Panasonic INSTALLATION INSTRUCTIONS Ventilating Fan Model No. RG-C811A, RG-C811HA READ AND SAVE THESE INSTRUCTIONS Thank you for purchasing this Panasonic product, Please read these Instructions carefully before attempting tn install, operate or service the Panasonic product. Please carefully read the “GENERAL SAFETY INFORMATION" Failure to comply with instructions could readout in personal Injury or property damage.
GENERAL SAFETY INFORMATION (CONTINUED) A WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only In the manner Intended by the manufacturer. If you have any questions, contact the manufacturer. Before servicing or cleaning unit, switch power off at service panel and lack the service disconnecting means 0 10 prevent power from bang switched on accidentally.
GENERAL SAFETY INFORMATION (CONTINUED) A CAUTION © Da not Install this ventilating fan In a location whee the Interior room temperature may exceed 104 °F (40 °C). Marks sure that the strict service supply voltage Is AC 120: V 60 Hz, Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupational Safety and Health Administration (OSHA) Ways disconnect the power source before working on or near the fan, motor or Junction box.
UNPACKING Unpack and carefully remove the uit from carton. For to the Supplied Accessories fist tn verify that all pearls ara SUPPLIED ACCESSORIES Part name Appearance Quantity Part name Appearance Quantify installation rie + intros / 3 + Ware Shoat Flo Z Fast™ soa Thermometer {with 4 ling Grimes tapping straws ! sore 4 “5T4.2020) = DIMENSIONS RG-CB11A 11/268) Unit: inches {mm} T .
DIMENSIONS (CONTINUED) [1 RG-CB11HA Unit: inches (mm) No.
OPERATION (RG-C811HA only) Power oN i OFF switch +1 The product will continue to run for about 20 minutes after the sensor detects that Condensation 5 %RH the humid lower than the satin humidity eating bore stopping sensor | “Environment humidity ; Dolly : : i Run : ration wl | i Product : “| stop * Stop § Note: 1. The power switch shad be left on at ail times. 2 The product wil aloe run when the humidity es rapidly but doss nt reach the humidity trigger sting, and then stop after the time delay. 3.
INSTALLATION (RETROFIT) (CONTINUED) 1 Remove adapter from fan body @® Disconnect plug connector from the receptacle and remove adapter from fan body by removing the machine screw (4X2) before Installation. Unt: Inches Clare duct nf: Inches fmm} 2 Remove existing fan Holst (3) Remove the existing fan and cut the Gelling opening according to the required dimensions.
INSTALLATION (RETROFIT) (CONTINUED) (1) Remove screw from Junction box cover to remove the knock-out hole and secures consult or stress hellfire to junction box knock-out holey. ®@ Install the circular exhaust duct and secure It with clamps or ties and seal It with mastic or approved fol taps. A 4 Inch circular duct Is needed to connect to the relevant part of the adapter. (3) Regor to WIRING DIAGRAM (Page 5). Follow a the local satirical safety codes as well es the National Electrical Code (NECK.
INSTALLATION (RETROFIT) (CONTINUED) 's Sealing (once tan body is mounted and secures, fil gap between flange and calling with caulk or other sealant to prevent alr leakage. (2) Dust Pick-A-Fiow™ swatch. (Refer to explanation under FEATURES). (Page 6} Install grille 7 9 [S—— ® _ wounding spring @® Insert the mounting springs into the soot aa shown to mount grille to fan body. Grille.
INSTALLATION (NEW CONSTRUCTION) (CONTINUED) @ Extend bracket 10 the other joist. @ Install bracket to Joist by using 2-preinstalled tapping screws. 2 Tapping screws Sig (6T4.2x20) ® 3 Follow steps from “RETROFIT” Installation @ Follow the steps “INSTALLATION (RETROFIT). MAINTENANCE (CLEANING) A WARNING 0 Disconnect power source before waking on unit, A CAUTION Routine maintenance must be den every year. Do hot Immerse motor In water when cleaning. Please wear gloves during the cleaning work.
MAINTENANCE (CLEANING) (CONTINUED) 2 Maintenance of unit Clean grille. (Don't put into hot water. Use non-abrasive Kitchen detergent, wipe dry with clean cloth) NOTE: The rile should be dry afire cleaning Remove dust and dirt from fan body using & vacuum cleaner. @ Lingual a cloth dampened with kitchen detergent, ram ova any dirt from fan body. Wipe dry with clean cloth.
Panasonic Corporation of North America Panasonic Ventilating Fan Nona, NJ 07102 Limited Warranty Paganini; Corporation of North America (the Warrant) wil, et its dais discretion, carapace this product wth nsw pert or exchange tis product, free of sangs, bn the USA, In the Levant of defects In material or workmanship In accordance to the following: ALL Parts: For period of 3 arroyo (36 moth) DC Motor: Far period of 8 eraser (72 months) LED Light Unit: For a period of 5 years (60 more} Service In the USA, can
