Digital Video Camcorder Operating Instructions Models No. PV-DV202 PV-DV402 [ PV-DV402 shown ] Mini Before attempting to connect, operate or adjust this product, please read these instructions thoroughly. LSQT0597A DV202_402PN.p 1-4.
Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information below. The serial number is on the tag located on the underside of your Palmcorder. Be sure to retain this manual as your convenient Palmcorder information source. Date of Purchase Dealer Purchased From Dealer Address Dealer Phone No.
Important Safeguards 11. Grounding or Polarization — This video unit may be equipped with either a polarized 2-wire AC (Alternating Current) line plug (a plug having one blade wider than the other) or 3-wire grounding type plug, a plug having a third (grounding) pin. The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug.
Table of Contents Before Use Things You Should Know ................................................................................................ 2 Important Safeguards ..................................................................................................... 3 Precautions ..................................................................................................................... 4 Before Using ..........................................................................................
Before Using This Operating Instructions book is designed for use with models PV-DV202 and PV-DV402. The PV-DV402 is the model used for illustrative purposes. Features may vary, so please read carefully. Differences between models Model Number LCD Monitor PV-DV202 PV-DV402 63.5 mm (2.5 inch) Liquid Crystal Display MagicVu IR Filter (0Lux) MIC IN EXTERNAL 88.9 mm (3.5 inch) Liquid Crystal Display NO YES NO YES Unpack your Palmcorder 1 pc. AC Adaptor (PV-DAC11) with AC Cable and DC Cable 1 pc.
Before Using Record Speed/Playback Time Cassette type Record Speed/ Playback time LP SP AY-DVM30EA 30 minutes 45 minutes AY-DVM60EA 60 minutes 90 minutes AY-DVM80EA 80 minutes 120 minutes Erase Protection Cassettes have a sliding record tab to ensure recordings are not accidentally erased. 1 To prevent accidental erasure: Slide the tab to the left (open). record tab 2 To record again: Slide the tab to the right (close).
Before Using Attaching the Shoulder Strap 1 2 Adjust the Length 1 2 Undo the two strap ends from their buckles. Thread the strap ends through the Strap Attachment Rings. Loosen the strap from the Buckle and create a loop. Pull the strap firmly through the Buckle to shorten or lengthen the strap. 1 OR 3 Reinsert the strap ends through their buckles. • Make sure the straps are not twisted. 2 3 1 Lens Cap Hand Strap Adjust the length of the Hand Strap to the size of your hand as illustrated.
Before Using Using the Built-in Light Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to CAMERA or M-CARD. 1 Before Use To brighten the natural colors in a scene. Hold down LIGHT for more than 0.7 seconds to turn ON or OFF. • “ ” will appear on the screen. Built-in Light Note • Using Light reduces battery time. • Provide adequate ventilation if using Light in a hot environment for a long time. • Set LIGHT to OFF when not in use.
Before Using Replace the Battery B 1 While pressing the tab in the direction of the arrow (A) with your fingernail, pull out the Battery Tray (B). A + 2 3 Insert the battery into the Battery Tray with the facing up. Do not reverse the polarity. + mark Insert the Battery Tray. Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may present a risk of fire or explosion. Caution: battery may explode if mistreated. Dispose of used battery properly.
Quick Guide Before you begin Insert the Battery Pack Before Use • Charge the Battery. (p. 14) Protection Film Note 2 • Remove the Protection Film before use. 1 1 Insert the Battery Pack and slide it up until it locks with a click. Insert Cassette These Palmcorders are equipped with the Easy Cassette Eject System so it is easy to insert or remove tapes, even when on a tripod. (p. 7) 1 2 Press LCD-OPEN to unlock the LCD monitor, and swing it fully open.
Quick Guide Camera Recording When the LCD monitor is fully open, the Viewfinder automatically turns OFF. 1 2 Set POWER to CAMERA. Adjust the Vision Adjustment Control to your eyesight. Viewfinder 180° 90° 4 Press REC/PAUSE to start recording. Press REC/PAUSE again to pause recording. To Watch Playback in the LCD (Liquid Crystal Display) When the LCD monitor is fully open, the Viewfinder automatically turns OFF. 3 LCD Monitor Press LCD-OPEN to unlock the LCD monitor.
Quick Guide Before you begin Insert Memory Card* Before Use • Charge the Battery. (p. 14) *Memory Card: MultiMediaCard or SD Memory Card (p. 94) • Be sure to insert the Memory Card before using the Card PhotoShot. (p. 48) Below is a list of memory cards which can be used in this Palmcorder. Memory Card Capacity SD Memory Card (RP-SD008BMKO) (supplied) 8 MB MultiMediaCard (SanDisk brand) 8 MB, 16 MB SD Memory Card (optional) (p.
Supplying Power Charge the Battery Pack on the AC Adaptor 1 2 POWER Lamp 3 CHARGE Lamp Connect and plug in the Power Cord as shown. • POWER Lamp will light. • Remove the DC Cable, if attached, from the adaptor. Attach the Battery as shown to charge. • CHARGE Lamp lights up. It goes out when charging is complete (approx. 1 hour). Expect approx. 1 hour 30 minutes of operation (EVF usage) when fully charged. Remove the Battery. Slide the Battery out and then lift up.
Supplying Power Battery Care To avoid damage to the Battery: • Charge only with specified charger. • Charge the Battery within an ambient temperature range of 10 °C (50 °F) and 30 °C (86 °F). • The Battery may be warm after charging or just after use. This is normal. • Do not use an insufficiently charged or worn out Battery. • If charging is done in extreme low or high temperatures, Battery charge time increases. • Do not drop or jar the Battery. • Use the Battery with specified models only.
Setting the Clock Set the Date and Time The date and time is calculated, including leap year, up to DEC 31 2089. Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to CAMERA or VCR. 1 Press MENU to display the Camera or VCR mode menu screen. (p. 17) [ CAMERA MENU ] [ VCR MENU ] 2, 3, 4 JOG KEY 1MENU .
