Operating Instructions Projector Operations LCD Projector Model No. Commercial Use PT-VW330E PT-VX400E Thank you for purchasing this Panasonic Product. JJ Before operating this product, please read the instructions carefully and save this manual for future use. For information on using the product via a network, refer to “Operating Instructions – Network Operations”.
Read Read thisthis first! first! Important Information WARNING: THIS APPARATUS MUST BE EARTHED. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. WARNING: 1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time. 2.
WARNING: POWER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately. Continued use of the projector in these conditions will result in fire or electric shock. zz If foreign objects or water get inside the projector, cut off the power supply. zz If the projector is dropped or the cabinet is broken, cut off the power supply.
Read this first! Important Information WARNING: Installation work (such as ceiling mount bracket) should only be carried out by a qualified technician. If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks. zz Do not use anything other than an authorized ceiling mount bracket. zz Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the projector from falling down.
WARNING: ACCESSORIES Do not use or handle the batteries improperly, and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire. zz Do not use unspecified batteries. zz Do not disassemble dry cell batteries. zz Do not heat the batteries or place them into water or fire. zz Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins.
Read this first! Important Information CAUTION: ON USE/INSTALLATION Do not put your weight on this projector. You could fall or the projector could break, and injury will result. zz Be especially careful not to let young children stand or sit on the projector. Do not place the projector in extremely hot locations. Doing so will cause the outer casing or internal components to deteriorate, or result in fire. zz Take particular care in locations exposed to direct sunlight or near stoves.
Auto Setup Function This function enables Input search, Auto Keystone correction and Auto PC adjustment by pressing the button. Direct Power Off Function With the Direct Power Off function, you can disconnect the power cord from the wall outlet or turn off the breaker even during projection. Improved connectivity The inclusion of an HDMI terminal provides support for high quality video and HDMI audio.
Contents Be sure to read “Read this first!”. ( Important Information Important Information Read this first!............................................ 2 Precautions for Use................................. 10 Preparation Cautions when transporting........................................... 10 Cautions when installing................................................ 10 Security..........................................................................11 Disposal...........................................
Sound........................................................ 49 Volume.......................................................................... 49 Mute.............................................................................. 49 MIC. ............................................................................... 49 MIC gain........................................................................ 49 Standby MIC out............................................................
Precautions for Use Important Information Cautions when transporting zz When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. Doing so may damage the internal parts and result in malfunctions. zz Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet. Cautions when installing JJ Do not set up the projector outdoors. zz The projector is designed for indoor use only.
Precautions for Use Important Information JJ Cautions when setting the projectors zz Do not stack the projectors. zz Do not block the ventilation ports (intake and exhaust) of the projector. zz Avoid heating and cooling air from the air conditioning system directly blow to the ventilation ports (intake and exhaust) of the projector. over 1 m (40") over 50 cm (20") over 1 m (40") over 20 cm (7.8") zz Do not place the projector in an enclosed space.
Precautions for Use Important Information Cautions on use JJ In order to get the picture quality zz Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. zz Depending on where the projector is used, heated air from an exhaust port or warm or cold air from an air conditioner can cause a shimmering effect on screen.
Accessories Make sure the following accessories are provided with your projector. Numbers in the brackets ( ) show the number of accessories.
Precautions for Use Important Information JJ Contents of the supplied CD-ROM The contents of the supplied CD-ROM are as follow. Operating Instructions – Projector Operations. Operating Instructions – Network Operations. [: Instructions/List (PDF), : Software] Multi Projector Monitoring & Control Software 2.6(Windows) •• This software allows you to monitor and control multiple projectors connected to the LAN. Operation Manual Multi Projector Monitoring & Control Software 2.
