p001-019(PT-LM2E)en 05.02.28 15:43 ページ 1 LCD Projector Commercial Use Operating Instructions Model No. POWER PT-LM2E INPUT VIDEO AUTO SETUP RGB MENU ENTER SHUTTER FREEZE STD VOLUME D.ZOOM INDEX WINDOW PROJECTOR Before operating this product, please read the instructions carefully and save this manual for future use.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 3 FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark ASA or the BSI mark on the body of the fuse.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 4 Contents Preparation IMPORTANT SAFETY NOTICE ...2 Precautions with regard to safety .........................................5 Accessories .................................9 Before use ..................................10 Location and function of each part...........................................12 Getting started Setting-up...................................17 Projection methods, Projector position, Projection distances Connections...............................
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 5 WARNING If you notice smoke, strange smells or noise coming from the projector, disconnect the mains plug from the mains socket. B Do not continue to use the projector in such cases, otherwise fire or electric shocks could result. B Check that no more smoke is coming out, and then contact an Authorised Service Centre for repairs. B Do not attempt to repair the projector yourself, as this can be dangerous.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 6 Do not do anything that might damage the mains lead or the mains plug. B Do not damage the mains lead, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. B If the mains lead is used while damaged, electric shocks, short-circuits or fire may result. B Ask an Authorised Service Centre to carry out any repairs to the mains lead that might be necessary.
Do not use the projector in a bath or shower. B Fire or electric shocks can result. Do not look into the lens while the projector is being used. B Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes. B Be especially careful not to let young children look into the lens. In addition, disconnect the mains lead when you are away from the projector. Do not place your hands or other objects close to the air outlet port.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 8 When inserting the batteries, make sure the polarities (+ and -) are correct. B If the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Use only the specified batteries. B If incorrect batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 9 Check that all of the accessories shown below have been included with your projector. Card remote control unit Lithium battery for (N2QADC000008 x1) remote control unit (CR2025 x1) POWER RGB signal cable [1.8 m (5´10˝), K1HA15DA0002 x1] INPUT VIDEO RGB AUTO SETUP MENU ENTER FREEZE SHUTTER STD VOLUME Mains lead for Continental Europe (K2CM3DR00002 x 1) Mains lead for U.K. (K2CT3DR00005 x 1) D.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 10 Before use Caution when moving the projector Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory softcase. When placing the projector inside the softcase, position it so that the lens is facing upward. Attach the lens cover so that the direction of the “Panasonic” logo becomes as shown in the figure above.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 11 Preparation Notes on use In order to get the best picture quality Draw curtains or blinds over any windows and turn off any fluorescent lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. Do not touch the surfaces of the lens with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 12 Location and function of each part Projector # $ % & D. ZO OM IN WI DE ND X OW ST D VO LU ME FR EE ZE , PR OJ EC TO R P AU SE TO TU EN TE R PO W ER SH UT TE R VI DE O ME NU IN PU T RG B ( ' + * ) ( # Focus ring (page 23) $ Zoom ring (page 23) % Speaker & Projector control panel (Top) (page 14) ' Remote control unit holder Store the remote control unit as shown in the figure above.
Preparation p001-019(PT-LM2E)en 04.12.25 9:27 ページ 13 Projector # $ % & ( ' # Connector panel (page 16) $ Air outlet port Do not cover this port. % Air inlet port Do not cover this port. & Lamp unit holder (page 50) ' Front adjustable legs (L/R) (page 23) ( Air inlet port, Air filter (page 49) Do not cover this port. NOTE: B During projection of an image, the cooling fan will operate, emitting a small noise as it operates.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 14 Projector control panel ˛# ' ( Menu operation ) $ * % & +, Remote control unit ' ) POWER ( INPUT VIDEO RGB * + AUTO SETUP MENU , ENTER . / FREEZE SHUTTER 0 STD VOLUME D.