Using the Palmcorder Menu Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to CAMERA or VCR. 2, A, B, C Displaying the MENU 1 2 Press MENU to display the CAMERA or VCR menu (according to the POWER setting). Rotate JOG KEY to select a menu item. Setting the MENU Items (EX. VCR Mode menu) A B Press JOG KEY to set your selection. Rotate JOG KEY to select a menu item. JOG KEY 1, D MENU C D CAMERA Main menu 1 : D. FUNCTION CAMERA FUNCTION menu is displayed.
Camera Recording Simple Recording Before you begin Remove the lens cap and clip it to the hand strap. • Connect the Palmcorder to a power source. (pp. 14, 15) • Insert a cassette with the record tab closed. (p. 7) 1 2 Clip here EVF REC/PAUSE mode 3 4 POWER Lamp 1, 5 POWER 5 2Vision Set POWER to CAMERA. • The POWER Lamp lights red. • Be sure POWER is fully turned to the CAMERA position. With the Viewfinder Eye Cup held up against your eye, adjust the Vision Adjustment Control to your eyesight.
Camera Recording Using the LCD Monitor The LCD (Liquid Crystal Display) monitor can be used while recording. 1 2 1LCD-OPEN 3 90° Swing the LCD monitor fully open and adjust the viewing angle. • The LCD monitor will automatically turn on. • When the LCD monitor is completely closed, it will shut off automatically to save power. • Adjust the LCD Brightness and/or color of the LCD monitor if necessary. Please refer to “To adjust the LCD/ EVF BRIGHTNESS or COLOR” below. Start recording.
Camera Recording Digital PhotoShot Mode Use this feature to record a seven second (approx.) still image on the tape from the current camera picture. Audio is also recorded for on-the-spot narration. Or, you can add narration later with the Audio Dubbing feature to make an interesting slide show, etc. (p. 44) 1 2 Set POWER to CAMERA. Press PHOTOSHOT in Record/Pause mode. “PHOTO” will appear in the EVF or the LCD monitor.
Camera Recording Zoom You can gradually zoom in for close ups or zoom out for wide angle shots. 2POWER 1 2 ZOOM 1POWER Set POWER to CAMERA. Zoom slowly : by lightly pressing the “T” (Telephoto) or the “W” (Wide Angle) side of the POWER ZOOM. Zoom quickly: by applying more pressure. Start recording. Note • The zooming speed ranges from a slow 17 seconds to a fast 1.5 seconds according to the amount of pressure applied to the POWER ZOOM.
Camera Recording Recording Check To playback the final few seconds of the last recorded scene in the REC/PAUSE mode. 1RECORDING CHECK 1 Press RECORDING CHECK briefly in the REC/PAUSE mode. The [CHK] indication appears. After checking, the Palmcorder returns to the REC/PAUSE mode. • For Recording Check, the Palmcorder must be in the same mode (SP or LP) as was used for recording, otherwise the playback picture is distorted.
Special Effect Features CINEMA Mode You can record a picture compatible with a wide-screen TV equipped with an S2 picture terminal. 3, 4 JOG KEY 1 2 3 1POWER 2MENU 5REC/PAUSE 5 Backlight Use when recording a subject that is darker than the surrounding scene, in a shadowed area, or when the light source is behind your subject. 1 2 3 1POWER Press MENU to display the CAMERA mode menu screen. Rotate JOG KEY to select ADJUST , then press JOG KEY to display the CAMERA ADJUST menu screen.
Special Effect Features Program AE The Auto Exposure feature can be used to make quality recordings in a variety of scene situations. Note • When MagicVu (PV-DV402 only) is ON, Program AE and H.S.S. cannot be set in the menu. 2AUTO/MANUAL 4, 5 JOG KEY 3MENU 1POWER 1 2 3 4 5 6 Set POWER to CAMERA. Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor. Press MENU to display the menu screen.
Special Effect Features Audio/Video Fade In/Out You can make smoother scene transitions for a more professional look. 1, 3, AFADE Fade In Starting the first scene with “fade in” is very effective. 1 2 3 In REC/PAUSE mode, hold down FADE until the picture fades out. Press REC/PAUSE to start recording. Fade Out Use to create a soft ending or (together with fade in) for a soft transition from one scene to the next.
Special Effect Features Picture in Picture (PinP) You can display a PinP (still image) screen on the Main Picture. Note • PinP position is fixed at the bottom right of the screen. 1 2 3 Main Picture Picture in Picture (PinP still image) 4 PHOTOSHOT Set POWER to CAMERA. Press MENU to display the menu screen. Rotate JOG KEY repeatedly to select D.FUNCTION , then press JOG KEY to display the CAMERA FUNCTION menu screen. Press JOG KEY to select PinP . • Press MENU twice to exit this menu.
Special Effect Features Before you begin Photo Title You can use PhotoShot images stored on a Memory Card to record a WIPE or MIX effect on a cassette. Note When Photo Title is set to SET, the selected image and Title will appear before each recording is made. WIPE : The Photo title is replaced with the current scene in a wiping motion. • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to OFF before inserting a recorded Memory Card. (pp.
Advanced Settings White Balance Auto White Balance (“AWB”) automatically maintains optimum color balance in most lighting conditions. However, when using Digital Functions, etc., you may get better results by using the manual adjustment. 3, 4, A, B 1 2 3 JOG KEY 4 1POWER 2AUTO/MANUAL Set POWER to CAMERA. Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor. Press JOG KEY repeatedly until “AWB” appears in the EVF or LCD monitor.
Advanced Settings Auto Focus The Palmcorder automatically adjusts the focus over the entire zoom range. Manual Focus 4, 6POWER 1 2 3 4 5 ZOOM 5M.FOCUS DIAL 1POWER 6 2AUTO/ MANUAL Set POWER to CAMERA. Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor. Press FOCUS so that the “MF” (Manual Focus) indication appears in the EVF or the LCD monitor. Press and hold POWER ZOOM, “T” side (Telephoto), until the lens is at maximum zoom in.
Advanced Settings High Speed Shutter To record high speed motion (e.g. tennis stroke) with improved STILL or SLOW MOTION playback when watching the tape on this Palmcorder. Auto Shutter In the AUTO mode (no indication in the EVF and LCD monitor), the Palmcorder will automatically adjust the shutter speed (up to 1/350). • AUTO mode is automatically selected whenever the POWER Switch is set to CAMERA. Manual Selection 1 2 3, 4 JOG KEY 1POWER 2AUTO/MANUAL 3 4 Set POWER to CAMERA.