About Your Projector (18) (1) (10) (2) (3) (4) (11) (5) (12) (6) (13) (14) (7) (15)* (16) (17) (8) (9) Buttons (+/-) Adjusts the volume of the speaker. (Æpage 32) (10) Button Turn the projector on or off. (Æpage 26) (11) Button Correct keystone distortion. (Æpage 31) (12) Button Operate the information function. (Æpage 31) (13) Button Select a lamp mode. (Æpage 32) (14) Button Operate the P-timer function.
About Your Projector Projector body (6) Preparation (1)(2) (3)(4) (7) (5) (9) (10) (11) (8) (12) (12) ■ Bottom view (13) (1) Remote control signal receiver (2) Focus Ring Adjusts the focus. (3) Projection Lens (4) Zoom Lever Adjusts the zoom. (5) Air intake port (6) Control Panel and Indicators(Æpage 17) (7) Lamp cover (Æpage 63) The lamp unit is located inside. (8) Air outlet port •• Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side.
About Your Projector (9) (5) (8) (4) (7) (3) (2) (1) (6) (1)
Using Remote Using Remote control control Installing and Removing batteries 1111 Open the cover 2222 Install batteries and close the cover (Insert the – side first.) Preparation zz Remove the batteries in the reverse order of installation. Setting Remote control ID numbers When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if unique ID number is assigned to each projector.
Setting up Projection method You can use the projector with any of the following 4 projection methods. To set the desired method in the projector.
Setting up Screen size and throw distance Place the projector referring to the diagram on the right and the figures of throwing distance.
Setting up JJProjection distance for PT-VX400E (All measurements below are approximate and may differ slightly from the actual measurements.) For 4:3 aspect ratio For 16:9 aspect ratio Screen diagonal (SD) Minimum distance (LW) Maximum distance (LT) Minimum distance (LW) Maximum distance (LT) 0.76 m(30") 0.7 m(2.26') 1.1 m(3.74') 0.8 m(2.49') 1.2 m(4.07') 1.02 m(40") 0.9 m(3.05') 1.5 m(5.02') 1.0 m(3.35') 1.7 m(5.48') 1.27 m(50") 1.2 m(3.87') 1.9 m(6.30') 1.3 m(4.23') 2.1 m(6.89') 1.
Setting up Adjusting front adjustable feet Lift the front of the projector and press the feet lock latches on both side of the projector. Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to a proper height and tilt. You can turn the front adjustable feet to extend them. You can turn them in the opposite direction to contract them. (You can adjust the projection angle vertically.
Connections Before connecting to the projector zz Read carefully the instruction manual for the device to be connected. zz Turn off the power switch of the devices before connecting cables. zz If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, prepare a necessary system connection cable to suit the device. zz Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture.
Basic Operation Powering ON/OFF Connecting the power cord Be sure to insert the attached power cord securely to its base to prevent it from coming off. JJPower cord holder A power cord holder is designed to prevent the AC power cord from coming off the projector. Please insert the power cord into the power cord holder correctly as Picture (1) shown: Clamp AC Power cord holder Picture (1) JJAttaching Attach the AC power cord with the power cord clamp to the projector by following these steps.
Powering ON/OFF Power indicator The power indicator informs you the status of the power. Confirm the status of the before operating the projector. Power indicator Indicator status Lit RED Flashing GREEN Lit Flashing The power cord is unplugged. Press the ON/STAND-BY ( ) button to start the projection. The temperature inside the projector is abnormally high. The projector cannot be turned on until cooling is completing and the POWER indicator stops blinking. Projecting.
Powering ON/OFF Turning On the Projector (3) (3) (2) 1111 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. 06 2222 Connect the projector’s AC power cord into an AC outlet. The POWER indicator lights red. Open the lens cap. Basic Operation 3333 Press the button to on the control panel or on the remote control. The POWER indicator lights green and the cooling fans start to operate.
Powering ON/OFF Enter a PIN code Press ▲▼ to enter a number. Press ► to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to “Set”. Press the
Powering ON/OFF Turning Off the Projector 1111 Press the button on the top control or on the remote control, and Power off? appears on the screen. 2222 Press the button again to turn off the projector. The POWER indicator starts to blink red, and the cooling fans keep running. At this time, you can unplug the AC power cord even if the fans are still running. 3333 When the projector has cooled down enough, the POWER indicator stops blinking and you can turn on the projector.
