notice: •Please include your proof of purchase. (Failure to do so will delay your repair.) •To further speed your repair, please provide an explanation of what is wrong with the unit and any symptom it is exhibiting.
VQT1D97(ENG).book 124 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Limited Warranty (For USA Customers) PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA One Panasonic Way, Secaucus, New Jersey 07094 PANASONIC PUERTO RICO, INC. Ave. 65 de Infantería, Km. 9.
VQT1D97(ENG).book 125 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Carry-In, Mail-in (Prepaid) or In-Home Service For Carry-In, Mail-In (prepaid) or In-HomeService (as applicable) in the United States call toll free contact number listed above or visit Panasonic Web Site: http://www.panasonic.com For assistance in Puerto Rico call Panasonic Puerto Rico, Inc. (787)-750-4300 or fax (787)-768-2910.
VQT1D97(ENG).book 126 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Customer Services Directory Service in Canada: As per Service Center listed in Canadian warranty information l 127 Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: http://www.panasonic.com/consumersupport or, contact us via the web at: http://www.panasonic.
VQT1D97(ENG).book 127 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Warranty (For Canadian Customers) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.
VQT1D97(ENG).book 128 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others ∫ Numerics 2-way hand strap . . . . . . . . . . . . . . . 19 ∫ I Image stabilizer function . . . . . . . . . .56 Initial setting . . . . . . . . . . . . . . . . . . .97 Iris . . . . . . . . . . . . . . . . . . . . . . . . . . .62 ∫ A AC adaptor . . . . . . . . . . . . . 25, 26, 113 Adobe Acrobat Reader . . . . . . . . . . 82 Aperture . . . . . . . . . . . . . . . . . . . . . . 62 Auto focus . . . . . . . . . . . . . . . . . . .
VQT1D97(ENG).book 129 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others ∫ R Record button . . . . . . . . . . . . . . 45, 48 Recordable time . . . . . . . . . . . . . . . . 47 Recording modes . . . . . . . . . . . . . . . 47 Recording time elapsed . . . . . . . . . . 46 Recovery . . . . . . . . . . . . . . . . . . . . 102 Remaining number of still pictures . . . . . . . . . . . . . . . . . . . 49 Remaining time . . . . . . . . . . . . . . . . 46 Request for Service Notice (USA Only) . . . . . . . . . . . . . . . . . .
VQT1D97(ENG).book 130 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others Others Spanish Quick Use Guide/Guía española para el uso rápido 3 A ∫ Introducción/Remoción de la batería 1 BATT Deslice el cierre de la tapa de la tarjeta/batería hasta OPEN y abra la tapa de la tarjeta/batería. 4 ≥ Si la tapa de la tarjeta/batería no se abre. Ponga el dedo en la parte [ ] y abra la tapa de la tarjeta/batería. 2 (Para extraer la batería) Deslice el cierre A en la dirección de la flecha y extraiga la batería.
VQT1D97(ENG).book 131 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others ∫ Cambio de batería ∫ Cómo encender la unidad ≥ Coloque el selector de modo en OFF. La batería no se cargará si la cámara está conectada y en marcha. Ajuste el selector de modo en , , o . ≥ Alinee el pictograma del modo que desee seleccionar, en la posición indicada en la ilustración. Conecte el adaptador CA (suministrado) A a la cámara y a la toma de CA. 1 ∫ Cómo apagar la unidad Coloque el selector de modo en OFF. 4.
VQT1D97(ENG).book 132 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others 2 Inserte/quite la tarjeta SD en/de la ranura de la tarjeta. 1 Pulse el botón de grabación para iniciar la grabación. 2 Pulse el botón de grabación de nuevo para pausar la grabación. A ≥ Al introducir una tarjeta SD, ponga el lado de la etiqueta A hacia arriba y presiónela hasta el fondo. ≥ Para extraer la tarjeta SD, presione en el centro de la tarjeta y luego tire de ella derecho hacia fuera.
VQT1D97(ENG).book 133 ページ ２００７年３月２０日 火曜日 午後５時３３分 Others ∫ Reproducción de imágenes dinámicas ∫ Reproducción de imágenes fijas ≥ Gire el selector de modo para seleccionar . ≥ Gire el selector de modo para seleccionar . 1 Seleccione la escena a ser reproducida. 1 Seleccione el archivo a ser reproducido. 2 Pulse el cursor. 2 Pulse el cursor. 3 Mueva el cursor para realizar una de las siguientes operaciones. 3 Mueva el cursor para realizar una de las siguientes operaciones.
VQT1D97(ENG).
VQT1D97(ENG).
VQT1D97(ENG).book 136 ページ ２００７年３月２０日 火曜日 午後５時３３分 Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Panasonic Puerto Rico, Inc. Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 P VQT1D97 F0307My0 ( 1000 A ) © 2007 Matsushita Electric Industrial Co., Ltd.
