Operating Instructions Projector Operations LCD Projector Model No. Commercial Use PT-TW230E Thank you for purchasing this Panasonic Product. JJ Before operating this product, please read the instructions carefully and save this manual for future use. For information on using the product via a network, refer to “Operating Instructions – Network Operations”.
Read this first! Important Information WARNING: THIS APPARATUS MUST BE EARTHED. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. WARNING: 1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time. 2.
WARNING: POWER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately. Continued use of the projector in these conditions will result in fire or electric shock. zz If foreign objects or water get inside the projector, cut off the power supply. zz If the projector is dropped or the cabinet is broken, cut off the power supply.
Read this first! Important Information WARNING: Installation work (such as ceiling mount bracket) should only be carried out by a qualified technician. If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks. zz Do not use anything other than an authorized ceiling mount bracket. zz Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the projector from falling down.
WARNING: ACCESSORIES Do not use or handle the batteries improperly, and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire. zz Do not use unspecified batteries. zz Do not disassemble dry cell batteries. zz Do not heat the batteries or place them into water or fire. zz Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins.
Read this first! Important Information CAUTION: ON USE/INSTALLATION Do not put your weight on this projector. You could fall or the projector could break, and injury will result. zz Be especially careful not to let young children stand or sit on the projector. Do not place the projector in extremely hot locations. Doing so will cause the outer casing or internal components to deteriorate, or result in fire. zz Take particular care in locations exposed to direct sunlight or near stoves.
Auto Setup Function This function enables Input search and Auto PC adj. by pressing the button on the remote control. Direct Power Off Function With the Direct Power Off function, you can disconnect the power cord from the wall outlet or turn off the breaker even during projection. Improved connectivity JJQuick steps For details, see the corresponding pages. 1. Set up your projector. (Æpage 19) 2. Connect with other devices. (Æpage 22) 3. Connect the power cord.
Contents Be sure to read “Read this first!”. ( Important Information Important Information Read this first!............................................ 2 Contents...................................................... 8 Precautions for Use................................. 10 Preparation Cautions when transporting........................................... 10 Cautions when installing................................................ 10 Security...............................................................
Normal........................................................................... 44 Full. ............................................................................... 44 Wide(16:9)..................................................................... 44 Zoom............................................................................. 44 True................................................................................ 44 Natural wide .................................................................
Precautions for Use Important Information Cautions when transporting zz When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. Doing so may damage the internal parts and result in malfunctions. zz Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet. Cautions when installing JJ Do not set up the projector outdoors. zz The projector is designed for indoor use only.
Precautions for Use zz Do not stack the projectors. zz Do not block the ventilation ports (intake and exhaust) of the projector. zz Avoid heating and cooling air from the air conditioning system directly blow to the ventilation ports (intake and exhaust) of the projector. zz You can tile the projector within ± 20 degrees Important Information JJ Cautions when setting the projectors + 20° _ 20° horizontally. over 50 cm (20") over 50 cm (20") over 1 m (40") over 20 cm (7.
Precautions for Use Important Information Cautions on use JJ In order to get the picture quality zz Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. zz Depending on where the projector is used, heated air from an exhaust port or warm or cold air from an air conditioner can cause a shimmering effect on screen.
Accessories Make sure the following accessories are provided with your projector. Numbers in the brackets ( ) show the number of accessories.
Precautions for Use Important Information JJ Contents of the supplied CD-ROM The contents of the supplied CD-ROM are as follow. Operating Instructions – Projector Operations Operating Instructions – Network Operations. [: Instructions/List (PDF), : Software] Multi Projector Monitoring & Control Software 2.6(Windows) •• This software allows you to monitor and control multiple projectors connected to the LAN. Operation Manual Multi Projector Monitoring & Control Software 2.
About Your Projector Remote control (17) (10) (2) (3) (4) (11) (5) (12) (6) (13) (14) (7) (8) (15) (16) (9) (10) < >Button Turn the projector on or off. (Æpage 25) (11) Button Correct keystone distortion. (Æpage 30) (12) Button Operate the information function. (Æpage 30) (13) Button Select a lamp mode. (Æpage 31) (14) Button Operate the P-timer function. (Æpage 31) (15) Button Select the image mode. (Æpage 30) (16) Button Mute the sound.
