User Guide

16
RQT7621
INTRO
STEP 5 Channel reception settings
Preparation
≥Confirm that the aerial is connected correctly.
≥Switch [HOME THEATER, TV] to “HOME THEATER”.
≥When connecting to a television with the VIDEO OUT,
S-VIDEO OUT or COMPONENT VIDEO OUT terminal
(➡page 13).
≥When connecting to a television that does not have
the Q Link function (➡page 55).
This unit’s Auto-Setup function automatically tunes all available TV
stations and synchronizes the time and date with that of the
receiving station after tuning is completed.
≥When connecting to a television with RF socket only
(➡page 12)
1 Turn on the television and select the
appropriate AV input to suit the
connections to this unit.
2 Press [Í] to turn the unit on.
Auto-Setup starts. This takes about 5 minutes.
(When connecting to a television with RF socket only)
Set the new RF output channel to TV (refer to the
instructions for your TV).
Select an unused channel pre-set on your TV and tune it to
the RF output channel number shown on the unit’s display.
(When the Auto-Setup screen does not appear clearly even
after performing the above operations, re-tune the channel
until the Auto-Setup screen becomes clear.)
3 When Auto-Setup has been completed, the Owner ID
settings screen appears.
Press [1] and press the numbered
buttons to enter a 4-digit PIN number.
≥Make a note of the PIN number (don’t forget), as it is not
possible to return to the factory preset.
4 Press [ENTER] twice to store the PIN
number.
The cursor moves to “Name”.
5 Press [1].
6 Press [3, 4] to select a letter and
then press [1].
Repeat this to enter the name.
7 Press [ENTER] to store the name.
8 Press [4] and [1], and then repeat
steps 6, 7 to enter and store “House
No.” and “Postcode”.
9 Press [RETURN].
The Owner ID settings screen disappears.
To stop partway
Press [RETURN].
∫ If the clock setting menu appears
Set the clock manually (➡ page 52).
∫ To confirm that stations have been tuned
correctly (➡page 51)
∫ To restart Auto-Setup (➡ page 51)
You can also use the following method to restart Auto-Setup.
When the unit is on and stopped
Press and hold [X CH] and [CH W] on the main unit for about 5
seconds.
≥All the settings except for the ratings level, ratings password,
Owner ID and time settings return to the factory preset. The timer
recording programmes are also cancelled.
[When connecting to a television with RF socket only (➡page 12)]
∫ To enter the satellite station’s name (➡page 51)
The name of the satellite station is not set automatically. (“-- ---” will
appear under “Name” in the program list). After Auto-Setup is
completed, enter the name manually.
∫ If you connect other equipment to AV2 terminal
of this unit
Change the “AV2 Input” and “AV2 Connection” in the SETUP menu
to match the connected equipment (➡page 50).
Auto-Setup
(Setup without Q Link functions)
CHX, CHW
CH
VOLUME
SKIP
STOP PAUSE PLAY/
SLOW/SEARCH
CANCEL
123
4
5
6
789
0
HOME THEATER TV
EXT LINK
MULTI REAR
DUBBING
S.POSITION
CREATE CHAP
C.FOCUS
REC MODE
CH SELECT
RETURN
ERASE TIMER TIME SLIP
AV2/OPT
TOP MENU
ENTER
DIRECT NAVIGATOR
FUNCTIONS
MIX
2CH
REC
TEST
MANUAL SKIP
REPEAT
MUTING
AV
AUXFM/AMDVDHDD
DISPLAY
PRO LOGIC
VIDEO Plus +
SHIFT
SHIFT
DIRECT TV REC
FM MODE
SUB MENU
STATUS
EQ/SFC
PROG/CHECK
PROG/CHECK
HDD/DVD INPUT
AUDIO
S W. LEVEL
-/--
F
A B C D
AUXHDD DVD FM/AM
OPEN/CLOS E
UPDOWN
VOLUME
INPUT SELECTOR
REC
TIME SLIP
TUNE
CH CH
PULL-OPEN
RDS
Í
3 4 2 1
ENTER
RETURN
Í/I
W X CH
FUNCTIONS
VIDEO Plusr
HOME
THEATER,
TV
¢ CANCEL
Numbered
buttons
Auto-Setup
Ch 1
Auto-Setup in progress, please wait.
RETURN: to abort
RETURN
RETURN
Owner ID
RETURN : leave
PIN number
¢¢¢¢
Name
House No.
Postcode
HT1500_EB.book 16 ページ ２００４年５月２８日 金曜日 午後１時４１分