PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 3 OPERATION GUIDE R Digital Video Camcorder Operating Instructions Models No. PV-DV202 PV-DV402 [ PV-DV402 shown ] Mini Before attempting to connect, operate or adjust this product, please read these instructions thoroughly. Spanish Quick Use Guide is included. Guía para rápida consulta en español está incluida. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information below. The serial number is on the tag located on the underside of your Palmcorder. Be sure to retain this manual as your convenient Palmcorder information source.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Important Safeguards 11. Grounding or Polarization — This video unit may be equipped with either a polarized 2-wire AC (Alternating Current) line plug (a plug having one blade wider than the other) or 3-wire grounding type plug, a plug having a third (grounding) pin. The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Important Safeguards 15. Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Table of Contents Before Use Things You Should Know ................................................................................................ 2 Important Safeguards ..................................................................................................... 3 Precautions ..................................................................................................................... 4 Before Using ....................................
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Using This Operating Instructions book is designed for use with models PV-DV202 and PV-DV402. The PV-DV402 is the model used for illustrative purposes. Features may vary, so please read carefully. Differences between models Model Number LCD Monitor PV-DV202 PV-DV402 63.5 mm (2.5 inch) Liquid Crystal Display MagicVu™ IR Filter (0Lux) MIC IN EXTERNAL 88.9 mm (3.5 inch) Liquid Crystal Display NO YES NO YES Unpack your Palmcorder 1 pc.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Using Record Speed/Playback Time Cassette type Record Speed/ Playback time LP SP AY-DVM30EA 30 minutes 45 minutes AY-DVM60EA 60 minutes 90 minutes AY-DVM80EA 80 minutes 120 minutes Erase Protection Cassettes have a sliding record tab to ensure recordings are not accidentally erased. 1 To prevent accidental erasure: Slide the tab to the left (open). record tab 2 To record again: Slide the tab to the right (close).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Using Attaching the Shoulder Strap 1 2 Adjust the Length 1 2 Undo the two strap ends from their buckles. Thread the strap ends through the Strap Attachment Rings. Loosen the strap from the Buckle and create a loop. Pull the strap firmly through the Buckle to shorten or lengthen the strap. 1 OR 3 Reinsert the strap ends through their buckles. • Make sure the straps are not twisted.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Using Using the Built-in Light Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to CAMERA or M-CARD. 1 Before Use To brighten the natural colors in a scene. Hold down LIGHT for more than 0.7 seconds to turn ON or OFF. • “ ” will appear on the screen. Built-in Light Note • Using Light reduces battery time. • Provide adequate ventilation if using Light in a hot environment for a long time.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Using Replace the Battery B 1 While pressing the tab in the direction of the arrow (A) with your fingernail, pull out the Battery Tray (B). A + 2 3 Insert the battery into the Battery Tray with the facing up. Do not reverse the polarity. + mark Insert the Battery Tray. Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may present a risk of fire or explosion. Caution: battery may explode if mistreated.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Quick Guide Before you begin Insert the Battery Pack Before Use • Charge the Battery. (p. 14) Protection Film Note 2 • Remove the Protection Film before use. 1 1 Insert the Battery Pack and slide it up until it locks with a click. Insert Cassette These Palmcorders are equipped with the Easy Cassette Eject System so it is easy to insert or remove tapes, even when on a tripod. (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Quick Guide Camera Recording When the LCD monitor is fully open, the Viewfinder automatically turns OFF. 1 2 Set POWER to CAMERA. Adjust the Vision Adjustment Control to your eyesight. Viewfinder 180° 90° 4 Press REC/PAUSE to start recording. Press REC/PAUSE again to pause recording. To Watch Playback in the LCD (Liquid Crystal Display) When the LCD monitor is fully open, the Viewfinder automatically turns OFF.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Quick Guide Before you begin Insert Memory Card* Before Use • Charge the Battery. (p. 14) *Memory Card: MultiMediaCard or SD Memory Card (p. 94) • Be sure to insert the Memory Card before using the Card PhotoShot. (p. 48) Below is a list of memory cards which can be used in this Palmcorder. Memory Card Capacity SD Memory Card (RP-SD008BMKO) (supplied) 8 MB MultiMediaCard (SanDisk brand) 8 MB, 16 MB SD Memory Card (optional) (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Supplying Power Charge the Battery Pack on the AC Adaptor 1 2 POWER Lamp 3 CHARGE Lamp Connect and plug in the Power Cord as shown. • POWER Lamp will light. • Remove the DC Cable, if attached, from the adaptor. Attach the Battery as shown to charge. • CHARGE Lamp lights up. It goes out when charging is complete (approx. 1 hour). Expect approx. 1 hour 30 minutes of operation (EVF usage) when fully charged. Remove the Battery.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Supplying Power Battery Care To avoid damage to the Battery: • Charge only with specified charger. • Charge the Battery within an ambient temperature range of 10 °C (50 °F) and 30 °C (86 °F). • The Battery may be warm after charging or just after use. This is normal. • Do not use an insufficiently charged or worn out Battery. • If charging is done in extreme low or high temperatures, Battery charge time increases. • Do not drop or jar the Battery.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Setting the Clock Set the Date and Time The date and time is calculated, including leap year, up to DEC 31 2089. Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to CAMERA or VCR. 1 Press MENU to display the Camera or VCR mode menu screen. (p. 17) [ CAMERA MENU ] [ VCR MENU ] 2, 3, 4 JOG KEY 1MENU .