Projecting Check the connections of the peripheral devices and connection of the power cord (Æpage 24) and switch on the power (Æpage 26) to start the projector. Select the image and adjust the state of the image. Selecting the image Select an input signal. The image selected with the , , ,
Basic operations by using the remote control COMPUTER 1 Switches to Computer 1(RGB)/ Computer 1(Scart) input. COMPUTER 2 Switches to Computer 2(RGB) input. HDMI Switches to HDMI input. VIDEO Switches to Video input. S-VIDEO COMPONENT Switches to S-video input. Switches to Computer 1 (Component) input. Note zz Each press of the button on the Control Panel of the main unit switches the settings as shown below.
Basic operations by using the remote control Using the KEYSTONE button This function allows you to correct keystone distortion. Using the INFO. button This function allows you to display the information menu. button button If a projected picture still has keystone distortion after pressing the button, correct the image manually as follows: Press the button on the remote control. The Keystone dialog box appears. Press ▲▼ to correct keystone distortion.
Basic operations by using the remote control Using the AV MUTE function button Using the D.ZOOM buttons This function allows you to enter to the Digital zoom +/– mode. Press the < AV MUTE> button on the remote control to black out the image. To restore to normal, press the < AV MUTE> button again or press any button. black out→ normal...... Note zz When use the button to release the AV MUTE function, the mute function can not be operated at the same time.
Basic operations by using the remote control Using the P IN P button (PT-VW330E Only) This function allows you to operate the Picture In Picture function. button Press
button on the remote control. Note zz For details, see “P IN P” of "Setting" under Main menu. (Æpage 52) Using the MUTE button Press this button on the remote control to select On to temporarily turn off the sound. Basic Operation button Press button on the remote control.
Menu Navigation Navigating through the menu JJOperating procedure 3333 Press ► or the
Menu Navigation Sub menu The main menu consists of the following 9 menu items. When a main menu item is selected, the screen changes to a submenu selection screen. The sub-menu screen of the selected main menu appears, and you can set and adjust the various items in the submenu.
Menu Navigation Image adjust [ JJSetting [ ] Sub-menu item Contrast Brightness Color*1 Tint*1 Color temp. Red Green Blue Sharpness Gamma Noise reduction*1 Progressive*1 Reset Store Factory default 32 32 32 32 Mid 32 32 32 8 8 L1 L1 - Page 43 43 43 43 43 44 44 44 44 44 44 45 45 45 ***** When input video signal to the projector, these functions will be available. JJScreen [ ] Settings Sub-menu item Normal Full Wide (16:9) Zoom True*1 Natural wide*2 Custom Custom adj.
Input menu Select [Input] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel ---- There is no signal input from the computer. Check the connection between your computer and the projector. Mode 1 The preset system is manually adjusted in the PC adjust Menu. The adjusted data can be stored in Mode 1-10. SVGA 1 PC Systems provided in this projector is chosen.
Input menu PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M and PAL-N. Component Auto The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance. COMPONENT VIDEO SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i and 1080i.