About Your Projector Projector body (2) (1) Preparation (3) (4) (7) (6) (5) � (8) (9) Bottom View (10) (11) (12) (13) (1) Control panel (Æpage 17) (12) AC IN (2) Lamp cover (Æpage 61) The lamp unit is located inside. (3) Remote control signal receiver (13) Adjustable feet Adjusts the projection angle. (4) Projection Lens WARNING: zz Keep your hands and other objects away from the (5) Speaker (6) Air outlet port •• Hot air is exhausted from the exhaust vent.
About Your Projector Control panel (1) (3) (1) < >button Turn the projector on/off. (2) ▲▼◄► (VOL -/+) buttons (4) (2) Navigate the MENU screen. Execute the selected item. (4)
Using Remote control Installing and Removing batteries 1111 Open the cover 2222 Install batteries and close the cover (Insert the – side first.) Preparation zz Remove the batteries in the reverse order of installation. Setting Remote control ID numbers When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if unique ID number is assigned to each projector.
Setting up Projection method You can use the projector with any of the following 4 projection methods. To set the desired method in the projector.
Setting up Screen size and throw distance Place the projector referring to the diagram on the right and the figures of throwing distance. You can adjust the display size. SH Projected image SH SD Screen L SW L Projection distance (m) Height of the projection area (m) SW Width of the projection area (m) SD Diagonal length of the projection area (m) SW SH L Screen Getting Started Attention zz Before installing, please read “Precautions for Use” (Æ pages 10 to 14).
Setting up Adjusting front adjustable feet Projection angle can be adjusted up to 10.0 degrees with the adjustable feet. Rotate the adjustable feet and tilt the projector to the proper height; to raise the projector, rotate the both feet clockwise. To lower the projector or to retract the adjustable feet, rotate the both feet counterclockwise. (You can adjust the projection angle vertically.) Adjustable Feet Adjustable range Front adjustable feet : 43.5 mm(1.
Connections Before connecting to the projector zz Read carefully the instruction manual for the device to be connected. zz Turn off the power switch of the devices before connecting cables. zz If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, prepare a necessary system connection cable to suit the device. zz Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture.
Basic Operation Powering ON/OFF Connecting the power cord Be sure to insert the attached power cord securely to its base to prevent it from coming off. JJPower cord holder A power cord holder is designed to prevent the AC power cord from coming off the projector. Please insert the power cord into the power cord holder correctly as Picture (1) shown: AC Power cord holder Clamp Picture (1) JJAttaching 1111 Plug the power cord with the power cord holder to the projector as Picture (2) shown.
Powering ON/OFF ON(G)/STANDBY(R) indicator The ON(G)/STANDBY(R) indicator informs you the status of the power. Confirm the status of the indicator before operating the projector. ON (G)/STANDBY(R) indicator Indicator status No illumination or flashing Lit Basic Operation Flashing 24 - ENGLISH The power cord is plugged. The projector is in stand-by mode, after the cooling is completed.
Powering ON/OFF Turning On the Projector (3) (3) (3) (2) 2222 Connect the projector’s AC power cord into an AC outlet. The indicator lights red. Open the lens cover. 3333 Press the < > button on the control panel or on the remote control. The indicator lights green and the cooling fans start to operate. The preparation display appears on the screen and the count down starts.
Powering ON/OFF Enter a PIN code Press ▲▼ to enter a number. Press ► to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to “Set”. Press the button so that you can start to operate the projector.
Powering ON/OFF Turning Off the Projector 1111 Press the < > button on the control panel or on the remote control, and Power off? appears on the screen. 2222 Press the < > button again to turn off the projector. The indicator starts to blink red, and the cooling fans keep running. At this time, you can unplug the AC power cord even if the fans are still running. Power off? disappears after 4 seconds.
Projecting Check the connections of the peripheral devices and connection of the power cord (Æpage 23) and switch on the power (Æpage 25) to start the projector. Select the image and adjust the state of the image. Selecting the image Select an input signal. The image selected with the , , ,
Basic operations by using the remote control COMPUTER 1 Switches to Computer 1(RGB)/ Computer 1(Scart) input. COMPUTER 2 Switches to Computer 2(RGB) input. HDMI Switches to HDMI input. VIDEO Switches to Video input. S-VIDEO COMPONENT Switches to S-video input. Switches to Computer 1 (Component) input. Note zz Each press of the button on the Control panel of the main unit switches the settings as shown below.
