ORDER NO. MD0412597C3 CD Stereo System SA-AK230GCP Colour (S)... Silver Type Specifications n AMPLIFIER SECTION Track system RMS output power Heads THD 10%, both channels driven Record/playback 100 W per channel (5 Ω) 1 kHz Total RMS power 200 W Erasing system Tape speed 2.5 µV (IHF) 35 Hz - 14 kHz S/N 50 dB (A weighted) Wow and flutter 0.18 % (WRMS) Fast forward and rewind time Approx.
SA-AK23 0GCP D/A converter MASH (1 bit DAC) Mass Pickup Operating temperature range Wavelength 780 nm Beam Source Operating humidity range Semiconductor laser SC-AK230 (GCP) Number of channels Music center: SA-AK230 (GCP) 2 (Stereo) (FL,FR) Speaker: SB-AK230 (GC) n GENERAL Notes: Power Supply 1. Specifications are subject to change without notice. Mass and dimensions are approximate.
SA-AK23 0GCP 18 Printed Circuit Board 73 18.1. (A) CD Servo P.C.B. 73 18.2. (B) Main P.C.B. 74 18.3. (C) Panel P.C.B. 76 18.4. (D) Transformer P.C.B. 78 21.1. IC7002 (MN6627953HB) Servo processor/ Digital signal processor/ Digital filter/ D/A converter Traverse motor/ Spindle motor drive 21.3. IC2801 (C2CBJG000565) System Microprocessor 18.5. (E) CD Detect P.C.B., (F) Spindle Position P.C.B., (G) CD Loading P.C.B. & (K) Tuner Pack P.C.B. 85 21.2.
SA-AK23 0GCP 1 Before Use Be sure to disconnect the mains cord before adjusting the voltage selector. Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will be used. (If the power supply in your area is 117V or 120V, set to the “127V” position.) Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries, the correct voltage is already set.
SA-AK23 0GCP 8. Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device). 5 Handling the Lead-free Solder 5.1. About lead free solder (PbF) Distinction of PbF P.C.B.: P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B.
SA-AK23 0GCP 6 Handling Precautions For Traverse Deck The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup). · Handling of traverse deck (optical pickup) 1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock. 2.
SA-AK23 0GCP 7 Precaution of Laser Diode Caution : This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens. Wavelength : 780 nm Maximum output radiation power from pick up : 100 µW/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous. 2. Do not adjust the variable resistor on the pick up unit.
SA-AK23 0GCP 8 Accessories Remote Control FM Antenna AC Cord AM Loop Antenna AC Plug Adaptor 8
SA-AK23 0GCP 9 Operation Procedures 9
SA-AK23 0GCP 10
SA-AK23 0GCP 10 Disassembly and Assembly of Main Component “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassemblin g and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. 2. For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required. 3.
SA-AK23 0GCP 10.2. Gear for servicing (jig) Information 1. This unit has a gear which is used for checking items (Open/Close of disc tray, up/down operation of traverse unit by manually) when servicing. 2. For preparation of gear (for servicing), perform the procedures as follows. 3. In case of re-servicing the same set, the “gear for servicing” may has been taken off because it has been used. The “gear for servicing” must be stored. · Remove the gear provided with mecha cover as shown below.
SA-AK23 0GCP 10.3. Disassembly of Top Cabinet Step 1 Remove 2 screws at each side and 5 screws at rear panel. Step 2 Lift up both sides of the top cabinet, push the top cabinet towards the rear and remove the top cabinet. 10.4. Disassembly of CD Lid (The CD changer unit can be removed after the CD Lid is removed) · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet · Opening the disc tray automatically (Using Power Supply) Step 1 Connect the AC power cord.
SA-AK23 0GCP Step 2 Release the 2 claws, and then remove the CD lid cover. Step 6 Press the POWER button to turn the power off. · [Opening the disc tray manually (Using service tools)] Step 3 Repeat Step 2 but rotate the gear tools in anti-clockwise direction. Step 1 Insert the gear tool into the hole on the underside of CD chassis and then rotate in the direction of arrow. The disc tray will be opened. Step 4 The disc tray will be closed.
SA-AK23 0GCP 10.5. Disassembly of Rear Panel · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet Step 1 Remove 8 screws and disconnect wire CN2810 (Fan) at rear cabinet as shown. 10.6. Disassembly of CD Mechanism Unit · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet Step 1 Remove one screw at rear panel. Step 2 Detach the FFC wires (CN2801 & CN2805). Step 4 Remove 4 screws. Step 5 Remove the CD chassis. Step 6 Lay the CD mechanism unit as shown.
SA-AK23 0GCP 10.7. Disassembly of Main P.C.B. · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 10.4 - Disassembly of CD Lid · Follow the (Step 1) of Item 10.5 - Disassembly of Rear Panel · Follow the (Step 1) - (Step 3) of Item 10.6 - Disassembly of CD Mechanism Unit Step 1 Disconnect FFC wires CN2803 & CN2806 from Main P.C.B. Step 2 Lift up Main P.C.B. by disconnecting connectors CN5800 & CN5801 as arrow shown above. 10.8.
SA-AK23 0GCP · Replacement of the Power Amplifier IC/ Voltage Regulator Step 1 Remove 2 screws fixed to the Power Amplifier IC and 1 screw to Voltage Regulator. Step 3 Unsolder the terminals of Power Amp IC, transistor and replace the components. Step 4 Fix back the cut portion with a screw as shown. Step 2 Break the joint with a metal cutter as shown below. 10.9. Disassembly of Transformer P.C.B. · Follow the (Step 1) - (Step 2) of Item 10.
SA-AK23 0GCP 10.10. Disassembly of Front Panel Unit · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 10.4 - Disassembly of CD Lid · Follow the (Step 1) - (Step 3) of Item 10.6 - Disassembly of CD Mechanism Unit Step 1 Lay the unit as shown below. Step 2 Release 2 claws at bottom and 2 claws each side, draw the front panel ass’y forward. Step 4 Remove 10 screws. Step 5 Disconnect CN5950). Step 3 Remove volume knob.