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Using the Palmcorder Menu Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to CAMERA or VCR. 2, A, B, C Displaying the MENU 1 2 Press MENU to display the CAMERA or VCR menu (according to the POWER setting). Rotate JOG KEY to select a menu item. Setting the MENU Items (EX. VCR Mode menu) A B Press JOG KEY to set your selection. Rotate JOG KEY to select a menu item. JOG KEY 1, D MENU CAMERA Main menu 1 : D.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Camera Recording Simple Recording Remove the lens cap and clip it to the hand strap. Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Insert a cassette with the record tab closed. (p. 7) 1 2 Clip here EVF REC/PAUSE mode POWER Lamp 3 4 1, 5 POWER 2Vision Adjustment Control 3MENU 5 Set POWER to CAMERA. • The POWER Lamp lights red. • Be sure POWER is fully turned to the CAMERA position.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Camera Recording Using the LCD Monitor The LCD (Liquid Crystal Display) monitor can be used while recording. 1 2 1LCD-OPEN 90° 90° Swing the LCD monitor fully open and adjust the viewing angle. • The LCD monitor will automatically turn on. • When the LCD monitor is completely closed, it will shut off automatically to save power. • Adjust the LCD Brightness and/or color of the LCD monitor if necessary.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Camera Recording Digital PhotoShot™ Mode Use this feature to record a seven second (approx.) still image from the current camera picture. Audio is also recorded for on-thespot narration. Or, you can add narration later with the Audio Dubbing feature to make an interesting slide show, etc. (p. 44) 1 2 Set POWER to CAMERA. Press PHOTOSHOT in Record/Pause mode. “PHOTO” will appear in the EVF or the LCD monitor.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Camera Recording Zoom You can gradually zoom in for close ups or zoom out for wide angle shots. 2POWER 1 2 ZOOM 1POWER Set POWER to CAMERA. Zoom slowly : by lightly pressing the “T” (Telephoto) or the “W” (Wide Angle) side of the POWER ZOOM. Zoom quickly: by applying more pressure. Start recording. Note 3REC/PAUSE • The zooming speed ranges from a slow 17 seconds to a fast 1.5 seconds according to the amount of pressure applied to the POWER ZOOM.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Camera Recording Recording Check To playback the final few seconds of the last recorded scene in the REC/PAUSE mode. 1 Press RECORDING CHECK briefly in the REC/PAUSE mode. The [CHK] indication appears. After checking, the Palmcorder returns to the REC/PAUSE mode. • For Recording Check, the Palmcorder must be in the same mode (SP or LP) as was used for recording, otherwise the playback picture is distorted.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features CINEMA Mode You can record a picture compatible with a wide-screen TV equipped with an S2 picture terminal. 3, 4 JOG KEY 1 2 3 1POWER 2MENU 5REC/PAUSE 5 Backlight Use when recording a subject that is darker than the surrounding scene, is in a shadowed area, or when the light source is in back of your subject. 1 2 3 1POWER Press MENU to display the CAMERA mode menu screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Program AE The Auto Exposure feature can be used to make quality recordings in a variety of scene situations. Note • When MagicVu (PV-DV402 only) is ON, Program AE and H.S.S. cannot be set in the menu. 2AUTO/MANUAL 4, 5 JOG KEY 3MENU 1POWER 1 2 3 4 5 6 (No display) Press MENU to display the menu screen. Rotate JOG KEY to select ADJUST , and then press JOG KEY to display the CAMERA ADJUST menu screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Audio/Video Fade In/Out You can make smoother scene transitions for a more professional look. 1, 3, AFADE Fade In Starting the first scene with “fade in” is very effective. 1 2 3 In REC/PAUSE mode, hold down FADE until the picture fades out. Press REC/PAUSE to start recording. Fade Out 2, BREC/ PAUSE MagicVu™ IR Filter (0 Lux) (PV-DV402 only) MagicVu allows you to record video in total darkness.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Picture in Picture (PinP) You can display a PinP (still image) screen on the Main Picture. Note • PinP position is fixed at the bottom right of the screen. 1 2 3 Main Picture Picture in Picture (PinP still image) 4 PHOTOSHOT Set POWER to CAMERA. Press MENU to display the menu screen. Rotate JOG KEY repeatedly to select D.FUNCTION , then press JOG KEY to display the CAMERA FUNCTION menu screen. Press JOG KEY to select PinP .
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Photo Title You can use PhotoShot images stored on a Memory Card to record a WIPE or MIX effect on a cassette. Note When Photo Title is set to ON, the selected image and Title will appear before each recording is made. WIPE : The Photo title is replaced with the current scene in a wiping motion. Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to OFF before inserting a recorded Memory Card.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Advanced Settings White Balance Auto White Balance (“AWB”) automatically maintains optimum color balance in most lighting conditions. However, when using Digital Functions, etc., you may get better results by using the manual adjustment. 3, 4, A, B 1 2 3 JOG KEY 4 1POWER 2AUTO/MANUAL Set POWER to CAMERA. Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Advanced Settings Auto Focus The Palmcorder automatically adjusts the focus over the entire zoom range. Manual Focus 4, 6POWER 1 2 3 4 5 ZOOM 5M.FOCUS DIAL 1POWER 6 2AUTO/ MANUAL Set POWER to CAMERA. Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor. Press FOCUS so that the “MF” (Manual Focus) indication appears in the EVF or the LCD monitor.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Advanced Settings High Speed Shutter To record high speed motion (e.g. tennis stroke) with improved STILL or SLOW MOTION playback when watching the tape on this Palmcorder. Auto Shutter In the AUTO mode (no indication in the EVF and LCD monitor), the Palmcorder will automatically adjust the shutter speed (up to 1/350). • AUTO mode is automatically selected whenever the POWER Switch is set to CAMERA.