# Power indicator (pages 22, 24 and 25) This indicator illuminates red when the projector is in standby mode, and it illuminates green when a picture starts to be projected. $ TEMP indicator (page 47) This indicator illuminates if an abnormally high temperature is detected inside the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 16 Connector panel # $ % ( & ' ) # Menu operation (on connector panel) (page 14) $ RGB IN connector (pages 19 and 20) This connector is used to input RGB signals and YPBPR signals. % S-VIDEO IN connector (pages 20 and 39) This connector is used to input signals from a S-VIDEO-compatible equipment such as a video deck.
p001-019(PT-LM2E)en 04.12.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 18 Projector position SH Top edge of screen L: Projection distance SH: Image height SW:Image width H1: Distance from centre of lens to bottom edge of projected image Screen H1 L 63.5 (2-1/2) Bottom edge of screen SW L Screen Projection distances Screen size (4:3) Diagonal length 0.84 m(33˝) 1.01 m(40˝) 1.27 m(50˝) 1.52 m(60˝) 1.77 m(70˝) 2.03 m(80˝) 2.28 m(90˝) 2.54 m(100˝) 3.81 m(150˝) 5.08 m(200˝) 6.35 m(250˝) 7.
p001-019(PT-LM2E)en 04.12.25 9:27 ページ 19 Connections B Read the instruction manual for each peripheral device carefully before connecting it. B Turn off the power supply for all peripheral devices before making any connections. B If the cables necessary for connection are not included with the peripheral device or available as an option, you may need to prepare a proper cable for the device concerned. B If there is a lot of jitter in the video signal, the projected image may flicker.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 20 Connecting to video equipment D-sub15-pin (male) - BNCx5 (male) adapter cable Red (connect to PR signal connector) Blue (connect to PB signal connector) Green (connect to Y signal connector) DVD player (with component video jack) BNC/RCA adapter DVD player Video deck NOTE: B If the signal cables are disconnected or if the power supply for the computer or video deck is turned off while “D.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 21 Preparation for the remote control unit Insert the accessory lithium battery while making sure that the polarities are correct. # While pushing the battery holder tab to the right, pull out the battery holder. Back side Pull out $ Insert the battery into the battery holder so that the + side is facing upward. Match the “+” surface of the battery with the “+” marked side of the battery holder. % Insert the battery holder.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 22 Turning on the power Before turning on the power 1, Ensure that all peripheral devices are connected properly. 2, Remove the lens cover. POWER $ INPUT VIDEO # Mains lead RGB & AUTO SETUP MENU ( ENTER ) * SHUTTER FREEZE STD VOLUME D.ZOOM INDEX WINDOW PROJECTOR ' Lens cover Power indicator the accessory mains lead to the AC IN # Connect socket. BThe power indicator on the projector will illuminate red. the POWER button.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 23 the input select button to select the & Press input signal. Input select buttons RGB VIDEO RGB VIDEO RGB S-VIDEO S-VIDEO BA picture will be projected in accordance with the selected input signal. BWhen a YPBPR signal is being input, “YPBPR” will be displayed instead of “RGB”. Follow the procedure below when you set the projector up first, and when you change the setup place.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 24 Turning off the power Power indicator # POWER INPUT VIDEO AUTO SETUP RGB MENU ENTER FREEZE SHUTTER $ STD VOLUME D.ZOOM INDEX WINDOW PROJECTOR % Mains lead the POWER button. # Press B“POWER OFF” is displayed on the screen. POWER OFF OK CANCEL the I or H button to select “OK”, and $ Press then press the ENTER button. BThe lamp unit will switch off and the picture will stop being projected.