SA-AK23 0GCP Step 7 Unsolder the motor terminals. Step 8 Remove Deck Mechanism P.C.B. 10.12. CD Mechanism Main Component Replacement Procedures · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 10.4 - Disassembly of CD Lid · Follow the (Step 1) - (Step 6) of Item 10.6 - Disassembly of CD Mechanism Unit 10.12.1. Replacement of the Traverse Deck Step 1 Remove the CD changer unit. Step 2 Insert the gear with hexagonal wrench into the hole.
SA-AK23 0GCP Step 6 Lift up the traverse deck ass’y. Step 10 Remove the FFC board from the connector, and then remove the CD Servo P.C.B. Step 7 Remove the traverse deck ass’y from the timing lever. Caution: When removing or inserting the traverse deck avoid touching the OPU lens and pressing onto the turntable. Step 11 Remove the pin. Step 8 Remove 3 screws. Step 9 Unsolder the motor terminals (4 points). Step 12 Release the claw, and then remove the traverse deck ass’y.
SA-AK23 0GCP Note: Step 1 Install the traverse deck ass’y to the timing lever. Be careful not to lose the 3 floating spring because those will also be removed on removal of the traverse deck ass’y. Step 2 Align the boss of traverse deck ass’y with the slot of traverse cam gear. · Installation of the CD Servo P.C.B. after replacement Step 1 Connect the FFC board. Step 2 Install the CD servo P.C.B. in the traverse deck ass’y. Step 3 Remove 3 screws. Step 4 Solder. Step 3 Force the claw of timing lever.
SA-AK23 0GCP Step 5 With pressing the claw (B) in the direction of arrow (1), force the connection lever in the direction of arrow (2). 10.12.2. Replacement for the Disc Tray Step 1 Remove 4 screws. Step 2 Remove the upper plate. Step 3 Remove 3 screws. Step 4 With lifting the claw in the direction of (1), draw the CD Detect P.C.B. in the direction of arrow (2). Step 5 Remove the mechanism cover.
SA-AK23 0GCP Step 6 Insert the gear with hexagonal wrench into the hole. Step 9 With forcing the left guide bar manually because the left guide bar interfers with claw, draw the disc tray. [Installation of the disc tray after replacement] Step 7 Rotate the hexagonal wrench in the direction of arrow, and then open the disc tray fully. Step 1 Slide the drive rack fully in the direction of arrow. Step 8 Release the both claws, and then draw the disc tray.
SA-AK23 0GCP NOTE: Force the right guide bar of tray base manually not to move upwards. Step 4 Holding the disc tray manually, push the disc tray in the direction of the arrow. 10.12.3. Disassembly and reassembly for mechanism base drive unit Step 1 Remove 3 screws. Step 5 Release the 2 claws, and then remove the bottom SW P.C.B.. Step 2 Release the claw, and then remove the gear holder. Step 3 Remove the belt and change gear spring. NOTE: Take care not to lose the change gear spring.
SA-AK23 0GCP Step 9 Pressing the claw (B) in the direction of arrow (1), force the connection lever in the direction of arrow (2). Step 6 Install the tray lock spring to hook temporary. Step 7 Release the claw, and then remove the tray lock. Step 8 Release the claw, and then remove the rear lock. Step 10 Move the slide plate 1 to the end of stock side.
SA-AK23 0GCP Step 13 Remove the traverse relay gear, traverse cam gear and drive gear. Step 11 Lift up the left end of spindle base unit in the direction of arrow (1), and then remove the unit in the direction of arrow (2). [Dissassembly/reassembly for the spindle base unit] Step 1 Draw the 5 disc spacers. Step 2 Pushing the claw, slide the support plate in the direction of arrow, and then remove it. Step 12 Remove slide plate 1 and slide plate 2.
SA-AK23 0GCP Step 3 Rotate the disc lever in the direction of arrow (1), draw the disc lever. NOTE: Hold the loading stopper ass’y manually bacause it is flipped by spring. NOTE: Take care not to lose the disc lever spring. Step 6 Remove the cushion spring. Step 7 Remove the loading stopper ass’y in the direction of arrow. Step 4 Release the 2 claws, and then draw the relay gear B. Step 5 Release the 2 claws as shown below.
SA-AK23 0GCP Step 8 Release the 2 claws, and then remove the relay gear A. Step 9 Release the 2 claws, and then remove the spindle shaft. Step 12 Squeeze the shaft of lower hook, and then draw it. Step 13 Rotate the lower spindle in the direction of arrow until the lower spindle interferes with stopper. Step 10 Remove the lower spindle spring with tweezers. Step 11 Force the lower hook with thin tip of minus screwdriver.
SA-AK23 0GCP Step 1 Install the traverse cam gear. spread the hold bars of loading stopper and remove the UP/DOWN base. Step 2 Rotate the traverse cam gear to the direction of arrow. [Installation for loading stopper ass’y] Step 1 Align the claw of loading stoppers ass’y with the slot of spindle base. (Caution should be exercised when alignment of claw due to the size of claws.) Step 2 Lower the loading stopper ass’y, and then align the lower spindle with the trapezoid tooth of relay gear A.
SA-AK23 0GCP Step 4 Install the slide plate 2 to the mechanism base, and then match to the connection lever. Step 7 Move the slide plate 1 to forward fully. Step 5 Install the slide plate 1 to the mechanism base, and then match to the connection leve and align the trapezoid tooth of traverse relay gear with the slide plate 1. Step 8 Install the rear lock. (The claw should be latched.) Step 9 Install the Spindle Position P.C.B.. (The claw should be latched.) Step 10 Install the tray lock.
SA-AK23 0GCP Step 13 Install the gear holder, and then tighten the screw (a). Step 11 Remove the tray lock spring from hook,and then latch to the tray lock. Step 12 Install the UP/DOWN gear, change gear, change gear spring, pulley gear and belt in the order of (1) - (5). Step 14 Install the tray base, traverse ass’y, mechanism cover and upper plate. [Operation check after servicing] Check the proper operation of following items with gear and hexagonal screwdriver. 1. Open/close of tray base. 2.