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Advanced Settings Adjusting the Iris Manually Normally, the Palmcorder adjusts the exposure automatically. However, when the background is extremely bright, or when the subject is backlit, you can compensate by adjusting the Iris manually. 1 2 JOG KEY 1POWER 2AUTO/MANUAL Hold down AUTO/MANUAL for more than 0.7 seconds so that the “MNL” indication appears in the EVF or the LCD monitor.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Playback Your Recordings Playback using the LCD Monitor Before you begin • Connect the Palmcorder to a power source. (pp. 14, 15) • Insert a recorded cassette. You can also use the LCD monitor to playback your recording. 1 1POWER 2 3 4 5 180° 90° 90° 2LCD-OPEN 4PLAY Set the POWER to VCR. • The POWER lamp lights red. • Be sure POWER is fully turned to the VCR position. Press LCD-OPEN to unlock the LCD monitor and swing open.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Playback Your Recordings Repeat Playback 1 1PLAY EVF/LCD R Adjusting the Volume 1, 2 2 1 VOLUME 2 Turn the Palmcorder OFF to exit the Repeat Playback mode. Rotate VOLUME to adjust the volume of the built-in speaker in PLAY mode. • The volume setting screen appears. Press “T” to increase the volume or press “W” to decrease the volume.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Note • Sound is muted during all special effects. A During playback, hold down (FAST FORWARD/SEARCH) or Rapid Visual Search BPLAY B A, B A, B REWIND/ FAST FORWARD/ SEARCH SEARCH Note • When executing a rapid visual search, the picture may become bluish for an instant or mosaic. This is normal during this mode. EVF/LCD STILL Picture 1 2 1, 2PAUSE 2PLAY (REWIND/SEARCH).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Feature Note • Sound is muted during all special effects. Slow Motion Playback (Remote Control Only) 1 Forward Slow: Press SLOW/F.ADV during play. Reverse Slow: SLOW/F.ADV during play. Press 2PLAY 1 1 2 Press PLAY to release. (During reverse slow motion playback, time SLOW/ F.ADV code indication may not change regularly.) SLOW/ F.ADV Note Variable Speed Search 2, 3 JOG KEY 1 2 3 Press (PLAY) to start playback.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Note • Sound is muted during all special effects. Frame by Frame Advance (Remote Control Only) 3PLAY 1 2 1PAUSE 2 2 3 SLOW/ F.ADV 2, 3 1 2 JOG KEY 1MENU 3 4 4INDEX SEARCH (fast forward) 36 Press SLOW/F.ADV to do a frame by frame reverse. Press PLAY to release. • If you hold down SLOW/F.ADV, you can see a continuous series of still images at a slower speed than normal slow mode.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Note • Sound is muted during all special effects. Jog Frame by Frame Search (Palmcorder Only) During Still mode, rotate JOG KEY to advance or reverse the picture one frame at a time. JOG KEY Index Forward/Reverse Search (Remote Control Only) Search for a particular scene by using the electronic index marks placed at the beginning of each recording.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features Strobe Multi Mode In Strobe Multi Mode, you can select the rate at which a succession of still screens are captured from the playback picture. 3, 4 JOG KEY 1POWER 1 2 3 4 Set POWER to VCR. Press MENU to display the menu screen. Rotate and press JOG KEY to select and set MULTI SETTING . Press JOG KEY repeatedly to set desired speed. Strobe Speeds Strobe Speeds 9 screen capture time 2MENU FAST Every 0.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Special Effect Features View Recording/Playback on your TV [ TV with AUDIO/VIDEO IN Jacks ] Before you begin • When using S-VIDEO Connector, insert the DC Cable into the DC IN Terminal. (p. 15) 1 A/V OUT 2 Back of TV Audio In Video In 3 A/V Cable (Supplied) Set POWER to CAMERA or VCR. To view what the Palmcorder is recording or to playback a tape on your TV. Turn your TV ON and set it to LINE INPUT or S-VIDEO.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Digital Features Digital Zoom CAMERA mode This feature is useful when you want to record close-up shots of subjects located beyond a normal zoom range of 1X to 10X magnification. With the digital zooming feature, you can select a magnification of 25X or even to 700X. Note • Other Digital Functions are turned off automatically when the EIS and Digital Zoom are selected. 1 2 3 4 EVF/LCD Zoom In (“T”) D.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Digital Features Digital Zoom (Continued) VCR mode 1 2 3 3, 4 JOG KEY 2MENU 1POWER 5PLAY 4 5 6 Set POWER to VCR. Press MENU to display the VCR MENU screen. Rotate JOG KEY to select PLAY FUNCTION , then press JOG KEY to display the VCR PLAY FUNCTION menu screen. Rotate JOG KEY to select D.ZOOM , then press JOG KEY to select ON. • Press MENU twice to exit. Press (PLAY) to start playback. • The center portion of the image doubles in size.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Digital Features Dual Digital Electronic Image Stabilization System (D.E.I.S.) This feature helps compensate for any unintentional hand or body movement. It can be used in both the Recording and Playback (VCR) modes. CAMERA mode 1 2 Set POWER to CAMERA. Press EIS to stabilize the picture. • Picture flicker may be observed when taping under fluorescent lighting conditions. • The EIS indicator flashes when the light level is inadequate. • Turn D.E.I.S.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Digital Features Other Digital Functions Use the following features to add interest and professionalism to your recordings or playback. Select from twelve special effects. 3, 4, 5 JOG KEY 1 2 3 2MENU 1POWER 4 Types of Digital Functions 5 Press MENU to display the menu screen. Rotate JOG KEY to select D.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Editing Features Audio Dubbing using the External (PV-DV402 only) or Built-in Microphone Before you begin • Connect the external Microphone (if used) (PV-DV402 only). • Turn on the Palmcorder. • Insert a pre-recorded tape to be dubbed. The original sound can be replaced with new sound using the built-in Palmcorder The AUDIO-REC setting in CAMERA microphone or an external microphone MENU mode should be as follows: (PV-DV402 only).