SC-HTB370PPC_RQT9777-1P_mst.book Page 1 Tuesday, January 29, 2013 11:48 AM Owner’s Manual Home Theater Audio System Model No. SC-HTB370 Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use. If you have any questions, contact: U.S.A. and Puerto Rico: 1-800-211-PANA (7262) Canada: 1-800-561-5505 Register online at www.panasonic.com/register (U.S.
SC-HTB370PPC_RQT9777-1P_mst.book Page 2 Tuesday, January 29, 2013 11:48 AM IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water.
Page 3 Tuesday, January 29, 2013 CAUTION THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note: Unit ≥ Do not place sources of naked flames, such as lighted candles, on this unit. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SC-HTB370PPC_RQT9777-1P_mst.book Page 4 Tuesday, January 29, 2013 11:48 AM Table of contents IMPORTANT SAFETY INSTRUCTIONS ............................................................ 2 Before use Supplied items ................................................................................................... 5 This system (SC-HTB370).......................................................................................................... 5 Accessories .................................................
SC-HTB370PPC_RQT9777-1P_mst.book Page 5 Tuesday, January 29, 2013 11:48 AM Before use ≥ The illustrations shown may differ from your unit. ≥ Operations in this Owner’s Manual are described mainly with the remote control, but you can perform the operations on the main unit if the controls are the same. Supplied items ∏ 2 Front speakers (SB-HTB570) Before use ∏ 1 Active subwoofer (SB-HWA370) Accessories Check the supplied accessories before using this system.
SC-HTB370PPC_RQT9777-1P_mst.book Page 6 Tuesday, January 29, 2013 11:48 AM Control reference guide This system (Front) 4 5 6 7 1 2 3 Main unit 1 Standby/on switch (Í/I) Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.
SC-HTB370PPC_RQT9777-1P_mst.book Page 7 Tuesday, January 29, 2013 11:48 AM Before use This system (Rear) 1 2 3 4 AC IN terminal (> 23) Speaker terminals (> 23) TV terminal (> 22) BD/DVD terminal (> 22) 5 6 7 USB port (for service use only) AUX terminal (> 22) Active subwoofer on/off button (> 24) § The I/D SET button is only used when the main unit is not paired with the active subwoofer.
SC-HTB370PPC_RQT9777-1P_mst.book Page 8 Tuesday, January 29, 2013 11:48 AM Remote control ∫ Before using for the first time Remove the insulation sheet A.
SC-HTB370PPC_RQT9777-1P_mst.book Page 9 Tuesday, January 29, 2013 11:48 AM Step 1 Selecting the placement method Getting started ≥Choose a placement method that suits you best.
SC-HTB370PPC_RQT9777-1P_mst.book Page 10 Tuesday, January 29, 2013 11:48 AM Caution ≥ This system is to be used only as indicated in these instructions. Failure to do so may lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance. ≥ Do not attempt to attach the speakers to a wall using methods other than those described in this manual.
SC-HTB370PPC_RQT9777-1P_mst.book Page 11 Tuesday, January 29, 2013 11:48 AM Step 2 Assembling the speakers When attaching the speakers to a wall Place the speakers horizontally The speakers can be wall mounted by drilling screws into the wall, etc. Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs). The screws and other items are not supplied as the type and size will vary with each installation.
SC-HTB370PPC_RQT9777-1P_mst.book Page 12 Tuesday, January 29, 2013 11:48 AM Connect the speaker cables. 1 Insert the wire fully. r: White s: Blue line 45 ≥ Insert the wire fully, taking care not to insert beyond the wire insulation. 2 Press into the groove.
SC-HTB370PPC_RQT9777-1P_mst.book Page 13 Tuesday, January 29, 2013 11:48 AM Fit the speaker securely onto the screw(s). Red connector: The speaker attached to the red connector cable is to be placed on the right side. White Getting started White connector: The speaker attached to the white connector cable is to be placed on the left side. Red A Right speaker connector B Left speaker connector DO ≥ Move the speaker so that the screw is in this position.
SC-HTB370PPC_RQT9777-1P_mst.book Page 14 Tuesday, January 29, 2013 11:48 AM Place the speakers vertically The speakers can be wall mounted by drilling screws into the wall, etc. Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs). The screws and other items are not supplied as the type and size will vary with each installation. ≥For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.” (> 15).