SA-AK23 0GCP 10.12.4. Replacement for the motor ass’y P.C.B. Step 7 Release the claw (B), and then remove the motor ass’y. [Notice for motor ass’y installation] 1. Locate the name plate of motor to the traverse ass’y. 2. Align the hole of motor with the ribs. Step 1 Install the belt temporarily. NOTE: Take care not apply the grease to the belt. Step 2 Upset the CD loading unit. Step 3 Remove 3 screws. Step 4 Unsolder the plunger terminals (2 points). Step 5 Unsolder the motor terminals (2 points).
SA-AK23 0GCP 10.13. Replacement for the pinch roller ass’y and head block · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 10.4 - Disassembly of CD Lid · Follow the (Step 1) - (Step 3) of Item 10.6 - Disassembly of CD Mechanism Unit · Follow the (Step 1) - (Step 3) of Item 10.10 - Disassembly of Front Panel Unit · Follow the (Step 1) - (Step 5) of Item 10.11 - Disassembly of Deck Mechanism Unit * The mechanism as shown below is for DECK1.
SA-AK23 0GCP 10.14. Replacement for the Deck motor ass’y, capstan belt A, capstan belt B and winding belt · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet · Follow the (Step 1) - (Step 6) of Item 10.4 - Disassembly of CD Lid · Follow the (Step 1) - (Step 3) of Item 10.6 - Disassembly of CD Mechanism Unit · Follow the (Step 1) - (Step 3) of Item 10.10 - Disassembly of Front Panel Unit · Follow the (Step 1) - (Step 5) of Item 10.
SA-AK23 0GCP Step 7 Put the capstan belt A temporarily as shown below. Step 2 Put the winding belt on the pulley temporarily. Step 3 Install the flywheel F. Step 4 Put the winding belt on the flywheel F. Step 5 Install the winding lever and spring while pressing the winding arm in the direction of arrow. Step 6 Install the flywheel R. Step 8 Put the capstan belt B on the motor ass’y pulley. Step 9 Install the sub chassis to the mechanism, and then tighten screws.
SA-AK23 0GCP Step 10 Remove 3 screws. Step 11 Put the capstan belt B as shown below. Step 12 Put the capstan belt A on the motor ass’y pulley.
SA-AK23 0GCP 10.15. Replacement for the cassette lid ass’y · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet Step 1 Lift up the lever upward, open the cassette lid ass’y. (For DECK1 and DECK2) Step 2 Push up the cassette lid ass’y in the direction of arrow. (For DECK1 and DECK2).
SA-AK23 0GCP 10.16. Rectification for tape jam problem · Follow the (Step 1) - (Step 2) of Item 10.3 - Disassembly of Top Cabinet Step 1 If a cassette tape cannot be removed from the deck (the tape is caught by the capstan or pinch roller during playback or recording), rotate the flywheel F in the direction of the arrow to remove it. Step 2 Push the lever upward and open the cassette lid ass’y. Remove the cassette tape.
SA-AK23 0GCP 11 Checking for major P.C.Bs Note: Checking of all major P.C.Bs (Main P.C.B., Panel P.C.B., Transformer P.C.B., Deck P.C.B., Deck Mechanism P.C.B. and Power P.C.B.) can be carried out using below procedures. For the disassemblin g procedures, refer to Section 10. 11.1. Checking of Main P.C.B. 1. Remove Top Cabinet and Rear Panel. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Connect FFC wires (CN2801 & CN2805) from CD Mechanism Unit.
SA-AK23 0GCP 11.2. Checking of Transformer P.C.B. 1. Remove Top Cabinet and Rear Panel. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Connect FFC wires (CN2801 & CN2805) from CD Mechanism Unit.
SA-AK23 0GCP 11.3. Checking of Panel, Deck & Deck Mechanism P.C.B. 1. Remove Top Cabinet. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Remove volume knob at Front Panel Unit. 5. Disassemble Panel P.C.B. 6. Disassemble Deck Mechanism Unit. 7. Use the extension cable (A) to reconnect (CN1001) Deck P.C.B. and (CN2803) Main P.C.B. 8. Use the extension cable (B) to reconnect (CP6401) Panel P.C.B. and (CN971) Deck Mechanism P.C.B. Service Tools Extension FFC (A) Deck P.C.B. - Main P.C.B. (B) Panel P.
SA-AK23 0GCP 11.4. Checking of Power P.C.B. 1. Remove Top Cabinet and Rear Panel. 2. Remove CD Lid. 3. Disassemble CD Mechanism Unit. 4. Remove 3 screws at Transformer P.C.B.. 5. Remove 2 screws at heat sink and 1 screw at Power P.C.B. 6. Flip the Power P.C.B. 7. Insulate the Power P.C.B. with insulation material to avoid short circuit. 8. Use the extension cable (A) to reconnect (CN1001) Deck P.C.B. and (CN2803) Main P.C.B. 9. Use the extension cable (B) to reconnect (CP6401) Panel P.C.B.
SA-AK23 0GCP 12 Self-Diagnostic Function 12.1. Self-diagnostic display This unit is equipped with a self-diagnost ic display function which, will display an error code corresponding to the problem occuring. Use this function when performing checking maintenance on the unit. 12.2. How to enter the Self-Diagnostic Function 12.3. Cassette Mechanism Test (For error code H01, H02, H03, F01) 1. Press “TAPE, DECK 1/2” to select Deck 2. 2.
SA-AK23 0GCP 3. Press to close the tray. wait until the tray is open. 4. Press “CD DIRECT PLAY (5)” and 5. Press and remove the CD. 6. Press to close the tray. 7. Press “n/STOP” to indicate Error Code. · If several problem exist, error code will change each time when “n/STOP” is pressed. (e.g. F15 → F26 → F16 ....etc). 12.5. To clear all Error code 1. Press and hold button for 5 seconds. 2. FL indicator shows “CLEAR” for 1 second and change to “T”. 12.6. To exit from Self-Diagnostic function 1.