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Editing Features 4, 5PAUSE To listen to the desired audio sound, set the AUDIO setting of the VCR mode MENU (Menu OSD: p. 110) as follows: AUDIO:The following selections are available for 12 bit AUDIO dubbed recordings only (sound recorded in SP mode only). Set this position to listen to the ST 1 original sound. Set this position to listen to the ST 2 audio dubbed sound.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Editing Features Copying your Tapes to S-VHS or VHS Cassette Source (Playing) Palmcorder DC Cable (Supplied) S-VIDEO OUT A/V OUT Before you begin • Connect both Palmcorder and VCR to their power sources. • Connect the Palmcorder to a VCR as illustrated left. • Turn ON both units. • Set the recording VCR’s Input Signal Selector to LINE. • Set the Palmcorder POWER to VCR. • Before using S-VIDEO Connector, insert the DC Cable into the DC IN Terminal. (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Editing Features Copying from Digital Equipment (dubbing) Before you begin High quality digital-to-digital copying can be accomplished if both Palmcorders incorporate the DV Input/Output (i.LINK) Connector (DV interface cable (i.LINK) is not supplied). Source (Playing) Palmcorder DV Input/Output (i.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features Before you begin Card PhotoShot You can record still images to a Memory Card. Warning • Memory Card will not work when DV interface Cable (i.LINK) is connected. 3PHOTOSHOT • Connect the Palmcorder to a power source. (pp. 14, 15) • Set POWER to OFF before inserting a Memory Card. (p. 13) 1 2JOG KEY 1POWER 2 M-CARD Lock Slide the M-CARD Lock Switch to unlock, then set POWER to M-CARD. • The POWER lamp lights red.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features Cautions for the Memory Card • While Memory Card data is being read, do not remove it, turn off the power, or subject unit to vibrations and/or shocks. • Do not leave the Memory Card in a place with high temperature, a place exposed to direct sunlight, or a place where electromagnetic waves and static electricity can be generated.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features Playback Still Images You can view the images on the Memory Card. Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) 1 3, 4 JOG KEY Slide the M-CARD Lock Switch to unlock, then set POWER to M-CARD. • “PLAY: PUSH PLAY KEY” is displayed for 10 seconds. 1POWER M-CARD Lock 2M-PLAY 2 Press (M-PLAY) to display the Multi playback screen. • “PLEASE WAIT” appears on-screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features Before you begin Delete Specific Images You can delete unwanted images and increase the remaining image memory. Warning: Once deleted, images cannot be restored. DELETE PAGE Delete specific images from a page. DELETE ALL Delete all images. (p. 52) • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) 1 2 FORMAT Delete all data. (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features Delete All Image Pages You can delete all images from the Memory Card easily with this operation. Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) Warning: Once deleted, images cannot be restored. 2, 3 1 2 JOG KEY 2M-DEL M-STOP Press (M-DEL) to display the DELETE menu. Then, rotate and press JOG KEY to select ALL . • The screen below is displayed.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features Format the Memory Card You can easily format your Memory Card using this operation. Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) Warning: Formatting permanently removes all image data. 2, 3 1 2 JOG KEY 2M-DEL Press (M-DEL) to display the DELETE menu, then rotate and press JOG KEY to select FORMAT . • The screen below is displayed.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Card Features DPOF Setting You can select the images to be printed, the number of prints, and other print-related information (DPOF setting) on a Memory Card. “DPOF” stands for Digital Print Order Format, and since printing data can be added to images on the Memory Card, the Memory Card can be used with any system that provides DPOF. VARIABLE: You can select images recorded on the Memory Card and set the number of prints desired.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Transferring Your Images (Windows) You can transfer images from your Palmcorder tape to your PC (Personal Computer).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Transferring Your Images (Windows) Software Installation (Windows 95 (for ArcSoft Software only/ 98SE/Me/2000/XP) Caution • Please install Palmcorder USB Device Driver first before connecting the Palmcorder and your PC using USB Cable. Once Palmcorder USB Device Driver is installed, you must restart your computer for installation to take effect.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Transferring Your Images (Windows) Notes on PHOTOVU/MPEG4 Movie Messenger™ System operation • For PHOTOVU/MPEG4 Movie Messenger™ System, do not connect the i.LINK and USB terminals to the Palmcorder at the same time. • Make sure Palmcorder power is not shut off during use as your PC system may become unstable. Therefore, the AC Adaptor should be used as the power source.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Connection (for PHOTOVU/MPEG4 Movie Messenger™ System) 2 USB Terminal USB Terminal 3 1 Turn on your PC. 2 Set the Palmcorder POWER to VCR. USB Cable (supplied) For Windows XP users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CAPTURE” appears in the EVF or the LCD monitor. • The “Found New Hardware Wizard” screen of Windows is displayed.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System For Windows 2000 users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CAPTURE” appears in the EVF or the LCD monitor. • The “Found New Hardware” screen of Windows is displayed. • When the Palmcorder and PC (with Windows 2000) are connected via USB, a message, such as the one below, is displayed. The following message is displayed.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Running the PHOTOVU/ MPGE4 Movie Messenger™ System* * PHOTOVU: You can transfer Still images from your Palmcorder tape to a PC. MPEG4 Movie Messenger™ System: You can transfer Motion images from your Palmcorder tape to a PC. Before you begin • Insert a recorded tape. (p. 11) 1 2 3 4 Set Palmcorder POWER to VCR. Connect the Palmcorder to your PC using the USB Cable (supplied) or DV interface Cable (i.