Advanced Settings Adjusting the Iris Manually Normally, the Palmcorder adjusts the exposure automatically. However, when the background is extremely bright, or when the subject is backlit, you can compensate by adjusting the iris manually. 1 2 JOG KEY 1POWER 2AUTO/MANUAL Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor. Press JOG KEY repeatedly so that Iris setting indication appears in the EVF or the LCD monitor.
Playback Your Recordings Playback using the LCD Monitor Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Insert a recorded cassette. You can also use the LCD monitor to playback your recording. 1 1POWER 2 3 4 5 180° 90° 90° 2LCD-OPEN 4PLAY Set the POWER to VCR. • The POWER lamp lights red. • Be sure POWER is fully turned to the VCR position. Press LCD-OPEN to unlock the LCD monitor and swing open. Press (REWIND/SEARCH) to rewind the tape. Press (PLAY) to start playback.
Playback Your Recordings Repeat Playback 1 1PLAY EVF/LCD R Adjusting the Volume 1, 2 2 1 VOLUME 2 Turn the Palmcorder OFF to exit the Repeat Playback mode. Rotate VOLUME to adjust the volume of the built-in speaker in PLAY mode. • The volume setting screen appears. Press “T” to increase the volume or press “W” to decrease the volume. EVF/LCD Blank Search You can go directly to a blank portion of tape and start recording exactly where you left off.
Special Effect Features Note • Sound is muted during all special effects. A During playback, hold down (FAST FORWARD/SEARCH) or Rapid Visual Search BPLAY B A, B A, B REWIND/ FAST FORWARD/ SEARCH SEARCH Note • When executing a rapid visual search, the picture may become bluish for an instant or mosaic. This is normal during this mode. EVF/LCD STILL Picture 1 2 1, 2PAUSE 2PLAY (REWIND/SEARCH). The search will continue for as long as the button is held down.
Special Effect Features Note • Sound is muted during all special effects. Slow Motion Playback (Remote Control Only) 1 Forward Slow: Press SLOW/F.ADV during play. Reverse Slow: SLOW/F.ADV during play. Press 2PLAY 1 1 2 Press PLAY to release. (During reverse slow motion playback, time SLOW/ F.ADV code indication may not change regularly.) SLOW/ F.ADV Note Variable Speed Search 2, 3 JOG KEY 1 2 3 Press (PLAY) to start playback. Press JOG KEY for about 1 second.
Special Effect Features Note • Sound is muted during all special effects. Frame by Frame Advance (Remote Control Only) 3PLAY 1 2 1PAUSE 2 2 3 SLOW/ F.ADV Press PAUSE during playback. Press SLOW/F.ADV to do a frame by frame advance. Press SLOW/F.ADV to do a frame by frame reverse. Press PLAY to release. Note • If you hold down SLOW/F.ADV, you can see a continuous series of still images at a slower speed than normal slow mode.
Special Effect Features Note • Sound is muted during all special effects. Jog Frame by Frame Search (Palmcorder Only) During Still mode, rotate JOG KEY to advance or reverse the picture one frame at a time. JOG KEY Index Forward/Reverse Search (Remote Control Only) Search for a particular scene by using the electronic index marks placed at the beginning of each recording.
Special Effect Features Strobe Multi Mode In Strobe Multi Mode, you can select the rate at which a succession of still screens are captured from the playback picture. 3, 4 JOG KEY 1POWER 1 2 3 4 Set POWER to VCR. Press MENU to display the menu screen. Rotate and press JOG KEY to select and set MULTI SETTING . Press JOG KEY repeatedly to set desired speed. Strobe Speeds Strobe Speeds 9 screen capture time 2MENU FAST Every 0.3 seconds NORM Every 0.6 seconds SLOW Every 1.
Special Effect Features View Recording/Playback on your TV [ TV with AUDIO/VIDEO IN Jacks ] Before you begin • When using S-VIDEO Connector, insert the DC Cable into the DC IN Terminal. (p. 15) 1 A/V OUT 2 Back of TV Audio In Video In 3 A/V Cable (Supplied) Set POWER to CAMERA or VCR. To view what the Palmcorder is recording or to playback a tape on your TV. Turn your TV ON and set it to LINE INPUT or S-VIDEO. Check your TV operating instructions for further information.
Digital Features Digital Zoom CAMERA mode This feature is useful when you want to record close-up shots of subjects located beyond a normal zoom range of 1X to 10X magnification. With the digital zooming feature, you can select a magnification of 25X, or even up to 700X. Note • Other Digital Functions are turned off automatically when the EIS and Digital Zoom are selected. 1 2 3 4 EVF/LCD Zoom In (“T”) D.ZOOM 5POWER Zoom Out (“W”) 5 ZOOM 3, 4 JOG KEY 1POWER 6 Set POWER to CAMERA.
Digital Features Digital Zoom (Continued) VCR mode 1 2 3 3, 4 JOG KEY 2MENU 1POWER 5PLAY 4 5 6 Set POWER to VCR. Press MENU to display the VCR MENU screen. Rotate JOG KEY to select PLAY FUNCTION , then press JOG KEY to display the VCR PLAY FUNCTION menu screen. Rotate JOG KEY to select D.ZOOM , then press JOG KEY to select ON. • Press MENU twice to exit. Press (PLAY) to start playback. • The center portion of the image doubles in size. Repeat steps 2~4 to select OFF to cancel this feature.
Digital Features Dual Digital Electronic Image Stabilization System (D.E.I.S.) This feature helps compensate for any unintentional hand or body movement. It can be used in both the Recording and Playback (VCR) modes. CAMERA mode 1 2 Set POWER to CAMERA. Press EIS to stabilize the picture. • Picture flicker may be observed when taping under fluorescent lighting conditions. • The EIS indicator flashes when the light level is inadequate. • Turn D.E.I.S. OFF during recording when using a tripod.