SA-AK23 0GCP 12.8.3. Power supply related error detection No. 1 Abnormal Items POWER AMP output abnormal Error Display Method of Detection F61 During normal operation, if DCDET becomes ‘L’, normal POWER OFF process shall not be executed, PCNT shall be switched to ‘L’ immediately. GOODBYE shall not be displayed and the error display F61 will be displayed instead. 2 seconds after the F61 display, ECONO shall be set to ‘L’ and FL display shall be turned off.
SA-AK23 0GCP 13 CD Test Mode Function This CD test mode is provided to check CD unit without connecting to changer loading mechanism. This mode shall operate CD PLAY with CD unit being connected only and CD Automatic Alignment result is shown on FL display. 13.1. How to set CD test mode 13.2. CD Automatically Adjustment result indication Under CD test mode, pressing the numeric key ‘0’ on the remote controller will display the auto adjustment result.
SA-AK23 0GCP · It shall move up one counter when the above operations ends. The counter will reset to 00000 when 99999 is reached. · To exit CD aging test mode, press button, the tray will return to its PLAY position and power will be off. 13.4. Micon ROM Checksum and Version Display Mode 1. Functional Summary Display version number and calculated checksum of the micon software. 2. To enter into Micon ROM checksum and Version Display Mode. a. Enter into Self-Diagnos tic Mode (Refer to Section 12.2). b.
SA-AK23 0GCP 14 Measurements and Adjustments 14.1. Cassette Deck Section standard value. Bias voltage for Deck 2 Erase voltage for Deck 2 · Measurement Condition 14±4mV (Normal) 80mV (Normal) − Make sure head, capstan and press roller are clean. − Judgeable room temperature 20 ± 5 °C (68 ± 9°F) · Measuring instrument − EVM (DC Electronic voltmeter) − Digital frequency counter · Test Tape − Tape speed QZZCWAT gain adjustment (3 kHz, -10 Fig.2 dB); 14.1.1. Tape Speed Adjustment (Deck 1/2) 1.
SA-AK23 0GCP 9. Set AM-SG to 520kHz. 10. Receive 520kHz in the unit. 11. Adjust L2602 (OSC) so that the EVM-DC value is with 1.1±0.5V. Fig.6 14.2.2. AM RF Adjustment 1. Connect the instrument as shown in Fig. 7. 2. Set the unit to AM mode. 3. Set AM-SG to 520kHz. 4. Receive 520kHz in the unit. 5. Adjust Z2602 (OSC) so that the EVM-AC is maximized. 6. Set AM-SG to 600Hz. 7. Receive 600Hz in the unit. 8. Adjust Z2602 (ANT) so that the EVM-SG is maximized. Fig.7 14.3. Alignment Points 14.3.1.
SA-AK23 0GCP 15 Block Diagram OPTICAL PICKUP SEMICONDUCTOR LASER LPD Q7601 LD LASER POWER DRIVE B B PHOTO DETECTOR A A C B B B D B F F B E E B IC7003 AN8739SBTE2 FOCUS COIL/TRACKING COIL/ TRAVERSE MOTOR/ SPINDLE MOTOR DRIVE /RST 1 RESET SIGNAL GENERATOR FOCUS COIL F- 17 D4+ F+ 16 D4- 18 15 D3+ T+ 14 D3- TRACKING COIL M7301 M IN4 23 FOP TRACKING COIL DRIVE IN3 24 TRP IN1 6 TRVP NC T- TRAVERSE MOTOR FOCUS COIL DRIVE 11 D1+ 10 D1- TRAVERSE MOTOR DRIVE NC M730
SA-AK23 0GCP TO MAIN BLOCK MCLK BLKCK MDATA MLD STAT A B B CD_RST MICRO COMPUTER INTERFACE TIMING GENERATOR 47 48 43 49 AVSS2 AVDD2 45 PLLF MDATA 46 PLLF0 MCLK 44 IREF 64 DSLF 63 ARFIN 65 MLD NRST STAT 68 66 (PMCK) NTEST IOMODE X2 60 59 70 (SMCK) B 71 X1 X7201 TXTCK DSL/PLL/VCO TXTD DQSY B B A, B, C, D, E, F 27 30~35 B LD 37 LPD B A,B,C,D,E,F 29 LD 28 PD 36 DCDET 41 CAGC ARF 39 EFM DEMODULATION SYNC INTERPOLATION CIRC ECC CDROM ECC SPINDLE SERVO
SA-AK23 0GCP FM ANT Z2620 Q1 (RF AMP) 1 CF2601 7 MIXER Q3 5 AM ANT CF2602 Q2601 Q2 FM IF AMP Q4 BUFFER OSC D2602 L2601 6 L2602 8 B B (FM) RCH 22 23 24 ALC 21 AM OSC BUFFER 19 20 18 17 16 PILOT CANCEL STEREO SWITCH AM DET AM IF AM/FM IF BUFFER FM DET 13 PHASE DET S-CURVE FM IF 14 DECODER AM RM AMP AM MIX AGC LEVEL DET 15 COMP VCO TUNING DRIVE FF REG 5 4 ST 3 FF PILOT DET REG SD 2 1 FF 6 7 8 9 10 11 12 B IC2601 LA1833NMNTLM X2602 Z2602 FM/AM
SA-AK23 0GCP FL6601 FROM POWER TRANSFORMER FL DISPLAY 11~14, 16~29 1, 2, 30~40 FL0 FL DRIVER 10 XOUT 3 XIN ~CS 8 IC6601 C0HBB0000044 SDATA ~RESET FL13 SCK 9 FL12 3, 5~10, 12, 13, 15, 16, 18, 19 FL30 21, 23, 24, 26~40 5 6 IC1 C0GAM0000005 MOTOR DRIVE 8 VS 5 IN1 6 IN2 REG OUT1 2 OUT2 10 B VREF VCC GND M 4 7 1 RM1 Q1 B PLLDA D2 POWER SUPPLY CONTROL B Q2907 STAT SWITCH SW2 PUSH SW1 PUSH SW3 OPEN Q2936 ST/DO CD MOTOR SUPPLY SWITCH B PLLCLK Q2906 BLKCK
SA-AK23 0GCP IC1001 AN7348S-E1 P.B EQ/REC AMP/ ALC/TPS AMP LCH 24(23) (DECK 1) P.B.