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Using Tape Image Data (USB) By connecting the Palmcorder and PC with the USB Cable, you can transfer Motion images and Still images saved on the DV Tape directly to your PC. Note • Detail mode cannot be used with a USB connection. • Deactivate your PC ScreenSaver or this application may shutdown during image capture. Before you begin • Insert a recorded tape. (p. 11) • Make Palmcorder-PC connections. (pp.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Playing back the saved Motion and Still images You can play back the saved Motion images and Still images (p. 61) for confirmation. 1 2 Repeat steps 1~4 on page 60 to run the PHOTOVU/MPEG4 Movie Messenger™ System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System VideoGift Screen You can use these features using the VideoGift Screen. 14 1 9 2 10 3 11 4 12 5 15 16 13 6 7 8 17 10 Settings 2 11 3 4 5 6 7 8 9 Drag the pointer of the playback start position. Movie Mode You can display motion images. Open Movie You can open folders containing video files (*.AVI, *.WMV). Open Audio You can open folders containing audio files (*.WAV).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Using the VideoGift Screen 1 2 Repeat steps 1~4 on page 60 to run the PHOTOVU/MPEG4 Movie Messenger™ System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users 2 VideoGift 3 • If warning indication is displayed, please see page 89. Click [View Manager] to display the View Manager screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Setting the Mail Software 1 2 It is possible to set the mail software to start up automatically when [E-Mail] of VideoGift is clicked. Note The e-mail Software must support MAPI (Messaging Application Programming Interface).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Attaching captured Motion and Still images to your e-mail You can transfer and compress your Motion images as attachments to your e-mail easily. Before you begin • Insert a recorded tape. (p. 11) • Make Palmcorder-PC connections. (pp. 58, 59) • Turn your PC on. (p. 58) • Set Palmcorder POWER to VCR. 1 2 2VideoGift Repeat steps 1~4 on page 60 to run the PHOTOVU/MPEG4 Movie Messenger™ System.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Sending a Portion of a Motion Image 1 2 Repeat steps 1~4 on page 60 to run the PHOTOVU/MPEG4 Movie Messenger™ System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users 1 2 7E-Mail 6Preview 7Uploader 3 4 5 6 7 • If warning indication is displayed, please see page 89. Select a Motion image.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Setting the Size and Quality of Motion and Still Image 5 1 2 5 Repeat steps 1~4 on page 60 to run the PHOTOVU/MPEG4 Movie Messenger™ System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen. Caution for Windows 2000 users • If warning indication is displayed, please see page 89.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Selecting a Frame from a Motion Image This screen is displayed when an individual frame from a moving image file is to be added as a still image. 1 2 Repeat steps 1~4 on page 60 to run the PHOTOVU/MPEG4 Movie Messenger™ System. Click [VideoGift] to display the VideoGift screen. • The image captured last is displayed in the VideoGift screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System Uploading the image to PictureStage Home Page* You can upload edited moving images and still images to the PictureStage Home Page. Before you begin • Attain internet access. • Before using this feature, you must become a registered member of PictureStage. For details on installation, settings, etc., please visit http://www.piturestage.com/ (current as of Dec. 28, 2001).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System 5 6 7 Click [Upload To Photo Album] to upload the Still Image or [Upload To Video Album] to upload the Motion Image. • The “PictureStage Video (Image) Uploader” screen is displayed. • Click [Exit] to exit uploader. Enter your login ID and password, and then click [Continue]. • Click [Free Sign up] if you have no login ID. The PictureStage Home Page opens and there you can get a login ID and password.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Transferring Your Images (i.LINK) (Windows) PC Connection with DV Interface Cable (i.LINK) A video clip can be transferred directly to your PC (Personal Computer) via a DV Interface Cable (i.LINK) (not supplied) using products and software from a number of editing software companies including Canopus and Pinnacle. Using products from these companies allows you to capture and edit video clips using the DV interface (i.LINK).
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System (i.LINK) Before you begin Using Tape Image Data By connecting the Palmcorder and PC with the DV Interface Cable (i.LINK), you can transfer Motion images and still images saved on the DV Tape directly to your PC. Note • If PHOTOVU/MPEG4 Movie Messenger™ System does not work, please refer to note on page 72. • Deactivate your PC ScreenSaver or this application may shutdown during image capture.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 PHOTOVU/MPEG4 Movie Messenger™ System (i.LINK) 3Normal 3, 3Detail 4Movie Capture 4Still Capture DV 6STOP [When selecting Detail] Note • Detail mode lets you specify the start and end frames for the video segment you want to capture and save. 3 4 5 5, 7, 5Select 6 7 To capture Still images [When selecting Detail] 3 4 5 74 Click on [Detail]. Click on [Movie Capture] at the point you wish to capture a Motion image.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder USB Device Driver/SD Drive Connection (for Palmcorder USB Device Driver/SD Drive) 2 USB Terminal USB Terminal 3 1 2 USB Cable (supplied) Turn on your PC. Set the Palmcorder POWER to M-CARD. For Windows XP users 3 1 2 3 Note • When connecting for the first time using Windows XP, the OS installation CD may be required. Follow the instructions as they appear on your PC screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder USB Device Driver/SD Drive For Windows 2000 users 3 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “CONNECT WITH PC” appears in the EVF or the LCD monitor. • The “Found New Hardware” screen of Windows is displayed. • When the Palmcorder and PC (with Windows 2000) are connected via USB, a message, such as the one below, is displayed. The following message is displayed.