Operating Instruction
7
RQT9995
7 Select your security options for this system.
To set the AirPlay password
1 Select “Yes” and then select “Next”.
2 Set your password and then select “Next”.
• You will need this password the next time this network
setting method is used.
• If you have performed a network reset (> 18)
, the
password will be cleared.
To skip this setting
Select “No” and then select “Next”.
• You can also change this setting after the network
connection is set up. (> 8, “To make network-related
settings”)
8 Select your network name (SSID) and type the
password.
• Check the wireless router for the network name (SSID)
and the password.
• A list of network names (SSIDs) will be appeared when
you select the “Network Name” box.
• To show the characters typed in the “Password” box,
select “Show Password”.
• If your network requires specific settings, deselect
“DHCP” to disable DHCP.
– You can use specific IP address, subnet mask,
default gateway, primary DNS, etc.
9 Select “Connect” to apply the settings.
• On the main unit’s display, “Success” appears when
the connection is established. (“ ” will be
displayed.)
– If “Fail” is displayed press [OK], check the network
name (SSID) and the password, and then try the
setting again.
• Depending on the device, the connection complete
screen may not be displayed.
10
Make sure to connect your compatible device
back to your home wireless network.
Note:
• Enable Java and Cookies in your browser settings.
1 Press [RADIO, EXT-IN] on the remote control
repeatedly to select “Network”.
2 To enter “WPS Push” mode
1 Press [SETUP] on the remote control repeatedly
to select “Net Setup” and then press [OK].
“WPS Push” is indicated on the display.
2 Press [OK].
• Alternatively, press and hold [5/9] on the main
unit for at least 4 seconds.
“WPS” flashes on the display.
3 Activate the WPS button on the wireless router.
• On the main unit’s display, “Success” appears when
the connection is established. (“ ” will be
displayed.)
– "Fail" may be displayed if the connection was not
made within the set time limit. Try the setting again. If
"Fail" is still displayed, try other methods.
4 Press [OK] on the remote control to exit the
setting.
∫ Using the WPS PIN code
1 Press [RADIO, EXT-IN] on the remote control
repeatedly to select “Network”.
2 To enter “WPS PIN” mode
1 Press [SETUP] on the remote control repeatedly
to select “Net Setup” and then press [OK].
2 Press [3, 4] on the remote control to select
“WPS PIN” and then press [OK].
• Alternatively, Press and hold [:/6] on the main
unit for at least 4 seconds.
The PIN code is indicated on the display.
3 Enter the PIN code into the wireless router.
Note:
• Once the system enters WPS PIN code mode, you cannot
set up using the WPS button. To use the WPS button, turn
the system off and then on, and redo the network settings.
• Depending on a router, other connected devices may
temporarily lose their connection.
• For details, refer to the operating instructions of the
wireless router.
●●●●●●●●
Method 2:
Using WPS (Wi-Fi Protected Setup™)
A compatible wireless router may have the WPS
identifier mark.
e.g.,
SC-PMX100-100B_EGEBGN-RQT9995-B.book 7 ページ ２０１５年３月３日 火曜日 午前９時８分
7
RQT9995
7 Select your security options for this system.
To set the AirPlay password
1 Select “Yes” and then select “Next”.
2 Set your password and then select “Next”.
• You will need this password the next time this network
setting method is used.
• If you have performed a network reset (> 18)
, the
password will be cleared.
To skip this setting
Select “No” and then select “Next”.
• You can also change this setting after the network
connection is set up. (> 8, “To make network-related
settings”)
8 Select your network name (SSID) and type the
password.
• Check the wireless router for the network name (SSID)
and the password.
• A list of network names (SSIDs) will be appeared when
you select the “Network Name” box.
• To show the characters typed in the “Password” box,
select “Show Password”.
• If your network requires specific settings, deselect
“DHCP” to disable DHCP.
– You can use specific IP address, subnet mask,
default gateway, primary DNS, etc.
9 Select “Connect” to apply the settings.
• On the main unit’s display, “Success” appears when
the connection is established. (“ ” will be
displayed.)
– If “Fail” is displayed press [OK], check the network
name (SSID) and the password, and then try the
setting again.
• Depending on the device, the connection complete
screen may not be displayed.
10
Make sure to connect your compatible device
back to your home wireless network.
Note:
• Enable Java and Cookies in your browser settings.
1 Press [RADIO, EXT-IN] on the remote control
repeatedly to select “Network”.
2 To enter “WPS Push” mode
1 Press [SETUP] on the remote control repeatedly
to select “Net Setup” and then press [OK].
“WPS Push” is indicated on the display.
2 Press [OK].
• Alternatively, press and hold [5/9] on the main
unit for at least 4 seconds.
“WPS” flashes on the display.
3 Activate the WPS button on the wireless router.
• On the main unit’s display, “Success” appears when
the connection is established. (“ ” will be
displayed.)
– "Fail" may be displayed if the connection was not
made within the set time limit. Try the setting again. If
"Fail" is still displayed, try other methods.
4 Press [OK] on the remote control to exit the
setting.
∫ Using the WPS PIN code
1 Press [RADIO, EXT-IN] on the remote control
repeatedly to select “Network”.
2 To enter “WPS PIN” mode
1 Press [SETUP] on the remote control repeatedly
to select “Net Setup” and then press [OK].
2 Press [3, 4] on the remote control to select
“WPS PIN” and then press [OK].
• Alternatively, Press and hold [:/6] on the main
unit for at least 4 seconds.