AUTO PC adjust AUTO PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel AUTO PC adj. Auto PC adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical positions to conform to your computer. Press ▲▼ to select [AUTO PC adj.] and then press the
Manual PC adjust Manual PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Horizontal 1111 Press ▲▼ to select [Horizontal]. 2222 Press the
Manual PC adjust Current mode 1111 Press ▲▼ to select [Current mode]. 2222 Press ► or the
Image select Select [Image select] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Blackboard(Green) For the image projected on a blackboard. Press ▲▼ to select [Blackboard(Green)] and then press the
Image adjust Image adjust Select [Image adjust] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Control Panel Remote Control Color 1111 Press ▲▼ to select [Color]. 2222 Press the
Image adjust Red Sharpness 1111 Press ▲▼ to select [Red]. 2222 Press the
Image adjust Progressive 1111 Press ▲▼ to select [Progressive]. 2222 Press the
Screen Screen Select [Screen] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel True Provide the image in its original size. When the original image size is larger or smaller than the screen size (1280 x 800),* the projector enters to the panning mode automatically. 1111 Press ▲▼ to select [True] and then press the
Screen Custom adj. Adjust the screen scale and position manually with this function. 1111 Press ▲▼ to select [Custom adj.]. 2222 Press ► or the
Screen Ceiling Reset This function is used to project the image from a ceiling-mounted projector. 1111 Press ▲▼ to select [Ceiling] and then press the
Sound Sound Select [Sound] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel MIC 1111 Press ▲▼ to select [MIC] and then Press the
Setting Setting Select [Setting] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Menu position This function is used to change the position of the OnScreen Menu. 1111 Press ▲▼ to select [Menu position]. 2222 Press the
Setting Auto Always works and corrects keystone distortion according to the projector's tilt. Manual Works only when pressing the button on the remote control or the button on the control panel. Off Disables Auto Keystone. Note zz Input search, Auto PC adj. and Auto Keystone cannot be set Off at the same time. zz The Auto Keystone function cannot work when the Ceiling feature is set On in the Setting menu.
Setting JJLogo PIN code change Logo PIN code can be changed to your desired fourdigit number. 1111 Press ▲▼ to select [Logo PIN code change]. 2222 Press the
Setting JJSubpicture size JJTimer 1111 Press ▲▼ to select [Subpicture size] and then press the
Setting 2222 Press ► or
Setting This function allows you to change brightness of the screen. 1111 Press ▲▼ to select [Lamp power] and then press the
Setting JJPIN code change The PIN code can be changed to your desired fourdigit number. 1111 Press ▲▼ to select [PIN code change] and then Press
Setting 2222 Press ▲▼ to set the Timer. zz Select from (Off/1000H/2000H/3000H/40 00H/5000H/6000H) depending on the use environment. JJFilter counter reset After replacing the filter, be sure to reset the timer. 1111 Press ▲▼ to select [Filter counter reset]. 2222 Press the
Information Information Select [Information] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel JJLamp power The selected lamp mode is displayed. JJLamp runtime The cumulative lamp operating time is displayed. JJPower management Off , Ready or Shut down, and timer are displayed. JJKey lock The selected Key lock icon is displayed.
LAMP REPLACE and WARNING Indicators LAMP REPLACE and WARNING Indicators Managing the indicated problems If a problem should occur inside the projector, the POWER, LAMP REPLACE and/or WARNING indicators will inform you. Manage the indicated problems as follow. CAUTION zz Before you take a remedial measure, follow the procedure of switching the power off indicated in “Turning off the projector”.
Replacement Before replacing the unit zz When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect the power plug from the wall outlet. (Æpages 24, 28) zz Be sure to observe the procedure “Turing off the projector” (Æpage 28) when performing power supply operation. Maintenance JJOuter Case Wipe off dirt and dust using a soft dry cloth. zz If the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping.
Replacement cover (side); pull out the handle and take out the side filter. 2222 Replace the air filter units. zz Put new filters back into the position. Make sure that the filters are fully inserted to the projector. JJ Resetting the Filter Counter Be sure to reset the Filter counter after replacing the filter.(Æpage 57" Filter counter reset") Attention zz Turn off the power before you replace the air filter unit.
Replacement CAUTION: ■ Do not replace the lamp unit when it is hot. (Wait at least 45 minutes after use.) The inside of the cover can become very hot, take care to avoid burn injuries. JJNotes on the replacement of the lamp unit zz The luminous source of the lamp is made of glass and may burst if you hit it against a hard surface or drop it. Please handle with care. zz A Phillips screwdriver is required for replacement of the lamp unit. zz When replacing the lamp unit, be sure to hold it by the handle.