Direct power off function You can disconnect the mains lead during projection or immediately after use and move the projector. The cooling fan will operate by the internal power supply to cool down the lamp. B When this function is used, it may take more time for the lamp to turn back on again compared to when the lamp cools down with the mains lead connected. B Do not put the projector in a bag while the cooling fan is operating.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 26 Correcting keystone distortion and automatic positioning (AUTO SETUP) This projector detects its degree of tilt and the input signal. Keystone distortion and the position of the image can then be corrected automatically in accordance with the input signal. POWER Press the AUTO SETUP button. (When the projected image has caused keystone distortion) INPUT VIDEO AUTO SETUP RGB MENU Screen ENTER SHUTTER FREEZE Projected image STD VOLUME D.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 27 Turning off the picture and sound momentarily (SHUTTER) The “SHUTTER” function can be used to momentarily turn off the picture and sound from the projector when the projector is not being used for short periods of time, such as during breaks in meetings or when carrying out preparation. The projector uses less power in “SHUTTER” mode than it does in normal projection mode. POWER INPUT VIDEO RGB AUTO SETUP MENU Press the SHUTTER button.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 28 Enlarging the picture (D.ZOOM) POWER Press the D.ZOOM +/- button. INPUT VIDEO AUTO SETUP RGB MENU ENTER FREEZE SHUTTER STD VOLUME D.ZOOM INDEX WINDOW B The picture will then be enlarged to 1.5 times the normal size. [ PROJECTOR The remote control unit functions during D.ZOOM (digital zoom) Press the F,G,IandHbuttons to move the enlarged area which you want to project. Press the D.ZOOM +/- buttons to change the enlargement ratio.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 29 Displaying two screens (INDEX WINDOW) This function lets you store a picture which is being projected into memory, so that you can display a still picture and a moving picture on the screen. AUTO SETUP Press the INDEX WINDOW button. B The aspect ratio of the screen changes and the image is vertically elongated in comparison to a normal image. MENU ENTER FREEZE Still picture SHUTTER STD VOLUME Moving picture D.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 30 On-screen menus Menu screens The various settings and adjustments for this projector can be carried out by selecting the operations from on-screen menus. The general arrangement of these menus is shown below. MAIN MENU MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION1 OPTION2 SECURITY SELECT ENTER PICTURE menu (page 35) When an RGB signal is being input EXIT B Press the MENU button to display the “MAIN MENU”.
p020-039(PT-LM2E)en 04.12.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 32 Menu operation guide POWER INPUT VIDEO AUTO SETUP RGB MENU ENTER SHUTTER FREEZE STD VOLUME D.ZOOM # Press the MENU button. The “MAIN MENU” MENU will be displayed. KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION1 OPTION2 SECURITY SELECT ENTER EXIT INDEX WINDOW PROJECTOR Menu operation (on connector panel) $ Press the F or G button to select an item. Selected item will MENU be displayed in KEYSTONE blue.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 33 & Press the F or G button to select an item, and then press the I or H button to change or adjust the setting. An individual adjustment screen such as the one shown below will be displayed for bar-scale items. BRIGHT 32 The bar scale will turn green when any adjustment changes the setting from the factory set value. Unavailable on-screen menu items This projector has unadjustable items and unusable functions depending on the signal being input.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 34 Correcting keystone distortion Keystone distortion is corrected automatically when the projector’s automatic setup function is used, but this correction will not apply if the screen itself is tilted. In such cases, you can correct the keystone distortion manually with the following procedure. Vertical keystone distortion correction only. KEYSTONE 0 Vertical keystone distortion correction Operation Press the H button. Press the I button.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 35 Adjusting the picture When an RGB signal is being input PICTURE PICTURE MODE DYNAMIC CONTRAST 32 BRIGHT 32 SHARPNESS 0 COLOR TEMP. STANDARD W-BAL R 32 W-BAL G 32 W-BAL B 32 AI ON SIGNAL MODE XGA STANDARD SELECT ADJ RETRN When an YPBPR signal is being input PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 2 COLOR TEMP.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 36 BRIGHT AI This adjusts the darker areas (black areas) in the picture. Black areas are too light: I button Dark areas are too solid: H button AI COLOR (S-VIDEO/VIDEO/YPBPR only) The colour is too deep: I button The colour is too pale: H button TINT (NTSC/NTSC 4.43/YPBPR only) This adjusts the flesh tones in the picture.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 37 STILL MODE STILL MODE OFF [ ON To reduce flickering of still images (vertical flicker), set “STILL MODE” to “ON”. NOTE: B Do not set “STILL MODE” to “ON” when playing back moving images. SIGNAL MODE (RGB/YPBPR only) This displays the type of signal which is currently being projected. Refer to the table on page 58 for details on each type of signal.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 38 Adjusting the position When an RGB signal is being input, press the AUTO SETUP button first to initiate automatic positioning. If the optimum setting is not obtained when “AUTO SETUP” is carried out, adjust by the following procedure. Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting.