The PIN code is indicated on the display.
3 Enter the PIN code into the wireless router.
Note:
• Once the system enters WPS PIN code mode, you cannot
set up using the WPS button. To use the WPS button, turn
the system off and then on, and redo the network settings.
• Depending on a router, other connected devices may
temporarily lose their connection.
• For details, refer to the operating instructions of the
wireless router.
●●●●●●●●
Method 2:
Using WPS (Wi-Fi Protected Setup™)
A compatible wireless router may have the WPS
identifier mark.
e.g.,
SC-PMX100-100B_EGEBGN-RQT9995-B.book 7 ページ ２０１５年３月３日 火曜日 午前９時８分
7
RQT9988
10 Provjerite jeste li ponovno spojili kompatibilan
uređaj na kućnu bežičnu mrežu.
Napomena:
• Omogućite Javu i kolačiće u postavkama preglednika.
Metoda 2:
Upotreba WPS-a (Wi-Fi Protected Setup™)
1 Više puta pritisnite [RADIO, EXT-IN] na daljinskom
upravljaču da biste odabrali “Network” (Mreža).
2 Ulazak u način "WPS Push" (WPS pritiskom na
gumb)
1 Pritisnite [SETUP] (Postavljanje) na daljinskom
upravljaču više puta da biste odabrali "Net Setup"
(Postavljanje mreže) i zatim pritisnite [OK].
Na prikazu se prikazuje "WPS Push" (WPS
pritiskom na gumb).
2 Pritisnite [OK] (U redu).
• Druga je mogućnost da pritisnete i barem 4 sekunde
držite [ ] na glavnoj jedinici.
Na zaslonu treperi "WPS".
3 Aktivirajte WPS gumb na bežičnom usmjerivaču.
• Na prikazu glavne jedinice pojavit će se "Success"
(Uspješno) kad se uspostavi veza. (Prikazat će se
“ ”.)
- Ako veza nije uspostavljena unutar zadanog
vremena, može se prikazati "Fail" (Neuspješno).
Ponovno pokušajte postaviti. Ako se i dalje prikazuje
"Fail", isprobajte druge metode.
4 Pritisnite [OK] na daljinskom upravljaču da biste
izišli iz postavljanja.
7 Odaberite svoje sigurnosne mogućnosti za ovaj
sustav. Postavljanje lozinke za funkciju AirPlay
1 Odaberite "Yes" (Da) pa odaberite "Next" (Dalje).
2 Postavite svoju lozinku pa odaberite "Next"
(Dalje).
• Ovu ćete lozinku trebati sljedeći put kad budete
upotrebljavali ovu metodu postavljanja mreže.
• Ako ste izveli ponovno postavljanje mreže ( 18),
lozinka će se izbrisati.
Preskakanje ove postavke
Odaberite "No" (Ne) pa odaberite "Next" (Dalje).
• Također možete promijeniti ovu postavku nakon
postavljanja mrežne veze. ( 8, “Postavljanje postavki
povezanih s mrežom”)
8 Odaberite naziv svoje mreže (SSID) i upišite lozinku.
• Provjerite bežični usmjerivač za naziv mreže (SSID) i
lozinku.
• Popis naziva mreže (SSID) pojavit će kad odaberete
okvir "Network Name" (Naziv mreže).
• Da biste prikazali znakove upisane u okvir "Password"
(Lozinka), odaberite "Show Password" (Prikaži lozinku).
• Ako su za vašu mrežu potrebne posebne postavke,
poništite odabir na "DHCP" kako biste onemogućili
DHCP.
- Možete upotrebljavati određenu IP-adresu, masku
podmreže, zadani ulaz, primarni DNS itd.
9 Odaberite "Connect" (Spoji) kako biste primijenili
postavke.
• Na prikazu glavne jedinice pojavit će se "Success"
(Uspješno) kad se uspostavi veza. (Prikazat će se
“ ”.)
- Ako se prikaže “Fail” (Neuspješno), pritisnite [OK],
provjerite naziv mreže (SSID) i lozinku pa ponovno
pokušajte postavku.
• Ovisno o uređaju zaslon s dovršetkom povezivanja
možda se neće prikazati.
■ Upotreba PIN-a za WPS
1 Više puta pritisnite [RADIO, EXT-IN] na daljinskom
upravljaču da biste odabrali “Network” (Mreža).
2 Ulazak u način "WPS PIN" (PIN za WPS)
1 Pritisnite [SETUP] (Postavljanje) na daljinskom
upravljaču više puta da biste odabrali "Net Setup"
(Postavljanje mreže) i zatim pritisnite [OK].
2 Pritisnite [▲, ▼] na daljinskom upravljaču da biste
odabrali "WPS PIN" i zatim pritisnite [OK].
• Druga je mogućnost da pritisnete i barem 4 sekunde
držite [ ] na glavnoj jedinici.
Na prikazu se prikazuje PIN.
3 Unesite PIN-kod u bežični usmjerivač.
Napomena:
• Nakon što sustav uđe u način PIN-a za WPS, ne možete
postavljati korištenjem WPS gumba. Da biste upotrijebili
WPS gumb, isključite sustav pa ga uključite i ponovite
mrežne postavke.
• Ovisno o usmjerivaču, drugi povezani uređaji mogu
privremeno izgubiti svoju vezu.
• Detalje potražite u uputama za uporabu bežičnog
usmjerivača.
/
/
npr.:
Kompatibilni bežični usmjerivač možda ima
identikacijsku oznaku WPS-a.