Operating Instructions

Making the connections
Connect the AC mains lead only after all the other connections have been made.
1 Connect the DAB/FM antenna.
Be sure to tighten fully the nut.
Rotate the antenna at to improve reception.
2 Connect the speakers.
3 Connect the AC mains lead.
Do not use any other AC mains lead except the
supplied one.
1
2
3
Be careful not to cross
(short-circuit) or reverse the
polarity of the speaker wires
as doing so may damage the
speakers.
Adhesive tape
(not supplied)
(6:)
(6:)
B
A
Red
Black
(6:
)
(6:
)
To household
mains socket
A Pull on the tabs (both sides)
to open.
B Put the AC mains lead onto
one of the concave surfaces.
C Coil the AC mains lead
around the ferrite core and
onto the other concave
surface.
D Close the ferrite core until it
clicks.
Note:
Failure to attach the ferrite core
to the AC mains lead may cause
interference to other devices
nearby.
Attaching the ferrite core near to the terminal
5 cm
Overview of controls
Do the procedures with the remote control. You can also use the buttons on the main unit if they are the
same.
A
Standby/on switch [`], [1]
Press to switch the unit from on to standby mode or vice
versa. In standby mode, the unit is still consuming a
small amount of power.
B Select the audio source
On the main unit:
Press [SELECTOR] repeatedly to select the source:
C Basic playback control
D View the setup menu
E View the content information
F Select and confirm an option
Skip MP3 albums
G Open or close the disc tray
H Decrease the brightness of the display panel
To cancel, press the button again.
I Adjust the volume level
J Mute the sound
To cancel, press the button again.
“MUTE” is also cancelled when you adjust the volume or
when you switch off the system.
K View the play menu
L Select the sound effects
M USB port (DC 5 V 500 mA, FOR AV)
N Disc tray
Put in a disc with the label facing up.
O Select “BLUETOOTH” as the audio source
To start Bluetooth
®
pairing, press and hold
the button.
P Display panel
Q Remote control sensor
Distance: Within approximately 7 m
Angle: Approximately 10° up and 30°down, 30° left and
right
Preparing the remote control
Use alkaline or manganese battery.
Install the battery so that the poles (+ and –) align with those
in the remote control.
Play Press [4/9].
Stop Press [8].
Pause Press [4/9].
Press again to continue playback.
Skip Press [2/3] or [5/6].
Search Press and hold [2/3] or [5/6].
(not supplied)
Basic operations
Bluetooth
®
Preparation
Switch on the Bluetooth
®
feature of the device and put the device near the system.
█ Pairing a device
1 Press and hold [– PAIRING] on the main unit until “PAIRING” is shown.
2 Select “SC-PM272” from the Bluetooth
®
menu of the device.
█ Connecting a device
1 Press [ ].
2 Select “SC-PM272” from the Bluetooth
®
menu of the device.
3 Start playback on the device.
FM Radio
1 Press [RADIO] repeatedly to select “FM”.
2 Press [PLAY MENU] repeatedly to select “TUNEMODE”.
3 Press [ R , T ] to select “MANUAL” and then press [OK].
4 Press [2/3] or [5/6 ] to tune in to the station.
To tune automatically, press and hold the button until the frequency starts changing quickly.
DAB+
1 Press [RADIO] repeatedly to select “DAB+”.
If you select “DAB+” for the first time, the system will tune automatically.
2 Press [PLAY MENU] repeatedly to select “MANUAL SCAN”.
3 Press [R, T] to select the frequency block and then press [OK].
If no station is detected, “SCAN FAILED” is shown.
Adjust the antenna and try again.
PM272EB_TQBM0920_en.fm Page 2 Friday, June 30, 2023 2:01 PM