Basic operations by using the remote control Using the KEYSTONE button This function allows you to correct keystone distortion. button You can freeze the projected image and stop the sound temporarily, regardless of the playing condition of the connected device. button Press the button on the remote control or on the control panel. The Keystone dialog box appears. Press ▲▼ to correct keystone distortion. The keystone adjustment can be stored (Æpage 45).
Basic operations by using the remote control Using the AV MUTE function This function allows you to select the lamp mode for changing the brightness on the screen. button Press the button on the remote control to black out the image. To restore to normal, press the button again or press any button. zz When the Logo is not set, the screen changes each time you press the button as follows.
Menu Navigation Navigating through the menu JJOperating procedure 1111 Press the
Menu Navigation Sub menu The main menu consists of the following 9 menu items. When a main menu item is selected, the screen changes to a submenu selection screen. The sub-menu screen of the selected main menu appears, and you can set and adjust the various items in the submenu.
Menu Navigation JJImage adjust [ Sub-menu item Contrast Brightness Color*1 Tint*1 Color temp. Red Green Blue Sharpness Gamma Noise reduction*1 Progressive*1 Reset Store JJSetting [ ] Factory default 32 32 32 32 Mid 32 32 32 8 8 L1 L1 - Page 41 41 41 41 41 42 42 42 42 42 42 43 43 43 ***** When input video signal to the projector, these functions will be available. JJScreen [ ] Settings Sub-menu item Normal Full Wide (16:9) Zoom True *1 Natural wide *2 Custom Custom adj.
Input menu Select [Input] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel ---- There is no signal input from the computer. Check the connection between your computer and the projector. Mode 1 The preset system is manually adjusted in the PC adjust Menu. The adjusted data can be stored in Mode 1-10. SVGA 1 PC Systems provided in this projector is chosen.
Input menu PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among [PAL], [SECAM], [NTSC], [NTSC 4.43], [PAL-M] and [PAL-N]. Component Auto The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance.
AUTO PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel Auto PC adj. Auto PC adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical positions to conform to your computer. Press ▲▼ to select [Auto PC adj.] and then press the button. zz [Please wait...] appears while the Auto PC adjustment is in process.
Manual PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel Horizontal 1111 Press ▲▼ to select [Horizontal]. 2222 Press the button to display the adjustment dialog box. 3333 Press ◄► to adjust the horizontal picture position.
Manual PC adjust Current mode 1111 Press ▲▼ to select [Current mode]. 2222 Press ► or the button to enter the next submenu to show H-sync freq. and V-sync freq. of the connected computer. Clamp 1111 Press ▲▼ to select [Clamp]. 2222 Press the button to display the adjustment dialog box. 3333 Press ◄► to adjust the clamp level. zz When the image has dark bars, try this Reset To reset the adjusted data, all adjustments will return to their previous figures. 1111 Press ▲▼ to select [Reset].
Image select Select [Image select] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel Blackboard(Green) For the image projected on a blackboard. Press ▲▼ to select [Blackboard(Green)] and then press the button. zz This mode helps enhance the image projected on a blackboard. This is mainly effective on a green colored board, not truly effective on a black colored board.
Image adjust Select [Image adjust] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Control panel Remote control Color 1111 Press ▲▼ to select [Color]. 2222 Press the button to display the adjustment dialog box. 3333 Press ◄► to adjust the setting value. Operation Adjustment Adjustment range Press ►. increase the Maximum intensity of the color value 63 Press ◄.
Image adjust Red Sharpness 1111 Press ▲▼ to select [Red]. 2222 Press the button to display the adjustment dialog box. 3333 Press ◄► to adjust the setting value. Operation Adjustment Adjustment range Press ►. deepen red tone Maximum value 63 Press ◄. lighten red tone Minimum value 0 1111 Press ▲▼ to select [Sharpness]. 2222 Press the button to display the adjustment dialog box. 3333 Press ◄► to adjust the setting value. Operation Adjustment Adjustment range Press ►.
Image adjust Progressive 1111 Press ▲▼ to select [Progressive]. 2222 Press the button to display the dialog box. 3333 Press ◄► to select the desired item. zz An interlaced video signal can be displayed in progressive mode. Select one of the following options. zz [Progressive] cannot be selected when [480p], [576p], [720p], [1035i], [1080i] or [1080p] is selected.
Screen Select [Screen] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel True Provide the image in its original size. When the original image size is larger than the panel size (1280 x 800), the projector enters to the panning mode automatically. 1111 Press ▲▼ to select [True] and then press the button. 2222 Press ▲▼◄► to pan the image. zz When adjusted, the arrows will turn red.
