Datasheet

ManualsBrandsPANASONIC ManualsRelaysNarrow, Compact Relay Housing With 4 Outputs

RT-3 (Power PhotoMOS Relay type)

743

TYPES

Note: Only for use with Power PhotoMOS standard type relays. Cannot be equipped with PA relays.

RATINGS

1. Input ratings (per relay)

Note: This product has a built-in input current limiting resistor; therefore, it is not necessary to externally connect a resistor to the input. The input voltage

can be applied directly.

2. Output ratings (per relay, at 25°C 77°F)

Notes: 1. During 4-point operation, the rating of each relay is also as shown above.

2. The load current varies depending on ambient temperature. Refer to the Load current vs. ambient temperature characteristic data.

SLIM, SPACE-SAVING

4-POINT UNIT RELAY WITH

POWER PhotoMOS RELAY

RT-3 UNIT RELAY

(Power PhotoMOS Relay type)

Type Rated input voltage Part No.

Packing quantity

Inner carton Outer carton

Power PhotoMOS Relay (DC only)

(Equipped with AQZ102)

12 V DC RT3SP1-12V

1 pc. 20 pcs.

24 V DC RT3SP1-24V

Power PhotoMOS Relay (AC/DC dual use)

(Equipped with AQZ204)

12 V DC RT3SP2-12V

24 V DC RT3SP2-24V

Part No. Rated input voltage

Operate voltage

(at 25°C 77°F)

Release voltage

(at 25°C 77°F)

Input current

(during application of

rated input voltage)

(at 25°C 77°F)

Allowable variation of

rated input voltage

(at –20°C to +55°C

–4°F to +131°F)

RT3SP1-12V

12 V DC

Max. 9.5 V DC

(5.1 V typ.)

Min. 3.0 V DC

(5.0 V typ.)

6.2 mA typ.

90% to 110% of rated

input voltage

RT3SP2-12V

RT3SP1-24V

24 V DC

Max. 15.0 V DC

(6.8 V typ.)

Min. 3.5 V DC

(6.5 V typ.)

6.7 mA typ.

RT3SP2-24V

Part No. Equipped relay Maximum load voltage Recommended voltage Continuous load current Peak load currant

RT3SP1-12V

AQZ102

(DC only)

60 V

(DC)

0 to 30 V (DC) 2 A (DC)

9 A

(100 ms 1 shot)

RT3SP1-24V

RT3SP2-12V

AQZ204

(AC/DC dual use)

400 V

(DC, AC peak value)

0 to 200 V (DC)

0 to 125 V (AC)

0.3 A

(DC, AC peak value)

1.5 A

(100 ms 1 shot)

RT3SP2-24V

RoHS Directive compatibility informatio

http://www.nais-e.com/

FEATURES

• Space-saving type with four

independent points on a base

measuring 33 × 67 mm 1.299 × 2.638

inch. This contributes to a more

compact control panel.

• Power PhotoMOS relays, for high

reliability and long life, is installed.

This type is equipped with Power

PhotoMOS relays which have a

reputation for high reliability and long

life. Helps make devices maintenance-

free.

• Can be mounted on a DIN rail or

mounted directly (by screw).

• Equipped with an LED display to

allow easy confirmation of operation.

• Incorporates a cross connection

preventing diode.

• Relay installation and removal can

be easily accomplished with the

removal key accessory.

• Includes a cover as standard

equipment for increased safety.

• The unit color of the Power

PhotoMOS Relay type is pale

lavender.

The unit color of the PA Relay type is

titanium gray.