Digital Features Other Digital Functions Use the following features to add interest and professionalism to your recordings or playback. Select from twelve special effects. 3, 4, 5 JOG KEY 1 2 3 2MENU 1POWER 4 Types of Digital Functions 5 Press MENU to display the menu screen. Rotate JOG KEY to select D.FUNCTION in the CAMERA mode menu screen or PLAY FUNCTION in the VCR mode menu screen, then press JOG KEY to display the CAMERA FUNCTION or VCR PLAY FUNCTION menu screen. Rotate JOG KEY to select D.
Editing Features Audio Dubbing using the External (PV-DV402 only) or Built-in Microphone Before you begin • Connect the external Microphone (if used) (PV-DV402 only). • Turn on the Palmcorder. • Insert a pre-recorded tape to be dubbed. The original sound can be replaced with new sound using the built-in Palmcorder The AUDIO-REC setting in CAMERA microphone or an external microphone MENU mode should be as follows: (PV-DV402 only).
Editing Features 4, 5PAUSE To listen to the desired audio sound, set the AUDIO setting of the VCR mode MENU (Menu OSD: p. 103) as follows: AUDIO:The following selections are available for 12 bit AUDIO dubbed recordings only (sound recorded in SP mode only). Set this position to listen to the ST 1 original sound. Set this position to listen to the ST 2 audio dubbed sound. Set this position to listen to both MIX the original sound and the audio dubbed sound.
Editing Features Copying your Tapes to S-VHS or VHS Cassette Source (Playing) Palmcorder DC Cable (Supplied) S-VIDEO OUT A/V OUT Before you begin • Connect both Palmcorder and VCR to their power sources. • Connect the Palmcorder to a VCR as illustrated left. • Turn ON both units. • Set the recording VCR’s Input Signal Selector to LINE. • Set the Palmcorder POWER to VCR. • Before using S-VIDEO Connector, insert the DC Cable into the DC IN Terminal. (p.
Editing Features Copying from Digital Equipment (dubbing) Before you begin High quality digital-to-digital copying can be accomplished if both Palmcorders incorporate the DV Input/Output (i.LINK) Connector (DV Interface cable (i.LINK) is not supplied). Source (Playing) Palmcorder DV Input/Output (i.LINK) Connector Recording Palmcorder • Connect both Palmcorders to their power sources. • Connect the two Palmcorders using the DV Interface cable (i.LINK) (4-pin to 4-pin). • Turn both Palmcorders ON.
Card Features Before you begin Card PhotoShot You can record still images to a Memory Card. Warning • Memory Card will not work when DV Interface Cable (i.LINK) is connected. PHOTOSHOT 3 2JOG KEY • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to OFF before inserting a Memory Card. (p. 13) 1 1POWER M-CARD Lock 2 2MENU Slide the M-CARD Lock Switch to unlock, then set POWER to M-CARD. • The POWER lamp lights red. • Be sure POWER is fully turned to M-CARD position.
Card Features Cautions for the Memory Card • While Memory Card data is being read, do not remove it, turn off the power, or subject unit to vibrations and/or shocks. • Do not leave the Memory Card in a place with high temperature, a place exposed to direct sunlight, or a place where electromagnetic waves and static electricity can be generated. • Electromagnetic waves, static electricity, malfunction of the Digital Video Palmcorder or of the Memory Card itself could erase the data recorded on it.
Card Features Playback Still Images You can view the images on the Memory Card. Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) 1 3, 4 JOG KEY Slide the M-CARD Lock Switch to unlock, then set POWER to M-CARD. • “PLAY: PUSH PLAY KEY” is displayed for 10 seconds. 1POWER M-CARD Lock 2M-PLAY 2 Press (M-PLAY) to display the Multi playback screen. • “PLEASE WAIT” appears on-screen.
Card Features Before you begin Delete Specific Images You can delete unwanted images and increase the remaining image memory. Warning: Once deleted, images cannot be restored. DELETE PAGE Delete specific images from a page. DELETE ALL Delete all images. (p. 52) • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) 1 2 FORMAT Delete all data. (p. 53) 3 3, 4, 5 JOG KEY Slide the M-CARD Lock Switch to unlock, then set POWER to M-CARD.
Card Features Delete All Image Pages You can delete all images from the Memory Card easily with this operation. Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) Warning: Once deleted, images cannot be restored. 2, 3 1 2 JOG KEY 2M-DEL Do steps 1 and 2 on page 51. Press (M-DEL) to display the DELETE menu. Then, rotate and press JOG KEY to select ALL . • The screen below is displayed. • To cancel delete, press (M-STOP) or rotate and press JOG KEY to select NO.
Card Features Format the Memory Card You can easily format your Memory Card using this operation. Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) Warning: Formatting permanently removes all image data. 2, 3 1 2 JOG KEY 2M-DEL Do steps 1 and 2 on page 51. Press (M-DEL) to display the DELETE menu, then rotate and press JOG KEY to select FORMAT . • The screen below is displayed. • To cancel format, press (M-STOP) or rotate and press JOG KEY to select NO.
Card Features Before you begin DPOF Setting You can select the images to be printed, the number of prints, and other print-related information (DPOF setting) on a Memory Card. “DPOF” stands for Digital Print Order Format, and since printing data can be added to images on the Memory Card, the Memory Card can be used with any system that provides DPOF. VARIABLE: You can select images recorded on the Memory Card and set the number of prints desired.
Transferring Your Images (Windows) You can transfer images from your Palmcorder tape to your PC (Personal Computer).
Transferring Your Images (Windows) Software Installation (Windows 95 (for ArcSoft Software only)/ 98SE/Me/2000/XP) Caution • Please install Palmcorder USB Device Driver first before connecting the Palmcorder and your PC using USB Cable. Once Palmcorder USB Device Driver is installed, you must restart your computer for installation to take effect.
Transferring Your Images (Windows) Notes on PHOTOVU/MPEG4 Movie Messenger System operation • For PHOTOVU/MPEG4 Movie Messenger System, do not connect the i.LINK and USB terminals to the Palmcorder at the same time. • Make sure Palmcorder power is not shut off during use as your PC system may become unstable. Therefore, the AC Adaptor should be used as the power source. (Be especially careful when recording in M-CARD or CAMERA mode as the power eventually shuts off automatically if a tape is inserted.