p020-039(PT-LM2E)en 04.12.25 9:28 ページ 39 ASPECT (S-VIDEO/VIDEO/525i, 525p, 625i and 625p YPBPR signals only) ASPECT AUTO [ S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen.) 4:3 [ 16:9 [ S4:3 When a 4:3 signal is being input. [ When using the 16:9 screen When a horizontally squeezed signal is being input.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 40 NOTE: B If a selected mode does not match the aspect ratio of the input signal, it may affect the quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 41 Changing the display language Press the F or G button on the projector or remote control unit to select a language, then press the ENTER button to accept the setting. SELECT ENTER ENGLISH Indicates the language which is currently set.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 42 Option settings Press the F or G button on the projector or remote control unit to select an item, then press the I or H button to change the setting. OPTION1 OSD ON AUTO SIGNAL ON AUTO KEYSTN ON AUTO RGB/YPB PR VGA60/525P VGA60 SXGA MODE SXGA NR OFF SELECT ADJ RETRN OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 100H FUNC 1 INDEX CONTROL KEY ON AUTO POW.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 43 VGA60/525P 525P [ VGA60 When a VGA60 or 525p RGB signal is being input, select the signal in accordance with the input signal. SXGA MODE SXGA MODE SXGA [ SXGA+ This setting is only for an SXGA signal. SXGA Select this item normally. SXGA+ When the edges of the projected image are not visible, select this item. Noise Reduction (NR) (S-VIDEO/VIDEO only) NR OFF [ ON If noise occurs from the projector because of a poor input signal, set “NR” to “ON”.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 44 projector in small rooms where high luminance is not required, it is recommended that you set the “LAMP POWER” to “LOW”. NOTE: B “LAMP POWER” cannot be set when no signal is being input. LAMP RUNTIME This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 51, and reset “LAMP RUNTIME” to “0”.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 45 Setting up the security function This projector is equipped with a security function. A password input screen can be displayed, or a company URL can be set up and displayed at the bottom of the projected image. Press the F or G button on the projector or remote control unit to select “SECURITY”, then press the ENTER button.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 46 NOTE: B The entered password will appear as . It will not be displayed on the screen. B If you enter the wrong password, the letters “PASSWORD” and “NEW” will become red. Enter the correct password again. TEXT DISPLAY The setup letters can be displayed at the bottom of the projected image while an image is projected. ON “TEXT DISPLAY” is enabled. OFF “TEXT DISPLAY” is disabled.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 47 When the TEMP indicator and the LAMP indicator are illuminated There are two indicators on the control panel of the projector which give information about the operating condition of the projector. These indicators illuminate or flash to warn you about problems that have occurred inside the projector, so if you notice that one of the indicators is on, turn off the power and check the table below for the cause of the problem.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 48 LAMP indicator Indicator display Illuminated (red) It is nearly time to Problem replace the lamp unit. Flashing (red) An abnormality has been detected in the lamp circuit. B Does “REPLACE B The power may B There may be an LAMP” appear on have been turned abnormality in the Possible the screen after on straight away lamp circuit. cause the projector is after it was turned turned on? off.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 49 Cleaning and replacing the air filter If the air filter becomes clogged with dust, the internal temperature of the projector will rise, the TEMP indicator will flash and the projector power will turn off. The air filter should be cleaned every 100 hours of use. Cleaning Replacement procedure Use a vacuum cleaner to clean off any accumulated dust. # Turn off the power and disconnect the mains lead.