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder USB Device Driver/SD Drive Using Memory Card Image Data By connecting the Palmcorder and PC with the USB, you can transfer Still images saved on the Memory Card directly to your PC. Before you begin • Install the Palmcorder USB Device Driver. (p. 56) • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) • Make Palmcorder-PC connections. (pp. 75, 76) • Turn your PC on. (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder File Converter Using Palmcorder File Converter You can convert the JPEG data of your PC into DCF (Design rule for Camera File System) data, and transfer this data to your Palmcorder via USB. 1 2 3 4 Set Palmcorder POWER to M-CARD. Connect the Palmcorder to your PC using the USB Cable (supplied). (pp. 58, 59) Click on “Start,” “(All) Programs,” “Panasonic,” “Palmcorder,” then “File Converter 3.0.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder File Converter 6 7 Select the folder to which the converted file is to be saved. • The Conversion results screen is displayed. Use “Help” for detailed instructions. When selecting “To convert format for Panasonic Digital Palmcorder” 5 7 PC Connection 6 Select the file to be converted. Select the drive to which the converted file is to be saved. • The Conversion results screen is displayed. Use “Help” for detailed instructions.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera Before Using Web Camera* Features Web Camera* MSN Messenger and NetMeeting are software that can be linked and used together. Using the Palmcorder and the internet, you can communicate with others by having picture and sound similar in fashion to a videophone. Please read this first • To use the Web Camera feature, Microsoft’s Windows Messenger, MSN Messenger Service, and Windows NetMeeting are required.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera Connection (for Web Camera) Lch (White) AV OUT A/V Cable (supplied) To MIC Terminal Audio Adaptor (supplied) USB Terminal 1 USB Terminal 1 2 USB Cable (supplied) Turn on your PC. Set the Palmcorder POWER to CAMERA. For Windows XP users 3 1 2 3 • “CONNECT WITH PC” and “WEB CAM” are displayed in the EVF and LCD monitor. A gray box is also displayed. The image within the box can be used with communication.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera For Windows 2000 users 3 4 Connect the Palmcorder to your PC (Windows) using the USB Cable (supplied). • “Found New Hardware” is displayed. • “CONNECT WITH PC” and “WEB CAM” are displayed in the EVF and LCD monitor. A gray box is also displayed. The image within the box can be used with communication. • Place the Palmcorder so that you are in the picture.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera (For Windows XP users) For Windows Messenger (Windows XP only) When Windows Messenger is newly installed or when run the first time, the following settings become necessary. For more details, please read the respective Help file. Note • Once settings are performed, they are not required from the second time the software is run. Before you begin • Be sure you have a dial-up connection.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera (For Windows XP users) 5 Type in your E-mail address and password. • You’ll need to get a hotmail address. If you do not have one, click on [Get a .NET Passport]. Please carefully read the displayed contents and then proceed. There are times when a Version Upgrade screen will be displayed. However, if you are using Windows Messenger 4.5 or newer, there is no need to upgrade. 6 Click on [Audio Tuning Wizard] in the [Tools] menu.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera (For Windows XP users) 8 The person calling (inviting) side Double-click a person to call from those currently [on-line]. • “xxxx-conversation” screen is displayed. 9 The person calling (inviting) side Click [Start Camera] in the “xxxconversation” screen. • A message inviting the other person is displayed. The invited person side A message asking if the person accepts or declines is displayed. Click [Accept] on the screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera (For Windows 98SE/Me/2000 users) For MSN Messenger Service and Windows NetMeeting (Windows 98SE/Me/2000) When MSN Messenger Service is newly installed or when run the first time, the following settings become necessary. For more details, please read the respective Help file. Note • Once settings are performed, they are not required from the second time the software is run. Before you begin • Be sure you have a dial-up connection.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera (For Windows 98SE/Me/2000 users) 6 Click on [Audio Tuning Wizard] in the [Tools] menu. Note • You can set the volume for playback or mic volume, etc. • Also, confirm that the Palmcorder and PC are connected correctly. The person you wish to access needs to do settings 1~6 also. 7 Select [Tools] -> [Add a Contact] to register the person you wish to access in MSN Messenger Service.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Web Camera (For Windows 98SE/Me/2000 users) 9 The person calling (inviting) side Click [Start NetMeeting] in the “xxxconversation” screen. The invited person side The Instant Message screen appears and a confirmation message is displayed. Click on [Accept]. The NetMeeting screen is automatically opened. Note 10 11 12 13 The first time Windows NetMeeting is run, etc., the Setup screen is displayed. Please carefully read the contents and then proceed.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Warning Indications Windows 2000 In Windows 2000, startup PHOTOVU/ MPEG4 Movie Messenger™ System. Clicking on [VideoGift] may cause the following type of error to occur. If so, please perform the following instructions. Download and install Media Player (7.1 or newer), go to http://www.microsoft.com/windows/ mediaplayer (current as of Dec. 28, 2001). • “Windows Media. com: Download” is opened. Click [Download Now!] on the screen.