SA-AK23 0GCP 7(8) IC2804 C0AABA000009 B1(2) DUAL OP-AMP OUT1(2) 2(6) 22(21) 1(7) 3(5) 5(6) 2(4) 32(31) FILTER A1(2) SEL1(2) REC1(2) FILTER IC2803 C1BB00000732 AUDIO SOUND PROCESSOR HP_L(R) 9(10) C1(2) SI CD SIGNAL E1(2) 18 SC 13(14) JK2801 AUX 17 Q2571 MUTING SWITCH B Q2701, Q2704~Q2706 SWITCH, LOW FREQUENCY AMP M B D2811 B D2901 Q2902 Q2501 D2332 B IC2802 C3EBDG000052 AUDIO MUTING CONTROL SWITCH B SWITCH Q2806 POWER RESET CONTROL SWITCH Q2901 SWITCH E-EPROM (NO
SA-AK23 0GCP 10(14) -IN_L(R) OUT_L(R) IC5802 RSN35H2B-P +VCC POWER HIC 11(13) +IN_L(R) -VCC AC DET LATCH 12 9 LCH 4(1) JK5952 LOW CH (6 W) 2 3 6 5 FILTER IN GND OUT GND -VCCM 8 B D5814 FILTER FILTER DC_DET Q5812, Q5813 Q5802, Q5805 DC DETECT SWITCH VOLTAGE SUPPLY/ CURRENT CONTROL SWITCH JK6551 HEADPHONE FAN HP _SW RCH Q5814 MUTE_H D5813 FAN HEADPHONE MUTING SWITCH Q5952 SYNC SYNCHRONISING SWITCH T5951 T5950 15V VOLTAGE REGULATOR D5954~D5957 Q5804, Q5806, Q5807 CURREN
SA-AK23 0GCP 16 Voltage Measurement 57
SA-AK23 0GCP 58
SA-AK23 0GCP 17 Schematic Diagram (All schematic diagrams may be modified at any time with the development of the new technology) Note: SW1 SW2 SW3 SW4 SW5 S951 S952 S971 S972 S975 S5950 S6101 S6102 S6103 S6104 S6105 S6106 S6201 S6202 S6203 S6204 S6205 S6206 S6207 S6208 S6209 S6210 S6301 S6303 S6304 S6305 S7201 VR6491 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Push switch Push switch Open switch CD switch Load switch Mode switch Half switch Mode switch Half switch Recinh_F switch V
SA-AK23 0GCP 17.1. (A) CD Servo Circuit SCHEMATIC DIAGRAM - 1 : +B SIGNAL LINE OPTICAL PICKUP CIRCUIT CD SERVO CIRCUIT Q7601 CP701 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 A GND B C7614 6.3V100 VREF LPD C7613 0.1 GND TT+ FF+ CN7001 R7329 1.5K R7328 18K R7349 15K R7327 1.5K C7335 0.
SA-AK23 0GCP SCHEMATIC DIAGRAM - 2 : +B SIGNAL LINE : CD SIGNAL LINE : CD-DA SIGNAL LINE CD SERVO CIRCUIT C7625 6.3V220 C7626 0.1 26 C7223 6.3V100 C7224 0.1 21 R7217 1K 23 C7225 1000P C7226 1000P 0.015 0.1 1000P 0.082 C7244 C7217 C7241 C7218 R7211 82K R7218 1K C7263 0.1 R7212 820 20 22 R7221 100 C7231 6.3V220 C7230 0.1 C7234 16V10 C7233 0.1 C7232 6.3V220 LCH OUT C7216 680P C7264 0.1 C7105 0.1 +3.3V 13 D.GND 12 LD SW 11 C7253 470P C7235 16V10 TX 15 C7243 +7.
SA-AK23 0GCP 17.2. (B) Main (Tuner) Circuit SCHEMATIC DIAGRAM - 3 : +B SIGNAL LINE : FM SIGNAL LINE : AM SIGNAL LINE : FM/AM SIGNAL LINE : FM OSC SIGNAL LINE : AM OSC SIGNAL LINE MAIN (TUNER) CIRCUIT R2604 1K TUNER PACK CIRCUITZ2620 5.6P 1000P C2604 1000P 3 10P 3.3P 2 R2606 470K CF2602 LT10.7MA5DTF 3 R2601 0 2 R2605 470 Q2601 Q2601 1000P 180P Q2606 1 3 390 R2607 330 B1AABC000003 FM IF AMP 4 390 220 100K 6 390 560K 5 C2601 0.01 2SC1675l1l2 4.
SA-AK23 0GCP 17.3. (B) Main Circuit SCHEMATIC DIAGRAM - 4 : +B SIGNAL LINE : PLAYBACK SIGNAL LINE : AUX SIGNAL LINE : -B SIGNAL LINE : RECORD SIGNAL LINE : MAIN SIGNAL LINE MAIN CIRCUIT Q2980 B1GDCFJJ0023 Q2978 B1GDCFJJ0023 Q2978 +15V REC_R D2813 B0ACCK000005 REC_L VREF+ /REC 0 SW5V R2976 W2917 ERJ3GEY0R00V +9V MOT10V R2977 0 /MTR DMT 6 MOGND MOT+B 7 REC_H 8 +15V 9 RECINR 10 RECINL 11 AFGND 12 PBR 13 DECK1_H 5 CD7.
SA-AK23 0GCP SCHEMATIC DIAGRAM - 5 TO PANEL CIRCUIT (CN6601) ON SCHEMA TIC DIAGRAM-9 5 4 3 R2267 33 R2269 33 SYS6V SYNC PCONT SW5V RMT PHOTO_1 VREF+ PHOTO_2 KEY1 KEY2 SSEQ_LED DECK2 KEY3 FL_CLK FL_DOUT FL_CS v_JOG_B FL_RST V_JOG_A MOT10V /PLG2 /HALF_1 /PLG1 /MODE_1 HP_R HP_L C2999 0.1 HP_L HP_R R2270 1 R2268 33 CN2806 C2753 0.1 C2751 0.