Summary of content (9 pages)

PAGE 1
RT-3 (Power PhotoMOS Relay type) SLIM, SPACE-SAVING 4-POINT UNIT RELAY WITH POWER PhotoMOS RELAY RT-3 UNIT RELAY (Power PhotoMOS Relay type) FEATURES • Space-saving type with four independent points on a base measuring 33 × 67 mm 1.299 × 2.638 inch. This contributes to a more compact control panel. • Power PhotoMOS relays, for high reliability and long life, is installed. This type is equipped with Power PhotoMOS relays which have a reputation for high reliability and long life.
PAGE 2
RT-3 (Power PhotoMOS Relay type) PERFORMANCE Item Breakdown voltage Performance Between input and output 2,000 Vrms for 1 min. Between different terminals (between relays, both ways) 1,500 Vrms for 1 min. Insulation resistance Min. 100 MΩ (Using 500 V DC megger, measuring same place as breakdown voltage.) Vibration resistance (destructive) 10 to 55 Hz at double amplitude 1 mm .039 inch Shock resistance (destructive) Min.
PAGE 3
RT-3 (Power PhotoMOS Relay type) Lord current vs. ambient temperature characteristics 2 AQZ102 AQZ105 AQZ205 1 Load current, A AQZ202 AQZ107 AQZ207 AQZ104 AQZ204, AQZ404 –20 –10 0 10 20 30 40 50 60 –4 14 32 50 68 86 104 122 140 Ambient temperature, °C °F DIMENSIONS mm inch Schematic 33±0.6 1.299±.024 Input terminal portion Input side 8.4 .331 13+ 14+ 15+ 16+ 9– 10– 11– 12– LED1 R2.1 .083 2-M4 .157 screw mounting position 7.4 .291 LED4 16-M3 .118 terminal screw LED3 6.2 .
PAGE 4
CAUTIONS FOR USE CAUTIONS FOR USE 1. Never install modules (relays) into this product other than those designated. Doing so will cause malfunction, breakdown, and breakdown of the connected product. 2. Physical Impact If a unit is dropped be sure to check its external appearance and characteristics before using it. 3. The operation and return voltage values when equipped with PA relays are based on the relay terminals being face down. 4.
PAGE 5
CAUTIONS FOR USE 9. Transporting and storage 1) If the product is subjected to extreme vibration while being transported, the relays may become detached, the lead may become bent, and the unit may become damaged. Handle the inner and outer boxes with care. 2) If the product is stored in an extremely adverse environment, visible defects and deterioration of performance characteristics may result. We recommend the following storage conditions. • Temperature: 5 to 30°C 41 to 86°F • Humidity: Max. 60% R.H.
PAGE 6
RT-3 (PA Relay type) SLIM, SPACE-SAVING RELAY TERMINAL FOR 4-POINT OUTPUT RT-3 UNIT RELAY (PA Relay type) FEATURES • Space-saving type with four independent points on a base measuring 33 × 67 mm 1.299 × 2.638 inch. This contributes to a more compact control panel. • PA relays, which have high sensitivity Au clad twin contacts, is installed. PA relays, 5 mm .197 inch wide, is installed.
PAGE 7
RT-3 (PA Relay type) PERFORMANCE Item Breakdown voltage Performance Between input and output 2,000 Vrms for 1 min. Between different terminals (between relays, both ways) 1,500 Vrms for 1 min. Insulation resistance Min. 100 MΩ (Using 500 V DC megger) Vibration resistance Shock resistance destructive 10 to 55 Hz at double amplitude 1 mm .039 inch functional 10 to 55 Hz at double amplitude 1 mm .039 inch destructive Min. 196 m/s2 {20G} Min.
PAGE 8
CAUTIONS FOR USE CAUTIONS FOR USE 1. Never install modules (relays) into this product other than those designated. Doing so will cause malfunction, breakdown, and breakdown of the connected product. 2. Physical Impact If a unit is dropped be sure to check its external appearance and characteristics before using it. 3. The operation and return voltage values when equipped with PA relays are based on the relay terminals being face down. 4.
PAGE 9
CAUTIONS FOR USE 9. Transporting and storage 1) If the product is subjected to extreme vibration while being transported, the relays may become detached, the lead may become bent, and the unit may become damaged. Handle the inner and outer boxes with care. 2) If the product is stored in an extremely adverse environment, visible defects and deterioration of performance characteristics may result. We recommend the following storage conditions. • Temperature: 5 to 30°C 41 to 86°F • Humidity: Max. 60% R.H.