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Transferring Your Images (Macintosh) You can transfer images from your Palmcorder tape to your Macintosh. System Requirements (for Built-in SD Drive/ArcSoft Software) • Mac OS 9.0~9.1 • Mac OS 8.6~9.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Transferring Your Images (Macintosh) Using Built-in SD Drive Before you begin • Set POWER to OFF before inserting a recorded Memory Card. (pp. 48, 49) 1 2 3 4 Set the Palmcorder POWER to M-CARD. Connect the Palmcorder to your Macintosh using the USB Cable (supplied). (p. 90) • “PLEASE WAIT”, “CONNECT WITH PC”, and “STORAGE” is displayed on the LCD monitor. Double click the “Untitled” icon.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder Accessory System Accessory # Description Figure Price PV-DAC11A AC Adaptor with AC Cable and DC Cable Call For Pricing CGR-D08A/1B 800mAH / 1 h 30 min, Battery Pack $69.95 1 600mAH / 3 h, Battery Pack $99.95 CGP-D28A/1B 2 800mAH/ 5 h, Battery Pack $129.95 CGR-D53A/1K 5 300mAH / 9 h, Battery Pack $229.95 PV-DDC9 DV Interface Cable (i.LINK) (4-pin to 4-pin) $55.00 PV-DRC9 IR Remote Control $29.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Palmcorder Accessory Order Form Please photocopy this form when placing an order. 1. Palmcorder Model # 2. Items Ordered Accessory # Description Price Each Quantity Total Price Subtotal Your State & Local Sales Tax Shipping & Handling 6.95 Total Enclosed 3. Method of payment (check one) Check of Money Order enclosed (NO C.O.D.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Notes On Operations Before you begin Replacing the Bulb 1 • Set POWER to OFF. Insert a rigid wire, such as an extended paper clip into point (A) and lift cover up. 3 Replace bulb using a clean cloth or tissue. (Do not touch with fingers.) (A) 4 2 Replace lens cover. Using Tweezers or needle-nose pliers, carefully remove bulb. • Take unit to servicenter if you need assistance. Note • Handle bulb gently. Excessive force may cause bulb to crack.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Notes On Operations Approximate Brightness Values Your Palmcorder has been designed for normal scene illumination of 150 footcandles (1500 lx). However, the Palmcorder may be used at F1:1.8, if illumination is more than 0.5 footcandles (5 lx). The table below shows the color temperature for reference.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Specifications Power Source: Palmcorder: 7.2 V DC (Battery) 7.8 V DC (AC Adaptor) AC Adaptor: 110/120/220/240 V AC, 50/60 Hz Battery: Lithium-Ion Type DC 7.2 V Power Consumption: Palmcorder : 7.2 V/7.8 V DC 6.5 W (Max. 9.5 W) AC Adaptor : 18 W 1 W (when not in use.) Digital Interface USB/i.LINK (IEEE1394) Video Signal: EIA Standard (525 lines, 60 fields) NTSC color signal Video Recording System: 2 rotary heads.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Requesting Service Cleaning Care for Video Heads Clogged Video Head (a) Video Head Cleaning: Normally, your Palmcorder will not require head cleaning. However, it is possible that the heads may become clogged due to dust in the air, playing damaged tapes, long term use, etc. If “NEED HEAD CLEANING” appears for 5 seconds in the EVF or LCD monitor, the heads may require cleaning.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Before Requesting Service If you have a problem with your Palmcorder, it may be something you can correct yourself. Check the list below for symptoms and corrections. Symptom Correction No picture in the EVF or LCD Monitor... • Make sure the Power Source is connected. (pp. 14, 15) • Make sure the POWER switch is set to VCR or CAMERA. (pp. 18, 32) • Check the Dew Indicator. (p. 99) • Make sure the Battery is fully charged. (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 On-Screen Displays (OSD) The following warning displays appear in the EVF and the LCD monitor. Indications Condition If the Palmcorder is in CAMERA mode without a cassette inserted, “ ” will flash and “TAPE NOT INSERTED” will appear for 5 seconds. Recording will not start. If the Palmcorder is in CAMERA mode or Audio dub mode with the cassette sliding record tab opened, “ ” will flash and “CHECK REC TAB” will appear for 5 seconds.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 On-Screen Displays (OSD) Indications Condition If you play a tape recorded in a format other than NTSC or you try to copy copy-protected data, “INCOMPATIBLE DATA” will appear. When a still image is transferred from a tape to an already full Memory Card, or when setting is DPOF, “NO SPACE LEFT” appears. If the Palmcorder is in M-CARD mode or Photo Title (CAMERA mode) and the DV Interface Cable (i.LINK) is connected, “DISCONNECT DV CABLE” appears.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Request for Service Notice Please photocopy this form when making a request for service notice. Request for Service Notice: In the unlikely event this product needs service. • Please include your proof of purchase. (Failure to due so will delay your repair.) • To further speed your repair, please provide an explanation of what is wrong with the unit and any symptom it is exhibiting.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Limited Warranty Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America, One Panasonic Way Secaucus, New Jersey 07094 Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc. AVE. 65 de Infantería, Km. 9.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Servicenter List For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquiries please contact: 1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST. or send e-mail to : consumerproducts@panasonic.com Web Site: http://www.panasonic.com You can purchase parts, accessories or locate your nearest servicenter by visiting our Web Site.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Spanish Quick Use Guide/Guía Para Uso Rápido Precauciones para su seguridad ADVERTENCIA: PARA EVITAR INCENDIOS Y DESCARGAS ELÉCTRICAS, NO EXPONGA ESTE EQUIPO A LA LLUVIA NI A LA HUMEDAD. Palmcorder está diseñada para grabar y reproducir en el modo de Reproducción Su Mini Estándar (SP) y modo Largo (LP). Se recomienda el uso sólo de cintas de cassette que hayan sido probadas e inspeccionadas para su uso en aparatos VCR con la marca Mini .