Replacement JJ Replacing the Lamp unit CAUTION: zz When the projector is mounted on a ceiling, do not work with your face close to the projector. zz Attach the lamp unit and the lamp cover securely. zz When you experience difficulty in installing the lamp, remove it and try again. If you use force to install the lamp, the connector may be damaged. Lamp cover 1111 Turn off the Power by following the procedure in “Turning off the projector (Æpage 28). Unplug the AC power cord.
Replacement Attaching the Lens Cap When moving this projector or while not using it over an extended period of time, attach the lens cap. Attach the lens cap according to the following procedures. 1111 Thread the string through the hole on the lens cap and then tie a knot in the string to secure it in place. 2222 To pass the other end of the string into the hole on the bottom of the projector and pull at it.
Troubleshooting Please check following points. For details, see the corresponding pages. Reference page Cause zz The power cord may not be connected. — zz No electric supply is at the wall outlet. — Power does not turn zz The circuit breakers have tripped. on. zz Is the , , or lit or blinking? 25, 59 zz The lamp cover has not been securely installed.
Troubleshooting Problem Picture from a HDMI device does not appear or picture is not stable. No sound is output from a HDMI device. Cause zz Is the HDMI cable securely connected? 23 zz Turn off the power of the projector and the connected devices. Then turn — zz Isn't unsupported signal cable connected? 72 zz Set the sound channel of the attached device to Linear PCM.
Technical Information Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connector. JJConnection Connecting terminals on projector Computer D-Sub 9-pin (male) D-Sub 9-pin (female) Communication cable JJPin assignments and signal names D-Sub 9-pin (male) Outside view Pin No.
Technical Information JJBasic format Transmission from the computer begins with STX, then the command, parameter, and ETX are sent in this order. Add parameters according to the details of control. STX C1 C2 C3 P1 Colon (1 byte) 3 command characters (3 bytes) Start (1 byte) : P2 Pn Parameter (undefined length) ETX End (1 byte) ½½½ When sending commands without parameters, a colon (:) is not necessary.
Technical Information JJCable specifications [When connected to a computer] Projector 1 2 3 4 5 6 7 8 9 NC NC NC NC 1 2 3 4 5 6 7 8 9 Computer (DTE specifications) JJControl commands When controlling the projector from a computer, the following commands are available: [Projector control command] Control contents PON Power [ON] POF Power [OFF] AUU Volume + AUD Volume - Remarks (Parameter) 000 (adjustment value 0) to 063 (adjustment value 63) INPUT selection (Parameter) VID = VIDEO SVD =
Technical Information Other terminals JJPin assignments and signal names of terminal Pin No. Outside view Signal names GND (luminance signal) GND (color signal) Luminance signal Color signal JJPin assignments and signal names of terminal Pin No. Outside view Signal names R/PR G/G SYNC/Y B/PB +5V DDC data HD/SYNC VD DDC clock : Not assigned - , , : GND terminals JJPin assignments and signal names of terminal Pin No.
Technical Information Two window display combination list (PT-VW330E Only) Sub Window Computer 1 Main Window RGB Computer 1 Component Computer 2 RGB(Scart) RGB HDMI Video S-video HDMI Video S-video RGB Component RGB(Scart) Computer 2 RGB HDMI HDMI Video Video S-video S-video o : Picture in Picture combinations are enabled. x : Picture in Picture combinations are disabled Note zz When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture.
Technical Information List of compatible signals The following table specifies the types of signals compatible with the projectors. Format : V = VIDEO, S = S-VIDEO, C = COMPUTER, Y = YPBPR, H = HDMI Mode Display resolution *1 (dots) Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) 480p 640 x 480 31.47 59.88 25.2 480i 640 x 480i 15.734 60.00 12.2727 Picture quality *2 PnP PTVW330E PTVX400E A A Format COMPUTER HDMI 576p 768 x 576 31.25 50.00 29.