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 50 Replacing the lamp unit Warning When replacing the lamp, allow it to cool for at least one hour before handling it. B The lamp cover gets very hot, and contact with it can cause burns. Notes on replacing the lamp unit B The light generating lamp is made of glass, so dropping it or allowing it to hit hard objects may cause it to burst. Be careful when handling the lamp.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 51 On-screen display LAMP indicator Displayed for 30 seconds. Pressing any More than 1 800 hours button will clear the display. More than 2 000 hours Illuminates red during image projection and standby mode. Remains displayed until any button is pressed.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 52 ' Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screws. NOTE: B Be sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on. ( Connect the mains lead. ) Press the POWER button so that a picture is projected onto the screen.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 53 Before calling for service Before calling for service, check the following points. Page – – 47 48 – – 23 36 27 – 23 18 – 18 36 – – 28, 31 – 21 21 21 44 ENGLISH-53 Care and maintenance Problem Possible cause Power does not B The mains lead may not be connected. turn on. B The main power supply is not being supplied to the mains socket. B TEMP indicator is illuminated or flashing. B LAMP indicator is illuminated or flashing.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 54 Problem Possible cause Page The picture does B The signal format (“TV-SYSTEM”) may not be set 36 not display correctly. correctly. – B There may be a problem with the video tape or other signal source. B A signal which is not compatible with the projector 58 may be being input. Picture from B The cable may be too long. – computer does B The external video output for the laptop computer – not appear. may not be set correctly.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 55 Cleaning and maintenance Before carrying out cleaning and maintenance, be sure to disconnect the mains plug from the mains socket. Care and maintenance Wipe the cabinet with a soft, dry cloth. If the cabinet is particularly dirty, soak the cloth in water with a small amount of neutral detergent in it, squeeze the cloth very well, and then wipe the cabinet. After cleaning, wipe the cabinet dry with a dry cloth.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 56 Specifications Power supply: Power consumption: Amps: LCD panel: Panel size (diagonal): Aspect ratio: Display method: Drive method: Pixels: Lens: 100 V – 240 V ~, 50 Hz/60 Hz 180 W [During standby (when fan is stopped): Approx. 5 W] 2.2 A – 1.0 A 0.55 type (13.97 mm) 4:3 3 transparent LCD panels (RGB) Active matrix method 480 000 (800 x 600) x 3 panels Manual zoom (1 - 1.2) / Manual focus F 1.8 - 1.9, f 17.0 mm - 20.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 57 S-VIDEO IN: AUDIO IN: Cabinet: Dimensions: Width: Height: Length: Weight: Operating environment: Temperature: Humidity: Certifications: Power supply: Operating range: Weight: Dimensions: Width: Length: Height: Ceiling bracket Wireless remote control unit Single-line, RCA pin jack 1.0 V [p-p], 75 Ω Single-line, Mini DIN 4-pin Y 1.0 V [p-p], C 0.286 V [p-p], 75 Ω Single-line, RCA pin jack x 2 (L-R) 0.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 58 Appendix List of compatible signals Display resolution (dots)*1 Mode NTSC/NTSC4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 525i 625i 525p 625p HDTV60 HDTV50 750p VGA400 VGA480 *4 SVGA *4 MAC16 XGA *4 MXGA MAC21 MSXGA SXGA *3 *4 720 x 480i 15.734 59.
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 59 Connector pin wiring B The pin layout and signal names for the S-VIDEO IN connector are shown below. Pin No. Signal # $ Earth (Luminance signal) # Earth (Colour signal) $ Luminance signal % % & External view Colour signal & B The pin layout and signal names for the RGB IN connector are shown below. Pin No. Signal 1 R/PR # G/G·SYNC/Y $ ( , B/PB % SDA . # ' HD/SYNC / VD 0 External view SCL 1 Pin & and + are spare. Pins ' – *, , and - are for earth. Pins .
p040-060(PT-LM2E)en 04.12.25 9:28 ページ 60 Dimensions 63.5(2-1/2) 257(10-3/32) 69(2-11/16) 10(-3/8) 40(1-9/16) 209 (8-7/32) Trademark acknowledgements B VGA and XGA are trademarks of International Business Machines Corporation. B Macintosh is a registered trademark of Apple Computer, Inc. B S-VGA is a registered trademark of the Video Electronics Standards Association. All other trademarks are the property of the various trademark owners.