SA-AK23 0GCP SCHEMATIC DIAGRAM - 6 /HALF_1 1K 10K 10K R2843 R2842 R2841 /MODE_1 /PLG1 SW_LED /REC 10K R2844 /MTR /PLG2 4.
SA-AK23 0GCP SCHEMATIC DIAGRAM - 7 : +B SIGNAL LINE : AUX SIGNAL LINE : MAIN SIGNAL LINE : -B SIGNAL LINE : CD SIGNAL LINE : PLAYBACK SIGNAL LINE : FM/AM SIGNAL LINE : RECORD SIGNAL LINE MAIN CIRCUIT D2951 B0BC7R500001 +15V R2211 10K R2112 22K C2120 1 R2212 22K C2112 C2111 1500P 0.1 REC_L R2318 2.7K R2418 2.7K TO MAIN (TUNER) CIRCUIT (1A) ON SCHEMATIC DIAGRAM-3 +15V R2953 10K DO/ST R2317 100K R2111 10K C2951 0.01 TGND D2951 PBR PBL C2952 0.01 SD +9.0V DO/ST SD +7.
SA-AK23 0GCP 17.4. (C) Panel Circuit SCHEMATIC DIAGRAM - 8 : MAIN SIGNAL LINE : +B SIGNAL LINE : -B SIGNAL LINE PANEL CIRCUIT SYS6V S6210 POWER 6.8K R6209 R6208 4.7K 2.7K 1K 1K 1.2K JOG VOL R6207 R6102 R6103 R6104 S6207 C6492 100P R6491 47K VJOG_B VJOG_A B1GACFLL0007 2.2K S6303 1.8K SSEQ R6303 1K 1.2K S6202 TUNER R6302 1K S6201 REW / DOWN R6493 10K LED DRIVE REC R6304 1.2K CD VREF Q6457 S6304 FF / UP S6203 R6202 Q6457 R6492 47K DEMO/ DISPLAY R6305 1.
SA-AK23 0GCP SCHEMATIC DIAGRAM - 9 : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE PANEL CIRCUIT FL2 g1 FL2 P2 G1 P3 g2 P4 G2 P5 g3 P6 P7 P1 FL30 FL11 FL29 FL28 FL27 FL09 FL10 FL26 FL08 FL25 FL07 FL24 FL06 FL23 FL05 FL22 FL04 FL21 FL03 G3 P8 g4 G4 FL02 FL20 FL19 FL18 FL17 P9 FL16 G5 g5 FL15 FL01 FL00 FL14 g6 G6 FL13 P11 FL12 g8 G7 g7 FL11 FL10 g9 G8 FL09 FL08 FL07 G9 NC P10 P12 P13 P14 43 g10 8 9 10 11 12 13 14 15 16 17 18 19 20 21
SA-AK23 0GCP 17.5. (D) Transformer Circuit, (E) CD Detect Circuit, (F) Spindle Position Circuit & (G) CD Loading Circuit SCHEMATIC DIAGRAM - 10 : +B SIGNAL LINE : -B SIGNAL LINE TRANSFORMER CIRCUIT 1 VCC+ 2 TO POWER CIRCUIT (H5950/ W5950) ON SCHEMATIC DIAGRAM-11 3 VCC- FC4 FC3 D5953 5 6 D5951 A B A A: 240V B: 120V B T5950 G4C7AGK00007 R5965 12K AC_IN 3 4 0.1 AC GND 2 F2 250V 1.
SA-AK23 0GCP 17.6. (H) Power Circuit SCHEMATIC DIAGRAM - 11 : MAIN SIGNAL LINE : -B SIGNAL LINE : +B SIGNAL LINE POWER CIRCUIT IC5802 -IN_L GND -VCCM MUTE C AC DET LATCH OUT_L -VCC +VCC OUT_R 6 5 4 3 2 1 C5501 0.01 +IN_L 7 C5242 IN GND 8 820P 9 470P 10 C5442 +IN_R 11 470P 12 820P 13 C5240 14 C5440 -IN_R IC5802 RSN35H2B-P POWER HIC C5521 100V10 R5450 330K D5814 B0AACK000004 C5443 100V10 C5441 15P R5445 5.6K C5243 15P C5545 50V1 R5853 220K C5838 50V2.
SA-AK23 0GCP 17.7. (I) Deck Circuit & (J) Deck Mechanism Circuit SCHEMATIC DIAGRAM -12 : +B SIGNAL LINE : PLAYBACK SIGNAL LINE : RECORD SIGNAL LINE DECK CIRCUIT C1038 220P C1043 50V4.7 C1056 16V10 C1036 0.033 HI/LO CRO/NOR AB SW RIPPLE FILTER OUTPUT GND 7 8 9 10 11 12 C1033 0.018 C1045 10V22 VCC ALC T 13 REC/PB SW REC OUT R1032 10K 14 C1041 16V10 R1022 10K 4 15 6 C1039 220P C1031 10V100 C1023 1000P R1010 18K C1027 1000P R1016 C1037 50V3.
SA-AK23 0GCP SCHEMATIC DIAGRAM - 13 : PLAYBACK SIGNAL LINE : +B SIGNAL LINE R1098 10K 6 5 4 3 DMT BP1 2 1 CN1001 MOTOR 7 DECK1_H 8 MO+B +B 9 REC_H 11 10 RECINR AFGND PBL 13 12 PBR 14 RECINL DECK CIRCUIT MO GND TO MAIN CIRCUIT (CN2803) ON SCHEMATIC DIAGRAM-4 : RECORD SIGNAL LINE R1060 390 R1057 2.2K R1091 0 R1092 0 R1049 0 R1084 2.2K R1097 10K Q1017 B1AARC000002 C1049 3300P 1 1 2 2 + - M W1002 MOTOR SWITCH R1086 2.
SA-AK23 0GCP 18 Printed Circuit Board Note: Circuit board diagrams may be modified at any time with the development of new technology. 18.1. (A) CD Servo P.C.B.
SA-AK23 0GCP 18.2. (B) Main P.C.B. A C D E F G B MAIN P.C.
