User Guide

ManualsBrandsPanasonic ManualsStereo SystemSC-PM28

RQT6888

Listening operations

Cassette tapes

1 Press [c OPEN], insert a cassette with the

tape facing in.

When the button is pressed, the unit comes on

automatically. Make sure the cassette is fully inserted

and close the lid by hand.

2 Press [PLAY MODE] on the remote control to

select the reverse mode.

Every time you press the button:

: One side is played.

: Both sides are played.

: Both sides are played repeatedly until

[STOP L, –DEMO] is pressed.

3 Press [TAPE / -] to start playback.

Every time you press the button : 4 R ↔ F 3

F 3 : The forward side (front side) will play.

R : The reverse side will play.

4 Adjust the volume.

To stop tape playback

Press [STOP L, –DEMO].

One-touch play

When the system is OFF and a tape is already inserted, play

starts automatically when you press [TAPE / -].

Cassette tape selection and care

Use normal position tapes.

High position and metal position tapes can be played, but

the unit will not be able to do full justice to the characteristics

of these tapes.

• Tapes exceeding 100 minutes are thin and can break or

get caught in the mechanism.

• Tape slack can get caught up in the mechanism and

should be wound up before the tape is played.

• Endless tapes can get caught up in the deck’s moving

parts if used incorrectly. Use tapes appropriate to this

unit’s auto-reverse mechanism.

To fast-forward or rewind the tape

Press [g

4/REW] or [f

3 /FF] in the stop

mode.

Tape direction To rewind To fast-forward

“ F 3” [g

4/REW] [f

3 /FF]

“

4 R” [f

3 /FF] [g

4/REW]

To find the beginning of a program

(TPS: Tape Program Sensor)

TPS finds the beginning of a track and resumes play from

there. Each press increases the number of tracks skipped,

up to a maximum of 9.

Press [g

4/REW] or [f

3 /FF] during play.

Notes

The TPS function searches for silent parts of about 4

seconds in length which are normally found between tunes.

As a result, it may not function properly in the following

cases:

• With short silent parts

• When noise occurs between tunes

• With silent parts found within tunes

Listening operations

DEMOSTOP

OPEN

REW

FF,

TAPE

DOWN

VOLUME

REW

CLEAR

ALBUM

12 3

78 9

TAPE

APE

TUNER

BAND

VOL VOL

AUX

ABC

DEF

GHI

JKL

MNO

TUV

WXYZ

PQRS

ENTER

DISC

MARKER

INTRO

REPEA

DIMMER

DISPLA

RE-MASTER

TING

ING

SOUND

S.SOUND EQ

PLAY

REC

SLEEP

AUTO OFF

SHIFT

TITLE

OCK

TIMER

PROGRAM

DEL

ACE

PLA

Y MODE

PLAY MODE

OPEN

Forward side

Insert inside the

guides

RQT6888(22-27)new5.P65 2/17/03, 7:59 PM23

Summary of content (10 pages)

PAGE 1
Cassette tapes 1 Press [c OPEN], insert a cassette with the tape facing in. When the button is pressed, the unit comes on automatically. Make sure the cassette is fully inserted and close the lid by hand. OPEN 2 1 Press [PLAY MODE] on the remote control to select the reverse mode. STOP AUTO OFF SLEEP CL CK CLOCK TIMER DISPLAY DISPLA ABC DISC 2 : One side is played. : Both sides are played. : Both sides are played repeatedly until [STOP L, –DEMO] is pressed.
PAGE 2
Before recording To protect tapes against further recording. A Listening operations Side A Types of tapes which can be recorded correctly Tab for side B Use normal position tapes. High position and metal position tapes can be used, but the unit will not be able to record or erase them correctly. Tab for side A To re-record Normal position tape A Erasure prevention The illustration shows how to remove the tabs to prevent recording. To record on the tape again, cover as shown.
PAGE 3
A Recording from the radio A Preparation: Do the preparatory steps (A page 24). 1 Tune to the required station. (\ page 10 or 11) 2 , DEMO STOP 2 Press [[/ J REC] to start recording. To stop recording Press [STOP L, –DEMO]. To cut an unnecessary part while recording 1. Press [a/J REC] during the unnecessary part. The cassette deck will go into the stop mode. 2. Press [a/J REC] to resume recording again. Recording will continue in the same direction as before.
PAGE 4
RE-MASTER A Using the sound quality settings S.SOUND EQ By remote control onlyly You can choose one of four types of sound quality with Preset EQ or enhances the bass and treble effect of the sound with Manual EQ.
PAGE 5
A Auto-off function A AUTO OFF SLEEP AUTO OFF CL CK CLOCK TIMER DISPLAY DISPLA PLAY REC DIMMER ABC DEF 2 3 DISC 1 JKL By remote control only When CD or tape is selected as the source To save power, the unit turns off if it is left unused for 10 minutes. MNO PROGRAM GHI 4 5 6 PLAYY MODE PLA PQRS TUV WXYZ 7 8 9 SPACE REPEAT REPEA 0 DEL 10 Note This function does not work if the source is tuner or AUX.
PAGE 6
Using the timers 5 AUTO OFF SLEEP CL CK CLOCK TIMER DISPLAY DISPLA PLAY REC DIMMER ABC DEF 2 3 DISC 1 JKL 4 1 22 3 2 MNO PROGRAM GHI 4 5 6 PLAYY MODE PLA PQRS TUV WXYZ 7 8 9 DEL 0 SPACE REPEAT REPEA 10 CD CLEAR TUNER BAND TAPE AUX VOL VOL ALBUM REW FF TITLE MARKER SEARCH ENTER RE-MASTER SHIFT S.SOUND EQ SOUND MUTING MU ING INTRO 1 22 3 2 4 1 SHIFT CLOCK/ TIMER DISPLAY 21 31 Using the play/record timer By remote control only The timer has two functions.
PAGE 7
Using the timers A A AUTO OFF SLEEP CL CK CLOCK TIMER DISPLAY DISPLA PLAY REC DIMMER ABC DEF 2 3 DISC 1 JKL MNO PROGRAM GHI 4 5 6 PLAY MODE PQRS TUV WXYZ 7 8 9 DEL 0 SPACE SP ACE REPEAT 10 CD CLEAR TUNER BAND TAPE APE AUX VOL VOL ALBUM REW FF TITLE MARKER SEARCH ENTER RE-MASTER SHIFT S.
PAGE 8
Troubleshooting guide Before requesting service, make the below checks. If you can’t fix the system as described below, or if something not listed here occurs, refer to the enclosed to locate an Authorized Service Center convenient to you or contact your dealer. Reference pages are shown as black circled numbers 6. Common Problems No sound. Turn the volume up. The speaker cords may be shorted. Turn the unit off, check and correct the connections and turn the unit on.
PAGE 9
Specifications AMPLIFIER SECTION CASSETTE DECK SECTION SPEAKER SECTION RMS Power output 10% Total harmonic distortion 1 kHz, both channels driven (Low channel) 35 W per channel (6 Ω) 8 kHz, both channels driven (High channel) 35 W per channel (6 Ω) Total Bi-Amp power 70 W per channel Input sensitivity AUX 250 mV Input Impedance AUX 11.
PAGE 10
SUOMI CAUTION! VAROITUS! THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.