Transferring Your Images (Windows) Palmcorder USB Device Driver/SD Drive, Palmcorder File Converter (M-CARD Mode) [ This screen is an example (Windows 2000) ] 1 2 Click “Start,” “Settings,” and “Control Panel.” Double-click on “System”, verify [USB Storage Device Controller]* is displayed in [Universal Serial Bus controllers] of [Device Manager]. * If you are using Windows 98SE, [MATSUSHITA USB Storage Device Controller] will be displayed.
PHOTOVU/MPEG4 Movie Messenger System Connection (for PHOTOVU/MPEG4 Movie Messenger System) 2 USB Terminal USB Terminal 3 1 Turn on your PC. 2 Set the Palmcorder POWER to VCR. USB Cable (supplied) For Windows XP users 3 1 2 3 Note • For extended use, the AC Adaptor should be used as a power source. 59 DV202_402PN.p 55-60.p65 59 02/02/13, 17:53 PC Connection Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CAPTURE” appears in the EVF or the LCD monitor.
PHOTOVU/MPEG4 Movie Messenger System For Windows 2000 users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CAPTURE” appears in the EVF or the LCD monitor. • The “Found New Hardware” screen of Windows is displayed. • When the Palmcorder and PC (with Windows 2000) are connected via USB, a message, such as the one below, is displayed. The following message is displayed. However, testing by the manufacturer has confirmed functionality of this palmcorder with Windows XP/2000.
PHOTOVU/MPEG4 Movie Messenger System Running the PHOTOVU/ MPGE4 Movie Messenger System* * PHOTOVU: You can transfer Still images from your Palmcorder tape to a PC. MPEG4 Movie Messenger System: You can transfer Motion images from your Palmcorder tape to a PC. Before you begin • Insert a recorded tape. (p. 11) 1 2 3 4 Set Palmcorder POWER to VCR. Connect the Palmcorder to your PC using the USB Cable (supplied) or DV Interface Cable (i.LINK) (not supplied). (pp.
PHOTOVU/MPEG4 Movie Messenger System Using Tape Image Data (USB) By connecting the Palmcorder and PC with the USB Cable, you can transfer Motion images and Still images saved on the DV Tape directly to your PC. Note • Detail mode cannot be used with a USB connection. • Deactivate your PC ScreenSaver or this application may shutdown during image capture. Before you begin • Insert a recorded tape. (p. 11) • Make Palmcorder-PC connections. (pp. 59, 60) • Turn your PC on. (p.
PHOTOVU/MPEG4 Movie Messenger System Playing back the saved Motion and Still images You can play back the saved Motion images and Still images (p. 62) for confirmation. 1 2 Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users 2VideoGift 3 • If “Unable To Locate DLL” warning indication is displayed, please see page 90.
PHOTOVU/MPEG4 Movie Messenger System VideoGift Screen You can use these features using the VideoGift Screen. 14 1 9 2 10 3 11 4 12 5 15 16 13 6 7 8 17 1 Slider 10 Settings 2 11 3 4 5 6 7 8 9 Drag the pointer of the playback start position. Movie Mode You can display motion images. Open Movie You can open folders containing video files (*.AVI, *.WMV). Open Audio You can open folders containing audio files (*.WAV). Valid only when the file is opened in the VideoGift screen.
PHOTOVU/MPEG4 Movie Messenger System Using the VideoGift Screen 1 2 Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users 2 VideoGift 3 • If “Unable To Locate DLL” warning indication is displayed, please see page 90. Click [View Manager] to display the View Manager screen.
PHOTOVU/MPEG4 Movie Messenger System Setting the Mail Software It is possible to set the mail software to start up automatically when [E-Mail] of VideoGift is clicked. Note The e-mail Software must support MAPI (Messaging Application Programming Interface). Below are some e-mail Software programs which support MAPI: Microsoft Outlook, Microsoft Outlook Express, Netscape Messenger: • Outlook Express 5x, Outlook97, Outlook98, Outlook2000 • Outlook Express 4x • Other MAPI applications [Netscape Messenger 4.
PHOTOVU/MPEG4 Movie Messenger System Attaching captured Motion and Still images to your e-mail You can easily transfer and compress your Motion images as attachments to your e-mail. Before you begin • Insert a recorded tape. (p. 11) • Make Palmcorder-PC connections. (pp. 59, 60) • Turn your PC on. (p. 59) • Set Palmcorder POWER to VCR. 1 2 2VideoGift Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System. Click [VideoGift] to display the VideoGift screen.
PHOTOVU/MPEG4 Movie Messenger System Sending a Portion of a Motion Image 1 2 Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users 1 2 7E-Mail 6Preview 7Uploader 3 4 5 6 7 Slide-Show Edit A collection of still images can be edited as slides. 1 2 • If “Unable To Locate DLL” warning indication is displayed, please see page 90.
PHOTOVU/MPEG4 Movie Messenger System Setting the Size and Quality of Motion and Still Image 5 1 2 5 Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users • If “Unable To Locate DLL” warning indication is displayed, please see page 90.
PHOTOVU/MPEG4 Movie Messenger System Selecting a Frame from a Motion Image 1 This screen is displayed when an individual frame from a moving image file is to be added as a still image. 2 Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users • If “Unable To Locate DLL” warning indication is displayed, please see page 90.
PHOTOVU/MPEG4 Movie Messenger System Uploading the image to PictureStage Home Page* You can upload edited moving images and still images to the PictureStage Home Page. Before you begin • Attain internet access. • Before using this feature, you must become a registered member of PictureStage. For details on installation, settings, etc., please visit http://www.picturestage.com/ (current as of Dec. 28, 2001). 1 2 Repeat steps 1~4 on page 61 to run the PHOTOVU/MPEG4 Movie Messenger System.
PHOTOVU/MPEG4 Movie Messenger System 5 6 7 Click [Upload To Photo Album] to upload the Still Image or [Upload To Video Album] to upload the Motion Image. • The “PictureStage Image (Video) Uploader” screen is displayed. • Click [Exit] to exit uploader. Enter your login ID and password, and then click [Continue]. • Click [Free Sign up] if you have no login ID. The PictureStage Home Page opens and there you can get a login ID and password.
Transferring Your Images (i.LINK) (Windows) PC Connection with DV Interface Cable (i.LINK) A video clip can be transferred directly to your PC (Personal Computer) via a DV Interface Cable (i.LINK) (not supplied) using products and software from a number of video editing software companies. Using products from video editing software companies allows you to capture and edit video clips using the DV Interface (i.LINK).