SA-AK23 0GCP H W2257 R2908 R2907 R2901 R2909 C2903 R2933 W2260 C2904 W2259 W2261 B CA A C2907 4 2 5 3 W2266 W2268 W2267 W2208 W2902 W2901 W2280 C2905 R2861 2 W2283 5 6 7 8 80 81 3 4 W2209 R2916 C2999 1 W2298 W2281 R2927 W2272 R2912 R2914 C2817 E W2270 W2271 R2862 W2273 R2925 R2921 B W2269 W2504 W2508 C2816 C2906 W2276 W2904 R2929 B Q2907 R2856 W2282 1 9 10 11 12 13 14 W2207 15 16 R2846 R2845 R2811 17 18 19 W2903 100 51 IC2801 1 R2801 R28
SA-AK23 0GCP 18.3. (C) Panel P.C.B. A D E G F PANEL P.C.
SA-AK23 0GCP G H I J FL6601 15 20 25 30 35 40 K CN6601 43 1 3 R6601 C6601 R6602 11 13 15 17 19 21 23 25 10 12 14 16 18 R6458 27 29 20 22 24 26 28 30 D6458 W6075 C6636 W6063 W6062 IC6601 1 9 8 W6089 21 40 7 6 J6902 W6101 30 31 4 M W6105 5 2 W6100 L W6102 20 W6083 W6076 W6082 W6085 S6301 POWER W6065 R6611 W6033 11 W6087 10 W6103 W6094 W6080 C6632 W6059 W6081 R6399 W6060 W6022 W6092 W6093 W6066 R6199 W6077 W6071 J6108 R6303 W6031 S6303
SA-AK23 0GCP 18.4. (D) Transformer P.C.B. A 1 B D C D E F G TRANSFORMER P.C.B (REPX0468D) CAUTION RISK OF ELECTRIC SHOCK AC VOLTAGE LINE. PLEASE DO NOT TOUCH THIS P.C.B 2 F1 250V 1.
SA-AK23 0GCP 18.5. (E) CD Detect P.C.B., (F) Spindle Position P.C.B., (G) CD Loading P.C.B. & (K) Tuner Pack P.C.B. A 1 B C D E F G G CD LOADING P.C.B (REP2578A-N) IC1 2 4 7 6 5 9 8 10 14 2 1 R1 3 C1 2 W1 W2 1 SW3 E C B J3 J1 11 9 4 6 7 5 2 3 2 3 4 1 CN1 Q1 SW1 J4 SW2 J2 C2 8 10 1 13 D2 OPEN 12 3 PUSH PUSH 3 M - 4 PbF 5 E F CD DETECT P.C.B (REP2578A-N) 6 D1 1 2 3 SPINDLE POSITION P.C.
SA-AK23 0GCP 18.6. (H) Power P.C.B. A 1 2 B H C D E G F POWER P.C.
SA-AK23 0GCP G H I J K L M IC5802 W5807 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R5801 W5870 W5869 C5803 R5806 C5802 W5855 C5443 R5451 R5545 C5240 R5546 R5250 C5243 C5501 C5242 W5822 W5833 W5862 B 1-LG B C C E E 2-RG W5847 SPEAKER C5447 C5521 C5444 R5445 3-L R5245 C5820 W5868 JK5952 W5803 Q5813 Q5812 R5455 W5874 W5816 W5818 W5819 R5446 W5844 D5813 4-R C5545 R5854 R5246 W5878 R5856 D5814 C5846 W5861 1 2 3 4 5 6 7 8 9 10 11 12 R585
SA-AK23 0GCP 18.7. (I) Deck P.C.B. & (J) Deck Mechanism P.C.B.
SA-AK23 0GCP 19 Wiring Connection Diagram FM ANT AUX AM ANT PbF K TUNER PACK P.C.B CN2809 SOLDER SIDE 12 To Fan CN2810 CN5801 ........ B MAIN P.C.B 1 1 1 12 .......... PbF 12 SOLDER SIDE CN2805 ...... ...... 1 2 E CD DETECT P.C.B 13 14 SOLDER SIDE W2 123 1. 3 1314 PbF W2 ...... ...... H POWER P.C.B SOLDER SIDE 12 CN1 1 .. CN2808 4 CN2801 12 W1 1. . 4 16 15 F SPINDLE POSITION P.C.B ........... ........... PbF .......... W1 1 CN2806 CN2803 2 1 1 ........
SA-AK23 0GCP 20 Illustration of IC’s, Transistors and Diodes C2CBJG000565 (100P) C0HBB0000044 (48P) AN7348S-E1 (24P) MN6627953HB (80P) LA1833NMNTLM (24P) LC72131MDTRM (20P) C1BB00000732 (32P) C0AABA000009 C1AA00000612 5 1 8 1 RSN35H2B-P AN8739SBTE2 1 26 24 3 21 3 20 1 14 E 6 7 1 13 4 C 14 10 1 B1BACG000023 B1BCCG000002 2 1 4 5 1 CNB13030R2AU C0GAM0000005 B 2SB0709AHL 2SD0601AHL B1ADCF000001 B1ABCF000131 B1ABCE000016 B1GDCFJJ0023 B1GBCFJJ0051 B1GFGCAA0001 B1AAGC000007 B1GACF
SA-AK23 0GCP 21 Terminal Function of IC’s 21.1. IC7002 (MN6627953HB) Servo processor/ Digital signal processor/ Digital filter/ D/A converter 1 2 3 4 Pin No.
SA-AK23 0GCP Pin No. 13 Mark D2+ O I/O 14 D3- O 15 D3+ O 16 D4- O 17 D4+ O 18 19 20 21 22 23 24 25 26 N.C. PGND2 PVCC2 VCC VREF IN4 IN3 RSTIN N.C. I I I - Function Motor driver (2) forward- action output Motor driver (3) reverse- action output Crystal oscillating circuit input (f = 16.
SA-AK23 0GCP 22 Troubleshooting Guide 87
SA-AK23 0GCP 23 Parts Location and Replacement Parts List Notes: · Important safety notice: Components identified by mark have special characteristic s important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used. When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list.
SA-AK23 0GCP 23.1. Deck Mechanism (RAA4502-S) 23.1.1.