SC-HTB370PPC_RQT9777-1P_mst.book Page 15 Tuesday, January 29, 2013 11:48 AM Drive a screw into the wall. ≥ Use the measurements indicated below to identify the screwing positions on the wall. ≥ Leave at least 20 mm (25/32q) of space above and on each side of the speaker to allow enough space for fitting the speaker. ≥ Keep the screws out of reach of children to prevent swallowing.
SC-HTB370PPC_RQT9777-1P_mst.book Page 16 Tuesday, January 29, 2013 11:48 AM When placing the speakers on a table Place the speakers using the leg stands ∏ 2 Speakers ∏ 2 Speaker cables WHITE: Left RED: Right ∏ 2 Leg stands ∏ 4 Screws ∏ 1 Metal bracket ≥For a safety measure to prevent the speakers from falling, refer to page 20. ≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
SC-HTB370PPC_RQT9777-1P_mst.book Page 17 Tuesday, January 29, 2013 11:48 AM Place the speakers using the support legs and speaker feet ∏ 2 Speakers ∏ 2 Speaker cables WHITE: Left RED: Right ∏ 1 Metal bracket ∏ 2 Support legs ∏ 4 Screws ∏ 2 Speaker feet ≥For a safety measure to prevent the speakers from falling, refer to page 20. ≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
SC-HTB370PPC_RQT9777-1P_mst.book Page 18 Tuesday, January 29, 2013 11:48 AM Place the speakers using the speaker bases ∏ 2 Speakers ∏ 2 Speaker cables WHITE: Left RED: Right ∏ 2 Speaker bases ∏ 4 Screws ∏ 2 Stand necks ≥For a safety measure to prevent the speakers from falling, refer to page 20. ≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it. Assemble the speakers following step 1 of “Place the speakers vertically” (> 14).
SC-HTB370PPC_RQT9777-1P_mst.book Page 19 Tuesday, January 29, 2013 11:48 AM Attach the speaker base. ≥ The two speakers are interchangeable. ≥ Keep the screws out of reach of children to prevent swallowing. Screw (supplied) ≥ Tighten securely. Press into the groove. Red connector: The speaker attached to the red connector cable is to be placed on the right side. White connector: The speaker attached to the white connector cable is to be placed on the left side.
SC-HTB370PPC_RQT9777-1P_mst.book Page 20 Tuesday, January 29, 2013 11:48 AM Additional speaker fall prevention measures To prevent the speakers from falling, it is recommended, as an additional protection measure, to attach the speakers to the wall or table with a fall prevention cord (hereafter “cord”).
SC-HTB370PPC_RQT9777-1P_mst.book Page 21 Tuesday, January 29, 2013 11:48 AM When placing the speakers on a table Horizontal placement Vertical placement Getting started A Cord§ B Screw eye C Wall D Approx. 150 mm (5 29/32q) ≥ Depending on the placement of the speakers, the screwing position of the screw eye may differ.
SC-HTB370PPC_RQT9777-1P_mst.book Page 22 Tuesday, January 29, 2013 11:48 AM Step 3 Connections ≥Turn off all equipment before connection and read the appropriate operating instructions. Do not connect the AC power supply cord until all other connections are completed.
SC-HTB370PPC_RQT9777-1P_mst.book Page 23 Tuesday, January 29, 2013 11:48 AM Speaker cable connection Match the connector shape and connect to the terminals of the same color. 6 R 6 L SPEAKERS/HAUT-PARLEURS 6 R 6 L DIGITAL AUDIO IN SPEAKERS/HAUT-PARLEURS AUX AC IN A RED Right speaker connector B WHITE Left speaker connector AC power supply cord connection Getting started ≥ Connect only after all other connections are completed.
SC-HTB370PPC_RQT9777-1P_mst.book Page 24 Tuesday, January 29, 2013 Active subwoofer wireless connection Preparation ≥ Turn on the main unit. Press [BÍ CI]. 11:48 AM Bluetooth® connection By using the Bluetooth® connection, you can listen to the sound from the Bluetooth® audio device from this system wirelessly. Preparation ≥ Turn on the Bluetooth® feature of the device and place the device near the main unit. Bluetooth® pairing Press [ ] to select “ ”.
SC-HTB370PPC_RQT9777-1P_mst.book Page 25 Tuesday, January 29, 2013 Using this system 11:48 AM Operations Adjust the volume and sound effect level. Preparation ≥ Turn on the active subwoofer. ≥ Turn on the TV and/or connected device. ∫ To adjust the volume of this system Press [i VOL j]. ≥ Volume range: 0 to 100§ ∫ To adjust the dialog effect level This setting will change the level of the Clearmode dialog effect. (> 26) 1 Press [i DIALOG LEVEL j] to display the current level.
