AKX14P.En.book Page 1 Tuesday, January 31, 2012 2:46 PM Owner’s Manual CD Stereo System Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Model No. SC-AKX14 Please keep this manual for future reference. If you have any questions, contact: 1-800-211-PANA (7262) La guía rápida en español se encuentra en la página 2.
AKX14P.En.book Page 2 Tuesday, January 31, 2012 2:46 PM Do the procedures with the remote control. You can also use the buttons on the main unit if they are the same. Your system and the illustrations can look differently. These operating instructions are applicable to the following system. System SC-AKX14 Main unit SA-AKX14 Speakers SB-AKX14 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit.
AKX14P.En.book Page 3 Tuesday, January 31, 2012 2:46 PM Safety precaution WARNING! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
AKX14P.En.book Page 4 Tuesday, January 31, 2012 2:46 PM FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
AKX14P.En.
AKX14P.En.book Page 5 Tuesday, January 31, 2012 2:46 PM Supplied accessories Placement of speakers Preparing the remote control The right and left speakers are the same. You cannot remove the net of the speakers. Use alkaline or manganese battery. Check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts. (Product numbers correct as of February 2012. This may be subject to change.
AKX14P.En.
AKX14P.En.book Page 7 Tuesday, January 31, 2012 2:46 PM Making the connections 1 Conserving power The system consumes approximately 0.2 W when it is in standby mode. Disconnect the power supply if you do not use the system. Some settings will be lost after you disconnect the system. You have to set them again. 3 Connect the speakers. Connect the FM indoor antenna. Place the antenna where reception is best.
AKX14P.En.book Page 6 Tuesday, January 31, 2012 2:46 PM Overview of controls I Clock and timer operation J Set the program function Q SLEEP A PLAY I J B A F R E K Adjust the volume of the system U L Mute the sound of the system D S E T V F K L RADIO O Select the option P Automatically switch off the system EXT-IN D M Set the play menu item N Set the radio menu item K C Press the button again to cancel.
AKX14P.En.book Page 8 Tuesday, January 31, 2012 2:46 PM Disc Play menu Playing disc 1 2 Press [x, OPEN/CLOSE] on the main unit to open the disc tray. Put in a disc with the label facing up. Press [x, OPEN/CLOSE] again to close the disc tray. Press [CD] and then press [4/9] to start playback. Stop playback Press [8]. Pause playback Press [4/9]. Press again to continue playback. Skip album Press [R, T]. Skip track Press [2] or [6] (main unit: [2/3] or [5/6]).
AKX14P.En.book Page 9 Tuesday, January 31, 2012 2:46 PM USB Radio You can connect and play MP3 tracks from your USB device. Do not use a USB extension cable. The system cannot recognize USB device connected through a cable. Manual tuning 1 2 Connect the USB device to the USB port. Hold the main unit when connecting or disconnecting the USB device. 1 2 Press [USB] and then press [4/9] to start playback. Stop playback Press [8] during playback. “RESUME” is shown.
AKX14P.En.book Page 10 Tuesday, January 31, 2012 2:46 PM Sound effects Clock and timers BASS TREBLE Setting the clock You can set the timer to come on at a certain time to wake you up. This is a 12-hour clock. Preparation Set the clock. 1. Press [SOUND] to select “BASS” or “TREBLE”. 2. Press [Y, U] to adjust the level (-4 to +4). By main unit only 1. Press [MANUAL EQ] to select “BASS” or “TREBLE”. 2. Press [2/3] or [5/6] to adjust the level. SURROUND 1. Press [SOUND] to select “SURROUND”. 2.
AKX14P.En.book Page 11 Tuesday, January 31, 2012 2:46 PM External equipment Troubleshooting You can connect a VCR, DVD player etc. and listen to the audio through this system. Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated do not solve the problem, refer to “Customer Services Directory (United States and Puerto Rico)” on page 1. Preparation • Disconnect the AC power supply cord.
AKX14P.En.book Page 12 Tuesday, January 31, 2012 2:46 PM “ERROR” • An incorrect operation was done. Read the instructions and try again. “NOT MP3/ERROR” • An unsupported MP3 format. The system will skip that track and play the next one. “VBR–” • The system cannot show the remaining play time for variable bit rate (VBR) tracks. “NORMAL” • The “INPUT LEVEL” of AUX source automatically changes from “HIGH” to “NORMAL” when the system detects distorted music sounds. “NODEVICE” • The USB device is not connected.
AKX14P.En.book Page 14 Tuesday, January 31, 2012 2:46 PM Disco ESPAŇOL Cómo realizar las conexiones 1 Cómo reproducir disco 1 Conecte las bocinas. B A (4 ) (4) Menú de reproducción 2 2 2 Pulse [CD] y después pulse [4/9] para iniciar la reproducción. OFF PLAYMODE Reproducir todas las pistas. 1-TRACK Reproduce una pista seleccionada del disco. Pulse los botones numéricos para seleccionar la pista. Detener Pulse [8]. reproducción Conecte la antena de cuadro AM.
AKX14P.En.book Page 15 Tuesday, January 31, 2012 2:46 PM USB Usted puede conectar y reproducir pistas MP3 desde su dispositivo USB. No use un cable de extension USB. El sistema no puede reconocer el dispositivo USB conectado a través de un cable. 1 2 Conecte el dispositivo USB al puerto USB. Sujete la unidad principal al conectar o desconectar el dispositivo USB.