Screen Custom adj. Adjust the screen scale and position manually with this function. 1111 Press ▲▼ to select [Custom adj.]. 2222 Press ► or the button to enter the next submenu. 3333 Press ▲▼ to choose the item you want to adjust. zz You can choose one from the items as below: Scale H/V Adjust the Horizontal/Vertical screen scale. H&V When set to [On], the aspect ratio is fixed. Position H/V Adjust the Horizontal/Vertical screen position.
Screen Ceiling Reset This function is used to project the image from a ceiling-mounted projector. 1111 Press ▲▼ to select [Ceiling] and then press the button. 2222 Press ▲▼ to change the image. zz When this function is set to [On], the picture will be top/bottom and left/right reversed. Rear This function is used to project the image from rear of the screen. 1111 Press ▲▼ to select [Rear] and then press the button. 2222 Press ▲▼ to change the image.
Sound Select [Sound] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Control panel Remote control Volume 1111 Press ▲▼ to select [Volume] and then Press the button. 2222 Press ◄► to adjust the volume. Operation Adjustment Adjustment range Press ►. turn up the volume Maximum value 63 Press ◄.
Setting Select [Setting] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel Menu position This function is used to change the position of the OnScreen Menu. 1111 Press ▲▼ to select [Menu position]. 2222 Press the button to change the position. zz The Menu position changes each time you press button as follows: the center → the bottom left → the bottom right → the top left → the top right → the center...
Setting Select the background screen for when no input signal is detected. 1111 Press ▲▼ to select [Background]. 2222 Press the button. 3333 Press ▲▼ to switch between each option as below. Blue Blue colored background. User The logo transferred by "Logo Transfer Software *1 " is projected. Black Black colored background. ***** " Logo Transfer Software" is included on the supplied CD-ROM.
Setting JJLogo PIN code change Logo PIN code can be changed to your desired fourdigit number. 1111 Press ▲▼ to select [Logo PIN code change]. 2222 Press the button. zz Current logo PIN code dialog box appears. 3333 Press ▲▼ to enter the current code. Terminal The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer 2 input or monitor output. 1111 Press ▲▼ to select [Terminal] and then press the button. 2222 Press ▲▼ to switch the item.
Setting Direct on The P-timer display 000:00 appears on the screen and the count up starts. (000:00-180:00) Count up 1111 Press ▲▼ to select [Direct on] and then press the button. 2222 Press ▲▼ to switch between On and Off. zz When this function is set to [On], the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. zz Be sure to turn off the projector properly.
Setting Closed caption The closed caption is mainly used in the north America. This function shows the text information contained in the image signal. Captions may not be displayed on some devices or software. 1111 Press ▲▼ to select [Closed caption]. 2222 Press ► or the button to enter the submenu. JJClosed caption 1111 Press ▲▼ to select [Closed caption] and then press the button. 2222 Press ▲▼ to select Off, CC1, CC2, CC3 or CC4.
Setting Security This switching function prevents remote control interference when operating several projectors or video equipment at the same time. This function allows you to use the Key lock and PIN code lock function to set the security for the projector operation. 1111 Press ▲▼ to select [Remote control]. 2222 Press ► or the button. 3333 Press ▲▼ to select one among the seven codes. 1111 Press ▲▼ to select [Security]. 2222 Press ► or the button to access the submenu.
Setting JJPIN code change The PIN code can be changed to your desired fourdigit number. 1111 Press ▲▼ to select [PIN code change] and then Press button. have less cooling effect). Note zzFailure to set the running speed of cooling fans properly may affect the projector life. zzThe fan noise becomes louder in [On 1] and [On 2]. zz Current Pin code dialog box appears. 2222 Press ▲▼ to enter the current code. Press ► button to fix the number and move the red frame pointer to the next box.
Setting Filter counter This function is used to set a frequency for the filter replacement. 1111 Press ▲▼ to select [Filter counter]. 2222 Press ►or the button to access the submenu items. JJFilter counter Show the total accumulated time of the filter use timer setting. Factory default This function returns all setting values except for the [PIN code lock], [Logo PIN code lock], [Lamp runtime], [Filter counter] and the logo transferred by "Logo Transfer Software" to the factory default settings.