PHOTOVU/MPEG4 Movie Messenger System (i.LINK) Before you begin Using Tape Image Data By connecting the Palmcorder and PC with the DV Interface Cable (i.LINK), you can transfer Motion images and still images saved on the DV Tape directly to your PC. Note • If PHOTOVU/MPEG4 Movie Messenger System does not work, please refer to note on page 73. • Deactivate your PC ScreenSaver or this application may shutdown during image capture. • Insert a recorded Tape. (p. 11) • Make Palmcorder-PC connections. (p.
PHOTOVU/MPEG4 Movie Messenger System (i.LINK) 3Normal 3, 3Detail 4Movie Capture 4Still Capture DV 6STOP [When selecting Detail] Note • Detail mode lets you specify the start and end frames for the video segment you want to capture and save. 3 4 5 5, 7, 5Select 6 To capture Still images [When selecting Detail] 3 4 5 Click on [Movie Capture] at the point you wish to capture a Motion image. • The screen to select the start frame is displayed.
Palmcorder USB Device Driver/SD Drive Connection (for Palmcorder USB Device Driver/SD Drive) 2 USB Terminal USB Terminal 3 1 2 USB Cable (supplied) Turn on your PC. Set the Palmcorder POWER to M-CARD. For Windows XP users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CONNECT WITH PC” appears in the EVF or the LCD monitor. • The “Found New Hardware Wizard” screen of Windows is displayed. The following message 2 is displayed.
Palmcorder USB Device Driver/SD Drive For Windows 2000 users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CONNECT WITH PC” appears in the EVF or the LCD monitor. • The “Found New Hardware” screen of Windows is displayed. • When the Palmcorder and PC (with Windows 2000) are connected via USB, a message, such as the one below, is displayed. The following message is displayed.
Palmcorder USB Device Driver/SD Drive Using Memory Card Image Data By connecting the Palmcorder and PC with the USB, you can transfer Still images saved on the Memory Card directly to your PC. Before you begin • Install the Palmcorder USB Device Driver. (p. 56) • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) • Make Palmcorder-PC connections. (pp. 76, 77) • Turn your PC on. (p.
Palmcorder File Converter Using Palmcorder File Converter You can convert the JPEG data of your PC into DCF (Design rule for Camera File System) data, and transfer this data to your Palmcorder via USB. 1 2 3 4 Set Palmcorder POWER to M-CARD. Connect the Palmcorder to your PC using the USB Cable (supplied). (pp. 76, 77) Click on “Start,” “(All) Programs,” “Panasonic,” “Palmcorder,” then “File Converter 3.0.” Select and click “To resize the image” or “To convert format for Panasonic Digital Palmcorder.
Palmcorder File Converter 6 7 Select the folder to which the converted file is to be saved. • The Conversion results screen is displayed. Use “Help” for detailed instructions. When selecting “To convert format for Panasonic Digital Palmcorder” 5 6 7 Select the file to be converted. Select the drive to which the converted file is to be saved. • The Conversion results screen is displayed. Use “Help” for detailed instructions. 80 DV202_402PN.p 79-80.
Web Camera Before Using Web Camera* Features Web Camera* MSN Messenger and NetMeeting are software that can be linked and used together. Using the Palmcorder and the Internet, you can communicate with others by having picture and sound similar in fashion to a videophone. Please read this first • To use the Web Camera feature, Microsoft’s Windows Messenger, MSN Messenger Service, and Windows NetMeeting are required. • For this feature, both parties must have Windows XP.
Web Camera Connection (for Web Camera) Lch (White) AV OUT A/V Cable (supplied) To MIC Terminal Audio Adaptor (supplied) USB Terminal 1 USB Terminal 1 2 USB Cable (supplied) Turn on your PC. Set the Palmcorder POWER to CAMERA. For Windows XP users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “Found New Hardware Wizard” is displayed. The following message 2 is displayed.
Web Camera For Windows 2000 users 3 4 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “Found New Hardware” is displayed. • “CONNECT WITH PC” and “WEB CAM” are displayed in the EVF and LCD monitor. A gray box is also displayed. The image within the box can be used with communication. • Place the Palmcorder so that you are in the picture. • To confirm if the connection between the Palmcorder and PC is correct, please refer to “Audio Tuning Wizard” on page 85.
Web Camera (For Windows XP users) For Windows Messenger (Windows XP only) When Windows Messenger is newly installed or when running for the first time, the following settings become necessary. For more details, please read the corresponding Help file. Note • Once settings are performed, they are not required from the second time the software is run. Before you begin • Be sure you have a dial-up connection. • Referring to pages 82~83, connect the Palmcorder and PC.
Web Camera (For Windows XP users) 5 Type in your E-mail address and password. • You’ll need to get a hotmail address. If you do not have one, click on [Get a .NET Passport]. Please carefully read the displayed contents and then proceed. There are times when a Version Upgrade screen will be displayed. However, if you are using Windows Messenger 4.5 or later, there is no need to upgrade. 6 Click on [Audio Tuning Wizard] in the [Tools] menu. Note • You can set the volume for playback or mic volume, etc.
Web Camera (For Windows XP users) 8 The person calling (inviting) side Double-click a person to call from those currently [on-line]. • “xxxx-conversation” screen is displayed. 9 The person calling (inviting) side Click [Start Camera] in the “xxx-conversation” screen. • A message inviting the other person is displayed. The invited person side A message asking if the person accepts or declines is displayed. Click [Accept] on the screen. • To ignore the invitation, click [Decline].
Web Camera (For Windows 98SE/Me/2000 users) For MSN Messenger Service and Windows NetMeeting (Windows 98SE/Me/2000) When MSN Messenger Service is newly installed or when run the first time, the following settings become necessary. For more details, please read the respective Help file. Note • Once settings are performed, they are not required from the second time the software is run. Before you begin • Be sure you have a dial-up connection. • Referring to pages 82~83, connect the Palmcorder and PC.