Technical Information 1024 x 768 XGA 1024 x 768i 1152 x 864 1152 x 900 1280 x 960 SXGA 1280 x 1024 1280 x 1024i Scanning frequency Dot clock frequency (MHz) Picture quality *2 PnP H (kHz) V (Hz) PTVW330E PTVX400E 48.36 60.00 65.00 A AA 68.677 84.977 94.504 A 60.023 75.03 78.75 56.476 70.07 75.00 60.31 74.92 48.50 60.02 44.00 63.48 Format COMPUTER HDMI AA ○ ○ A AA ○ ○ A AA ○ ○ 79.252 A AA 65.179 A AA 54.58 59.129 A AA 79.35 83.41 A AA 62.04 77.
Technical Information Mode D-SXGA+3 UXGA H (kHz) V (Hz) 1400 x 1050 65.120 59.900 122.430 75.00 60.00 162.00 81.25 65.00 175.50 87.5 70.00 93.75 1600 x 1200 1280 x 768 WXGA Scanning frequency Display resolution *1 (dots) 1280 x 800 1366 x 768 1360 x 768 Dot clock frequency (MHz) Picture quality *2 PnP PTVX400E COMPUTER A A ○ 189.00 AA A ○ 75.00 202.50 AA A 47.776 59.870 79.500 AA A 60.289 74.893 102.250 AA A 68.633 84.837 117.500 49.600 60.050 79.
Technical Information Mode Display resolution *1 (dots) Scanning frequency Dot clock frequency (MHz) H (kHz) V (Hz) 63.98 60.02 108 60.276 58.069 93.067 D-SXGA 1280 x 1024 31.65 29.8 53.48 D-1035i 1920 x 1035i 33.75 60.00 74.25 D-1080/50i 1920 x 1080i 28.125 50.00 74.25 D-1080/60i 1920 x 1080i 33.75 60.00 74.25 D-1080p 1920 x 1080 67.5 60.00 148.5 56.25 50.00 148.5 D-WXGA+1 1440 x 900 55.935 59.887 106.500 D-WSXGA+1 1680 x 1050 65.290 59.954 146.
Specifications Model No. PT-VW330E Power supply PT-VX400E AC100 V - 240 V 50 Hz/60 Hz 100 V - 240 V 3.8 A-1.8 A 322 W When [Standby mode] of [Setting] is set to [ECO]: 0.48W Power consumption When [Standby mode] of [Setting] is set to [Network]: 12.5W When [Standby mode] of [Setting] is set to [Network]: 10.0W When [Standby MIC out] of [Sound] is set to [On]: Max.26 W Panel size LCD panel 1.5 cm(0.
Specifications Model No. COMPUTER IN 1/ COMPONENT IN COMPUTER IN 2/ MONITOR OUT Terminals VIDEO IN S-VIDEO IN HDMI IN AUDIO IN AUDIO OUT CONTROL PORT LAN PT-VW330E PT-VX400E 1 (D-sub 15 pin female) [RGB signal] 0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 [p-p] 75 Ω HD/SYNC TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible [YPBPR signal] Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω RGB signal] 0.
Ceiling mount bracket safeguards Specifications Dimensions 254.4（10.0"） 97.0（3.82"） 9.5（0.38"） 52.3（2.06"） 87.5（3.44"） 3.8（0.15"） 350.0（13.78"） 81.03 (3.19") ½½½ Actual dimension may differ by product. Ceiling mount bracket safeguards zz Installation work of the ceiling mount bracket should only be carried by a qualified technician.
Index About Your Projector.......................15 Accessories.....................................13 Adjusting front adjustable feet.........22 Attaching the Lens Cap...................64 AUTO PC adjust..............................39 Auto setup.......................................50 AV MUTE.........................................32 B Background.....................................51 Basic operations by using the remote control..........................................30 Blackboard(Green)............
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