Information Select [Information] from the Main Menu (see “Navigating through the menu” on page 32), then select the item from the sub-menu. Remote control Control panel JJLamp power The selected lamp mode is displayed. JJLamp runtime The cumulative lamp operating time is displayed. JJPower management [Off] , [Ready] or [Shut down], and [timer] are displayed. JJKey lock The selected Key lock icon is displayed.
LAMP and WARNING Indicators Managing the indicated problems If a problem should occur inside the projector, the , and/or indicators will inform you. Manage the indicated problems as follow. CAUTION zz Before you take a remedial measure, follow the procedure of switching the power off indicated in “Turning Off the projector”. (Æpage 27) zz If multiple indicators light or blink, verify the status of the projector by looking at each indicator.
Replacement Before replacing the unit zz When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect the power plug from the wall outlet. (Æpages 23, 27) zz Be sure to observe the procedure “Turing Off the projector” (Æpage 27) when performing power supply operation. Maintenance JJOuter Case Wipe off dirt and dust using a soft dry cloth. zz If the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping.
Replacement Replacing the unit JJAir filter unit Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, replace the air filter unit immediately. Replace it with the separately sold ET-RFT100 replacement filter unit.
Replacement JJLamp unit The lamp unit is a consumable component. You can check the total usage time using Lamp runtime in the Information menu on page 56. It is recommended to ask an authorized engineer to replace the lamp unit. Contact your dealer. Consult your dealer to purchase a replacement lamp unit (ET-LAT100). CAUTION: ■ Do not replace the lamp unit when it is hot. (Wait at least 1 hour after use.) The inside of the cover can become very hot, take care to avoid burn injuries.
Replacement JJ Replacing the Lamp unit CAUTION: zz When the projector is mounted on a ceiling, do not work with your face close to the projector. zz Attach the lamp unit and the lamp cover securely. zz When you experience difficulty in installing the lamp, remove it and try again. If you use force to install the lamp, the connector may be damaged. 1111 Turn off the Power by following the procedure in "Turning Off the projector" (Æpage 27). Unplug the AC power cord.
Replacement Attaching the Lens Cover When moving this projector or while not using it over an extended period of time, attach the lens cover. Attach the lens cover according to the following procedures. 1111 Thread the string through the hole on the lens cover and then tie a knot in the string to secure it in place. 2222 To pass the other end of the string into the hole on the bottom of the projector and pull at it.
Troubleshooting Please check following points. For details, see the corresponding pages. Reference page Cause zz The power cord may not be connected. — zz No electric supply is at the wall outlet. — Power does not turn zz The circuit breakers have tripped. on. zz Is the indicator, indicator, or indicator lit or blinking? — 24, 57 zz The lamp cover has not been securely installed.
Troubleshooting Problem Picture from a HDMI device does not appear or picture is not stable. No sound is output from a HDMI device. Cause zz Is the HDMI cable securely connected? 22 zz Turn off the power of the projector and the connected devices. Then turn — zz Isn't unsupported signal cable connected? 69 zz Set the sound channel of the attached device to Linear PCM.
Technical Information Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connector. JJConnection Connecting terminals on projector Computer D-Sub 9-pin (male) D-Sub 9-pin (female) Communication cable JJPin assignments and signal names D-Sub 9-pin (male) Outside view Pin No.
Technical Information JJBasic format Transmission from the computer begins with STX, then the command, parameter, and ETX are sent in this order. Add parameters according to the details of control. STX C1 C2 C3 P1 Colon (1 byte) 3 command characters (3 bytes) Start (1 byte) : P2 Pn Parameter (undefined length) ETX End (1 byte) ½½½ When sending commands without parameters, a colon (:) is not necessary.
Technical Information JJCable specifications [When connected to a computer] Projector 1 2 3 4 5 6 7 8 9 NC NC NC NC 1 2 3 4 5 6 7 8 9 Computer (DTE specifications) JJControl commands When controlling the projector from a computer, the following commands are available: [Projector control command] Control contents PON Power [ON] POF Power [OFF] Remarks IIS INPUT selection (Parameter) VID = Video SVD = S-video RG1 = Computer 1(RGB) RG2 = Computer 2(RGB) HD1 = HDMI SCT = Computer 1(Scart) OSH
Technical Information Other terminals JJPin assignments and signal names of terminal Pin No. Outside view Signal names GND (luminance signal) GND (color signal) Luminance signal Color signal JJPin assignments and signal names of terminal Pin No. Outside view Signal names R/PR G/G SYNC/Y B/PB +5V DDC data HD/SYNC VD DDC clock : Not assigned - , , : GND terminals JJPin assignments and signal names of terminal Pin No.