SC-HTB370PPC_RQT9777-1P_mst.book Page 26 Tuesday, January 29, 2013 11:48 AM 3D sound This system provides a feeling that the sound and the image are as one. ≥ To change the applied effect, refer to “Sound modes”. (> right) e.g., Image of 3D sound field Sound modes By changing the sound mode, it is possible to enjoy the sound that is suitable to the TV program or image from the connected device. ∫ To select the sound mode Press [SOUND].
SC-HTB370PPC_RQT9777-1P_mst.book Page 27 Tuesday, January 29, 2013 11:48 AM Advanced operations Audio format indicator Press and hold [SOUND] for more than 4 sec. With this function, you can prevent sudden loud sounds. The output will be reduced automatically when the input exceeds a certain level. Press and hold [INPUT SELECTOR] on the remote control for more than 4 sec. ≥ The current audio format is indicated for 5 sec. “STADIUM” indicator blinks: Dolby Digital is the audio format.
SC-HTB370PPC_RQT9777-1P_mst.book Page 28 Tuesday, January 29, 2013 Using the Dolby Virtual Speaker effect Depending on your preference, It is possible to turn off the 3D surround effect and the clear-mode dialog effect. While pressing and holding [SOUND] on the remote control, press and hold [VOL i] on the main unit for more than 4 sec. “STANDARD” indicator blinks: 3D surround effect and clear-mode dialog effect is on. “STEREO” indicator blinks: 3D surround effect and clear-mode dialog effect is off.
SC-HTB370PPC_RQT9777-1P_mst.book Page 29 Tuesday, January 29, 2013 Troubleshooting 11:48 AM Reference While the main unit is on, press [Í/I] on the main unit for more than 4 sec. (All the indicators will blink twice when this system is reset.) Pairing cannot be done. Check the Bluetooth® device condition. The device cannot be connected. ≥ The pairing of the device was unsuccessful or the registration has been replaced. Try pairing the device again.
SC-HTB370PPC_RQT9777-1P_mst.book Page 30 Tuesday, January 29, 2013 There is no audio. The power of the main unit turns off automatically. (When the main unit detects a problem, a safety measure is activated and the main unit automatically switches to standby mode.) ≥ There is a problem with the amplifier. ≥ Is the volume extremely high? If so, lower the volume.
Page 31 Tuesday, January 29, 2013 SPEAKER SECTION SPEAKER GENERAL Front speakers 3 way, 3 speaker system (Bass reflex type) Speaker unit(s) Impedance 6 ≠ Woofer 5.7 cm (2 1/4q) cone type Tweeter 2.
SC-HTB370PPC_RQT9777-1P_mst.book Page 32 Tuesday, January 29, 2013 Unit care ∫ Clean this system with a soft, dry cloth ≥ When dirt is heavy, wring a cloth moistened in water tightly to wipe the dirt, and then wipe it with a dry cloth. ≥ When cleaning the speakers, use a fine cloth. Do not use tissues or other materials (towels, etc.) that can fall apart. Small grains may get stuck inside the speaker cover. ≥ Never use alcohol, paint thinner or benzine to clean this system.
SC-HTB370PPC_RQT9777-1P_mst.book Page 33 Tuesday, January 29, 2013 11:48 AM Indicator illumination The indicators display the condition of this system by flashing. The indicator patterns illustrated below are displayed during normal operational conditions. They do not refer to the indications of a problem. Indicator Description The BD/DVD indicator blinks§2 and sound mode indicators light up in sequence for 1 minute.
SC-HTB370PPC_RQT9777-1P_mst.book Page 34 Tuesday, January 29, 2013 11:48 AM Limited Warranty (ONLY FOR U.S.A.
SC-HTB370PPC_RQT9777-1P_mst.book Page 35 Tuesday, January 29, 2013 11:48 AM Limited Warranty (ONLY FOR CANADA) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT - LIMITED WARRANTY Panasonic Canada Inc.
SC-HTB370PPC_RQT9777-1P_mst.book Page 36 Tuesday, January 29, 2013 11:48 AM -If you see this symbolInformation on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. ® As an ENERGY STAR Partner, Panasonic has determined that ® this product meets the ENERGY STAR guidelines for energy efficiency.