SA-AK23 0GCP 90
SA-AK23 0GCP 23.1.2. Deck Mechanism Parts List Ref. No. 101 102 103 104 105 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 128 129 130 130-1 132 133 133-1 133-2 134 135 136 137 138 139 Part No.
SA-AK23 0GCP 23.2. CD Loading Mechanism (RD-DAC026-S) 23.2.1.
SA-AK23 0GCP 93
SA-AK23 0GCP 23.2.2. CD Loading Mechanism Parts List Ref. No. 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 341 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 358-1 358-2 358-3 358-4 358-5 358-6 358-7 358-8 358-9 358-10 359 360 361 362 Part No.
SA-AK23 0GCP 23.3. Cabinet 23.3.1.
SA-AK23 0GCP 96
SA-AK23 0GCP 23.3.2. Cabinet Parts List Ref. No. 1 2 3 4 5 6 7 7-1 9 10 11 12 13 14 16 17 Part No.
SA-AK23 0GCP Ref. No. D1003 D1004 D2601 D2602 D2703 D2704 D2705 D2802 D2804 D2811 D2813 D2901 D2904 D2936 D2951 D5801 D5802 D5803 D5804 D5805 D5807 D5808 D5809 D5813 D5814 D5950 D5951 D5952 D5953 D5954 D5955 D5956 D5957 D5958 D5959 D5960 D5961 D5962 D5964 D5965 D5966 D5980 D5981 D5988 D6457 D6458 D6635 Part No.
SA-AK23 0GCP Ref. No. Part No. X7201 H2B169500002 Part Name & Description RESONATOR Remarks [M] Ref. No. W2926 W2927 W2928 W2929 W2930 W5815 W7001 W7002 W7003 W7004 W7005 W7006 W7007 W7008 W7009 W7010 W7011 W7012 W7013 W7014 W7015 W7016 W7017 W7018 W7019 W7020 W7021 W7022 W7023 W7024 W7025 W7027 W7028 W7033 W7034 W7040 W7041 W7042 W7043 W7044 W7050 W7051 W7052 W7053 W7054 W7055 DISPLAY TUBE FL6601 A2BD00000111 FL [M] FUSES F1 F2 K5D252BLA013 K5D122BLA014 2.5A FUSE FUSE 1.
SA-AK23 0GCP Ref. No. R1012 R1013 R1014 R1015 R1016 R1017 R1018 R1019 R1020 R1022 R1024 R1025 R1026 R1027 R1028 R1029 R1030 R1031 R1032 R1035 R1040 R1049 R1050 R1055 R1057 R1060 R1084 R1085 R1086 R1087 R1090 R1091 R1092 R1097 R1098 R1099 R1100 R1101 R2101 R2102 R2103 R2106 R2107 R2108 R2111 R2112 R2113 R2116 R2117 R2118 R2141 R2142 R2143 R2152 R2154 R2166 R2167 R2168 R2169 R2170 R2171 R2181 R2184 R2201 R2202 R2206 R2207 R2211 R2212 R2216 R2217 R2241 R2242 R2243 Part No.
SA-AK23 0GCP Ref. No. R2646 R2651 R2652 R2701 R2702 R2704 R2705 R2706 R2707 R2708 R2709 R2710 R2711 R2712 R2713 R2714 R2715 R2801 R2802 R2803 R2804 R2805 R2806 R2807 R2810 R2811 R2817 R2818 R2819 R2820 R2821 R2822 R2823 R2824 R2831 R2834 R2841 R2842 R2843 R2844 R2845 R2846 R2856 R2857 R2858 R2859 R2860 R2861 R2862 R2867 R2876 R2877 R2878 R2881 R2882 R2883 R2886 R2891 R2892 R2899 R2901 R2902 R2903 R2907 R2908 R2909 R2910 R2911 R2912 R2913 R2914 R2915 R2916 R2917 Part No.
SA-AK23 0GCP Ref. No. R5832 R5834 R5847 R5853 R5854 R5855 R5856 R5858 R5951 R5952 R5954 R5955 R5956 R5957 R5958 R5960 R5961 R5965 R5971 R5972 R6102 R6103 R6104 R6105 R6106 R6111 R6199 R6202 R6203 R6204 R6205 R6206 R6207 R6208 R6209 R6210 R6302 R6303 R6304 R6305 R6399 R6401 R6402 R6403 R6404 R6405 R6406 R6411 R6412 R6415 R6416 R6421 R6425 R6457 R6458 R6491 R6492 R6493 R6601 R6602 R6603 R6604 R6611 R6631 R6632 R7102 R7104 R7105 R7106 R7144 R7211 R7212 R7214 R7217 Part No.
SA-AK23 0GCP Ref. No. C1056 C1057 C1058 C1059 C2101 C2102 C2103 C2106 C2107 C2108 C2111 C2112 C2114 C2116 C2117 C2118 C2119 C2120 C2121 C2126 C2131 C2136 C2141 C2142 C2151 C2166 C2181 C2183 C2184 C2201 C2202 C2203 C2206 C2207 C2208 C2211 C2212 C2214 C2216 C2217 C2218 C2219 C2220 C2221 C2226 C2231 C2236 C2241 C2242 C2251 C2266 C2281 C2283 C2284 C2301 C2302 C2311 C2312 C2401 C2402 C2411 C2412 C2501 C2520 C2521 C2581 C2582 C2583 C2584 C2585 C2588 C2601 C2602 C2603 Part No.
SA-AK23 0GCP Ref. No. C2906 C2907 C2936 C2951 C2952 C2976 C2977 C2998 C2999 C5240 C5242 C5243 C5244 C5441 C5442 C5443 C5444 C5447 C5501 C5521 C5545 C5547 C5802 C5803 C5804 C5805 C5806 C5807 C5808 C5809 C5810 C5811 C5812 C5813 C5814 C5820 C5838 C5840 C5846 C5880 C5950 C5951 C5952 C5953 C5954 C5955 C5956 C5957 C5958 C5959 C5960 C5961 C5962 C5963 C5964 C6481 C6491 C6492 Part No.
SA-AK23 0GCP 23.6.