Web Camera (For Windows 98SE/Me/2000 users) 6 Click on [Audio Tuning Wizard] in the [Tools] menu. Note • You can set the volume for playback or mic volume, etc. • Also, confirm that the Palmcorder and PC are connected correctly. The person you wish to access needs to do settings 1~6 also. 7 Select [Tools] -> [Add a Contact] to register the person you wish to access in MSN Messenger Service. • Please enter the same e-mail address that the other person has registered with MSN Messenger Service.
Web Camera (For Windows 98SE/Me/2000 users) 9 The person calling (inviting) side Click [Start NetMeeting] in the “xxx-conversation” screen. The invited person side The Instant Message screen appears and a confirmation message is displayed. Click on [Accept]. The NetMeeting screen is automatically opened. Note 10 11 13 Click on [Options] in the [Tools] menu to confirm Video Camera Properties.
Warning Indications Windows 2000 In Windows 2000, startup PHOTOVU/ MPEG4 Movie Messenger System. Clicking on [VideoGift] may cause the type of error to occur to the left. If so, please perform the following instructions. Download and install Media Player (7.1 or later), go to http://www.microsoft.com/windows/ mediaplayer (current as of Dec. 28, 2001). • “Windows Media. com: Download” is opened. Click [Download Now!] on the screen. • The “File Download” screen is displayed.
Transferring Your Images (Macintosh) You can transfer images from your Palmcorder tape to your Macintosh. System Requirements (for Built-in SD Drive/ArcSoft Software) • USB Port • Mouse or other pointing device • 210 MB minimum available hard disk space (for ArcSoft Software) • High color (16 bit) or more (for ArcSoft Software) • Mac OS 9.0~9.1 • Mac OS 8.6~9.
Transferring Your Images (Macintosh) Using Built-in SD Drive Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) 1 2 3 4 Set the Palmcorder POWER to M-CARD. Connect the Palmcorder to your Macintosh using the USB Cable (supplied). (p. 91) • “PLEASE WAIT”, “CONNECT WITH PC”, and “STORAGE” is displayed on the LCD monitor. Double click the “Untitled” icon. • You can view images stored on the Memory Card and also save them to your hard disk.
Palmcorder Accessory System Accessory # Figure Description AC Adaptor with AC Cable and DC Cable CGR-D08A/1B 800mAH / 1 h 30 min, Battery Pack CGR-D16A/1B 1 600mAH / 3 h, Battery Pack CGP-D28A/1B 2 800mAH / 5 h, Battery Pack CGR-D53A/1K 5 300mAH / 9 h, Battery Pack PV-DDC9 DV Interface Cable (i.
Notes On Operations Before you begin Replacing the Bulb 1 • Set POWER to OFF. Insert a rigid wire, such as an extended paper clip into point (A) and lift cover up. 3 Replace bulb using a clean cloth or tissue. (Do not touch with fingers.) (A) 4 2 Replace lens cover. Using Tweezers or needle-nose pliers, carefully remove bulb. • Take unit to servicenter if you need assistance. Note • Handle bulb gently. Excessive force may cause bulb to crack. DANGER: Use only replacement bulb (PART NO.
Notes On Operations Approximate Brightness Values Your Palmcorder has been designed for normal scene illumination of 150 footcandles (1500 lx). However, the Palmcorder may be used at F1:1.8, if illumination is more than 0.5 footcandles (5 lx). The table below shows the color temperature for reference.
Specifications Power Source: Palmcorder: 7.2 V DC (Battery) 7.8 V DC (AC Adaptor) AC Adaptor: 110/120/220/240 V AC, 50/60 Hz Battery: Lithium-Ion Type DC 7.2 V Power Consumption: Palmcorder : 7.2 V/7.8 V DC 6.5 W (Max. 9.5 W) AC Adaptor : 18 W 1 W (when not in use.) Digital Interface USB/i.
Before Requesting Service Cleaning Care for Video Heads Clogged Video Head (a) Video Head Cleaning: Normally, your Palmcorder will not require head cleaning. However, it is possible that the heads may become clogged due to dust in the air, playing damaged tapes, long term use, etc. If “NEED HEAD CLEANING” appears for 5 seconds in the EVF or LCD monitor, the heads may require cleaning. (b) Cleaning the Heads: It is recommended that head cleaning be performed by a qualified service technician.
Before Requesting Service If you have a problem with your Palmcorder, it may be something you can correct yourself. Check the list below for symptoms and corrections. Symptom Correction No picture in the EVF or LCD Monitor... • Make sure the Power Source is connected. (pp. 14, 15) • Make sure the POWER switch is set to VCR or CAMERA. (pp. 18, 32) • Check the Dew Indicator. (p. 99) • Make sure the Battery is fully charged. (p. 14) • Make sure all necessary cables are connected correctly and firmly. (p.
On-Screen Displays (OSD) The following warning displays appear in the EVF and the LCD monitor. Indications Condition If the Palmcorder is in CAMERA mode without a cassette inserted, “ ” will flash and “TAPE NOT INSERTED” will appear for 5 seconds. Recording will not start. If the Palmcorder is in CAMERA mode or Audio dub mode with the cassette sliding record tab opened, “ ” will flash and “CHECK REC TAB” will appear for 5 seconds. Recording will not start.
On-Screen Displays (OSD) Indications Condition If you play a tape recorded in a format other than NTSC or you try to copy copy-protected data, “INCOMPATIBLE DATA” will appear. When a still image is transferred from a tape to an already full Memory Card, or when setting is DPOF, “NO SPACE LEFT” appears. If the Palmcorder is in M-CARD mode or Photo Title (CAMERA mode) and the DV Interface Cable (i.LINK) is connected, “DISCONNECT DV CABLE” appears. In this case, remove the DV Interface Cable (i.
MENU OSD Camera Mode Menu Screen 4 1 5 2 3 6 4 5 7 6 7 8 8 9 10 11 12 1 3 D.FUNCTION (pp. 41, 43) To select one of the 10 digital functions. Setting to OFF cancels the previously selected digital function. D.ZOOM (p. 40) To select D.ZOOM1 (from 10X to 25X) or D.ZOOM2 (from 10X to 700X). Setting to OFF cancels the previously selected digital zoom. PROGRESSIVE (p. 20) When set to ON, still pictures taken with PhotoShot are recorded with a higher resolution than with normal PhotoShot.