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Spanish Quick Use Guide/Guía Para Uso Rápido Antes de comenzar Inserte de la batería • Cargue la battería. (Página 14.) Film de protección Nota • Retire la película protectora antes de utilizarlo. 2 1 1 Coloque la batería y deslícela hacia arriba hasta que se quede bloqueada con un clic. Insert Cassette Esta videocámara contiene un sistema de ejecución fácil del cassette.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Spanish Quick Use Guide/Guía Para Uso Rápido Grabación con la cámara Cuando el monitor LCD se enchuentra totalmente abjerto, el visor se DESACTIVA automàticamente. 1 2 Ajuste el interruptor de alimentación (POWER) a la posición CAMERA. Ajuste el control lde ajuste de visión según lo desee. Visor 180° 90° 4 Monitor LCD Presione el botón de grabación/ pausa (REC/PAUSE) para iniciar la grabación.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Spanish Quick Use Guide/Guía Para Uso Rápido Antes de comenzar Introducir la Tarjeta de memoria* • Cargue la battería. (Pàgina 14.) *Tarjeta de Memoria: Tarjeta MultiMedia o Tarjeta de Memoria SD (Pàgina 94.) • Asegúrese de introducir la Tarjeta de memoria antes de utilizar la tarjeta PhotoShot. (Página 48.) A continuación se indican una lista de Tarjetas de Memoria soportadas por esta unidad.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 MENU OSD Camera Mode Menu Screen 4 1 5 2 3 6 4 5 7 6 7 8 8 9 10 11 12 1 2 3 9 D.FUNCTION (pp. 41, 43) To select one of the 10 digital functions. Setting to OFF cancels the previously selected digital function. D.ZOOM (p. 40) To select D.ZOOM1 (from 10X to 25X) or D.ZOOM2 (from 10X to 700X). Setting to OFF cancels the previously selected digital zoom. PROGRESSIVE (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 MENU OSD 13 13 14 15 14 16 17 18 19 15 20 16 17 21 22 18 19 20 22 109 113 For Your Information 21 REMOTE (p. 10)ly VCR1: To receive signals from the Remote Control, set to VCR1. VCR2: To receive signals from the Remote Control, set to VCR2. OFF: To prevent reception of signals from the Remote Control. BEEP Set to ON to hear beep when starting and stopping camera recording or when unusual conditions occur. To cancel the beep, set to OFF.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 MENU OSD VCR Mode Menu Screen 4 1 2 3 5 4 6 5 7 6 7 8 9 8 10 1 2 3 D.FUNCTION (p. 43) To select one of the 6 digital functions. Setting to OFF cancels the previously selected digital function. D.EFFECT (p. 43) To select one of the 2 digital picture effects for playback. Setting to OFF cancels the previously selected digital effect. D.ZOOM (p. 41) Set to ON to double the size of a playback image.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 MENU OSD 11 11 12 12 13 14 13 15 14 15 DISPLAY (p. 113) To select the desired type of display and counter indication displayed on the LCD Monitor or in the viewfinder. C.RESET (p. 113) Setting to ON resets the counter to zero. DATE/TIME (p. 112) The date and time can be set and displayed on the screen. CLOCK-SET (p. 16) When set to ON, the date and time can be set on the screen. LCD/EVF SETTING (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Electronic Viewfinder/LCD Monitor Indications Here are some of the basic indications which will appear on the Palmcorder EVF and LCD Monitor. Only Date and Time indications will be recorded onto the tape. CAMERA/VCR Mode h a i j b c d e f g a g Battery Remaining FULL EMPTY b Tape Remaining (AY-DVM30EA) Date and Time Indication (Menu OSD: pp.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Electronic Viewfinder/LCD Monitor Indications CAMERA/VCR Mode k m l IMPORTANT NOTE: • Display must be set to ON for MF, AE, W.BALANCE or BACK LIGHT indications to be displayed on the EVF or LCD Panel selected. l Display ON/OFF and Counter/Time Code • when C.RESET does not work when DISPLAY The indication switches as shown is set to OFF and T.CODE. below when the desired “DISPLAY” mode is selected from the menu. m Tape Mode Indications (Menu OSD: pp.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Electronic Viewfinder/LCD Monitor Indications CAMERA/VCR Mode n o p q s t r u v w x y n Zoom Magnification Level (p. 40) v o Digital EIS Indications (p. 42) This display appears when EIS is pressed. Z.MIC Indication (Menu OSD: p. 108) This display appears when ZOOMMIC is set to ON. w Backlight Indication (p. 23) This display appears when BACK LIGHT is pressed. Light Indication (p. 9) This display appears when LIGHT is set to ON.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Electronic Viewfinder/LCD Monitor Indications PHOTO Mode [ Photo Rec Mode ] [ Photo Play Mode ] c a b d e f g h [ Photo Play Mode ] a REC MODE • NORMAL or FINE mode. • Image Size: “NORMAL” mode 640 x 480 pixels “FINE” mode 1 280 x 960 pixels c Recording Mode POWER is set to PICTURE. d Directly/Image Number e DCF NO. (Design rule for Camera File system) Indication (Menu OSD: p. 111) f DPOF Indication (p.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Index of Controls Front View Built-in Twin Capsule 2-Way Microphone System MAGICVU/0LUX (PV-DV402 only) p. 25. Shoulder Strap Attachment Ring p. 8. Lens BATT RELEASE pp. 14, 15. Remote Sensor p. 9. Built-in Light pp. 9, 94. M-CARD Door p. 13. Side View JOG KEY pp. 16, 17. M.FOCUS DIAL p. 29. External Microphone Jack (PV-DV402 only) p. 44. M-CARD EJECT p. 13. Built-in Speaker p. 33. Shoulder Strap Attachment Ring p. 8. Hand Strap p. 8.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Index of Controls Rear View PHOTOSHOT pp. 20, 48, 49. Electronic Viewfinder (EVF) p. 12. POWER ZOOM pp. 21, 40. VOLUME p. 33. MENU pp. 16, 17. A/V Output Connector pp. 39, 81. PHONE p. 32. Lens Cap p. 8. Top View PAUSE pp. 34, 45, 47. CAMERA STILL p. 26. M-DEL pp. 51, 52, 53. FOCUS p. 29. AUTO/MANUAL pp. 28~31. PLAY pp. 12, 32. M-PLAY pp. 50, 51. MULTI p. 38. FADE p. 25. REC p. 47. LIGHT p. 9. STOP pp. 12, 32. M-STOP pp. 50~53. EIS p. 42.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Index of Controls AC Adaptor AC Power Cord pp. 14, 15. POWER Lamp pp. 14, 15. CHARGE Lamp p. 14. VCR DC Output Connector p. 15. CAUTION: This unit will operate on 110/120/ 220/240 V AC. An AC plug adaptor may be required for voltages other than 120V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug.
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Index F Fast Forward/Rewind Check .. 34 Focus ............................ 29 Format the Memory Card .... 53 Frame by Frame Advance ... 36 H Hand Strap ...................... 8 High Speed Shutter ...... 30 I Important Safeguards ..... 3 Index of Controls . 116~118 Index Search ........... 36, 37 Iris ................................. 31 J Jog Search .................... 37 L LCD/EVF Setting .......... 19 Lens Cap .............. 6, 8, 18 Lens Cap Strap ..
PV-DV52 / PV-DV52-S / PV-DV102 / PV-DV202 / PV-DV402 Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way Secaucus, New Jersey 07094 Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, Inc. Ave. 65 de Infanteria, Km. 9.
