Operating Instructions

17
TQBJ0992
Note:
• Reset the clock regularly to maintain accuracy.
The sleep timer switches off the system after the set
time.
Press [SLEEP] repeatedly to select the setting (in
minutes).
To show the remaining time
Press [SLEEP].
Note:
• The sleep timer can be used together with the play timer.
• The sleep timer always comes first. Be sure not to set an
overlap of timers.
You can set the timer to come on at a certain time to
wake you up.
Preparation
Set the clock.
1 Press [CLOCK/TIMER] repeatedly to select
“Timer Adjust”.
2 Press [3, 4] to set the starting time (“On Time”)
and then press [OK].
3 Press [3, 4] to set the finishing time
(“Off Time”) and then press [OK].
4 Press [3, 4] to select the music source*
1
and
then press [OK].
Turning the timer on
1 Prepare the selected music source and set the
desired volume.
2 Press [F, PLAY].
“F” is shown.
To cancel, press [F, PLAY] again.
The system must be switched off for the timer to
operate.
To check the settings
Press [CLOCK/TIMER] repeatedly to select “Timer
Adjust”.
(During standby, press [CLOCK/TIMER] twice.)
Note:
• The timer starts at a low volume and increases gradually to
the preset level.
• The timer comes on at the set time every day if the timer is
on.
• If you switch off the system and switch on again while a
timer is in operation, the timer will not stop at the end time.
*1: “CD”, “USB”, “DAB+” ([PMX152]), and “FM” can be set as
the music source.
• For timer music source through the port for iPhone/
iPad/iPod and USB devices, select “USB”.
Firmware updates
Occasionally, Panasonic may release updated firmware
for this system that may add or improve the way a
feature operates. These updates are available free of
charge.
Preparation
• Turn this system on.
• Connect this system to the home network. (> 6)
– Make sure that the network is connected to the Internet.
1 Press [RADIO, EXT-IN] repeatedly to select
“NETWORK”.
2 Press [SETUP] repeatedly to select “FW Update”
and then press [OK].
3 Press [2, 1] to select “OK? Yes” and then press
[OK] to start the update.
• Select “OK? No” to cancel the update.
When the update begins, “Updating” is displayed.
The progress is displayed as “Upd %” while
updating. (“  ” stands for a number.)
4 After the update has finished, “Success” is
displayed.
Disconnect the AC mains lead and reconnect it
after 1 minute.
Note:
• If there are no updates, “No Need” is displayed.
• Downloading may take longer or may not work properly
depending on the connection environment.
Press [SETUP] repeatedly to select “FW Version”
and then press [OK].
The version of the installed firmware is displayed.
• Press [OK] to exit.
Others
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being used
for approximately 20 minutes.
To cancel this function
1 Press [SETUP] repeatedly to select “Auto Off”.
2 Press [2, 1] to select “Off” and then press [OK].
Note:
• To turn the function on, select “On” in step 2.
• This setting cannot be selected when radio is the source or
when “Net Standby” is “On”.
• If “Net Standby” is set to “On”, this function will also be set
to “On”. To change the setting, set “Net Standby” to “Off”.
(> 18)
• When connected to a Bluetooth
®
device, the function does
not work.
Sleep timer
Play timer
“30min” -. “60min” -. “90min” -. “120min”
^----------- “Off” (Cancel) (---------- b
You can also update the firmware from a pop-up
prompting you to do so on-screen within the app
“Panasonic Music Streaming” (> 9). For details on the
app, refer to the site below.
http://panasonic.jp/support/global/cs/audio/app/
(This site is in English only.)
Downloading takes approx. 10 minutes.
DO NOT DISCONNECT the AC mains
lead while one of the following
messages is displayed.
– “Updating” or “Upd %”
(“  ” stands for a number.)
• During the update process, no other operations can be
performed.
Checking the firmware version
Auto off function
SC-PMX152-150B_EGEBGN-TQBJ0992.book 17 ページ ２０２０年２月１２日 水曜日 午後３時３１分