MENU OSD 13 13 14 15 14 16 17 18 19 15 20 16 17 18 21 19 22 20 21 22 REMOTE (p. 10)ly VCR1: To receive signals from the Remote Control, set to VCR1. VCR2: To receive signals from the Remote Control, set to VCR2. OFF: To prevent reception of signals from the Remote Control. BEEP Set to ON to hear beep when starting and stopping camera recording or when unusual conditions occur. To cancel the beep, set to OFF.
MENU OSD VCR Mode Menu Screen 4 1 2 3 5 4 6 5 7 6 7 8 9 8 10 1 3 9 10 103 DV202_402PN.p103-104.p65 103 02/02/13, 17:55 For Your Information 2 D.FUNCTION (p. 43) To select one of the 6 digital functions. Setting to OFF cancels the previously selected digital function. D.EFFECT (p. 43) To select one of the 2 digital picture effects for playback. Setting to OFF cancels the previously selected digital effect. D.ZOOM (p. 41) Set to ON to double the size of a playback image.
MENU OSD 11 11 12 12 13 14 13 15 14 15 DISPLAY (p. 106) To select the desired type of display and counter indication displayed on the LCD Monitor or in the viewfinder. C.RESET (p. 106) Setting to ON resets the counter to zero. DATE/TIME (p. 105) The date and time can be set and displayed on the screen. CLOCK-SET (p. 16) When set to ON, the date and time can be set on the screen. LCD/EVF SETTING (p.
Electronic Viewfinder/LCD Monitor Indications Here are some of the basic indications which will appear on the Palmcorder EVF and LCD Monitor. Only Date and Time indications will be recorded onto the tape. CAMERA/VCR Mode h a i j b c d e f g a g Battery Remaining FULL EMPTY b Tape Remaining (AY-DVM30EA) Date and Time Indication (Menu OSD: pp. 102, 104) As shown below, the date and time indication changes each time DATE/TIME is selected from the Palmcorder’s MENU (Menu OSD: pp.
Electronic Viewfinder/LCD Monitor Indications CAMERA/VCR Mode k l m IMPORTANT NOTE: • Display must be set to ON for MF, AE, W.BALANCE or BACK LIGHT indications to be displayed on the EVF or LCD Panel selected. l Display ON/OFF and Counter/Time Code • when C.RESET does not work when DISPLAY The indication switches as shown is set to OFF and T.CODE. below when the desired “DISPLAY” mode is selected from the menu. m Tape Mode Indications (Menu OSD: pp. 102, 104) REC Recording.
Electronic Viewfinder/LCD Monitor Indications CAMERA/VCR Mode n o p q s t r u v w x y n Zoom Magnification Level (p. 40) v o Digital EIS Indications (p. 42) This display appears when EIS is pressed. Z.MIC Indication (Menu OSD: p. 101) This display appears when ZOOMMIC is set to ON. w Backlight Indication (p. 23) This display appears when BACK LIGHT is pressed. Light Indication (p. 9) This display appears when LIGHT is set to ON. x WIND-CUT Indication (Menu OSD: p.
Electronic Viewfinder/LCD Monitor Indications PHOTO Mode [ Photo Rec Mode ] [ Photo Play Mode ] c a b d e f g h [ Photo Play Mode ] a b Image Page Remaining Indication (p. 48) • Image pages left in selected mode. “000” flashes when memory is full. • Memory capacity provided all pictures are taken in the same mode: “NORMAL” mode Approx. 70 images (Supplied 8 MB Memory Card) “FINE” mode Approx. 30 images (Supplied 8 MB Memory Card) REC MODE • NORMAL or FINE mode.
Index of Controls Front View Built-in Twin Capsule 2-Way Microphone System MAGICVU/0LUX (PV-DV402 only) p. 25. Shoulder Strap Attachment Ring p. 8. Lens BATT RELEASE pp. 14, 15. Remote Sensor p. 9. Built-in Light pp. 9, 94. M-CARD Door p. 13. Side View JOG KEY pp. 16, 17. M.FOCUS DIAL p. 29. External Microphone Jack (PV-DV402 only) p. 44. M-CARD EJECT p. 13. Built-in Speaker p. 33. Shoulder Strap Attachment Ring p. 8. Hand Strap p. 8. POWER (VCR•OFF• CAMERA•M-CARD) pp. 11, 12, 13. M-CARD Lock p.
Index of Controls Rear View PHOTOSHOT pp. 20, 48, 49. Electronic Viewfinder (EVF) p. 12. POWER ZOOM pp. 21, 40. VOLUME p. 33. MENU pp. 16, 17. A/V Output Connector pp. 39, 82. PHONE p. 32. Lens Cap p. 8. Top View PAUSE pp. 34, 45, 47. CAMERA STILL p. 26. M-DEL pp. 51, 52, 53. FOCUS p. 29. AUTO/MANUAL pp. 28~31. PLAY pp. 12, 32. M-PLAY pp. 50, 51. MULTI p. 38. FADE p. 25. REC p. 47. LIGHT p. 9. STOP pp. 12, 32. M-STOP pp. 50~53. EIS p. 42. REW pp. 12, 32. RECORDING CHECK p. 22. FF p. 34.
Index of Controls AC Adaptor AC Power Cord pp. 14, 15. POWER Lamp pp. 14, 15. CHARGE Lamp p. 14. VCR DC Output Connector p. 15. CAUTION: This unit will operate on 110/120/ 220/240 V AC. An AC plug adaptor may be required for voltages other than 120V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug. We recommend using the accessory power plug adaptor (VJSS0070) in an area which has special AC outlets. Remote Control DATE/TIME pp.
Index A F Q About the Memory Card .. 94 AC Adaptor ...... 6, 14, 15, 93 Accessories (Optional) .... 93 Accessories (Supplied) ...... 6 A/V Cable .............. 6, 39, 82 Audio Adaptor .............. 6, 82 Audio Dubbing ............ 44, 45 Audio/Video Fade In/Out . 25 Fast Forward/Rewind Check ... 34 Focus ............................... 29 Format the Memory Card .... 53 Frame by Frame Advance ... 36 Quick Guide ......... 11, 12, 13 B I Backlight .......................... 23 Battery Pack ....