Technical Information List of compatible signals The following table specifies the types of signals compatible with the projectors. Format : V = VIDEO, S = S-VIDEO, C = COMPUTER, Y = YPBPR, H = HDMI H (kHz) V (Hz) NTSC/NTSC 4.43/ PAL-M/PAL 60 720 x 480 15.7 59.9 PAL/PAL-N/SECAM 720 x 576 15.6 480p 640 x 480 31.47 Mode Dot clock Picture frequency quality *2 (MHz) A V/S 60.0 -- A V/S 59.88 25.2 A 480i 640 x 480i 15.734 60.00 12.2727 A 768 x 576 31.25 50.00 29.
Technical Information Mode SXGA + Display resolution *1 (dots) 1400 x 1050 1024 x 768 XGA 1024 x 768i 1152 x 864 1152 x 900 1280 x 960 SXGA 1280 x 1024 1280 x 1024i UXGA 1600 x 1200 Scanning frequency Dot clock Picture frequency quality *2 (MHz) H (kHz) V (Hz) 63.970 60.190 107.99 A 65.350 60.120 122.85 A 65.120 59.900 122.43 A 48.36 60.00 65.00 A 84.977 94.504 A ○ 60.023 75.03 78.75 A ○ 56.476 70.07 75.00 A ○ 60.31 74.92 79.252 A 48.50 60.02 65.179 A 44.
Technical Information Mode Display resolution *1 (dots) 1280 x 768 WXGA 1280 x 800 1366 x 768 1360 x 768 WSXGA+ 47.776 59.870 79.50 AA 60.289 74.893 102.25 AA 68.633 84.837 117.50 AA 55.993 69.991 94.964 AA 57.675 72.004 97.817 AA 49.600 60.050 79.360 AA 41.200 50.000 68.557 AA 49.702 59.810 83.500 AA 63.980 60.020 108.00 AA 58.289 69.975 98.858 AA 60.044 71.995 102.795 AA 62.790 74.928 106.492 AA 71.553 84.879 122.498 AA 48.36 60.00 86.67 A 47.
Technical Information Mode Display resolution *1 (dots) 1360 x 768 1366 x 768 1376 x 768 1280 x 768 D-WXGA 1280 x 800 1280 x 768 D-SXGA 1280 x 1024 Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) 47.700 60.00 86.670 A 56.160 72.000 100.19 A 46.500 50.000 67.40 A 48.360 60.00 86.67 A 48.360 60.00 86.67 A 47.776 59.870 79.50 AA 60.289 74.893 102.25 AA 68.633 84.837 117.50 AA 49.572 59.870 83.282 AA 41.200 50.000 68.557 AA 49.702 59.810 83.
Specifications Model No. Power supply PT-TW230E AC100 V - 240 V 50 Hz/60 Hz 100 V - 240 V 3.6 A-1.8 A 310 W Power consumption When [Standby mode] of [Setting] is set to [ECO]: 0.42 W When [Standby mode] of [Setting] is set to [Network]: 9.5 W Panel size Display method Drive method Pixels Active matrix method 1 024 000(1 280 x 800) x 3 panels Manual focus F 1.8 , f 6.
Specifications Model No. COMPUTER IN 1/ COMPONENT IN COMPUTER IN 2/ MONITOR OUT Terminals VIDEO IN S-VIDEO IN HDMI IN AUDIO IN AUDIO OUT CONTROL PORT LAN PT-TW230E 1 (D-sub 15 pin female) [RGB signal] 0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 [p-p] 75 Ω HD/SYNC TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible [YPBPR signal] Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω [RGB signal] 0.
Specifications Dimensions ½½½ Actual dimension may differ by product. 6.29(159.8) 6.56(166.7) 5.65(143.4) 0.34(8.7) 2.51(63.8) 7.53(191.3) 4.33(110) 4.23(115) 0.70(17.9) 1.14(29) 1.46(37.1) 0.55(14) 0.56(14.2) 0.72(18.4) 3.54(90) 6.78(172.1) 1.65(42) 2.76(70) 4.16(105.7) 5.46(138.7) 13.78(350) 7.09(180) 7.09(180) 5.60(142.2) 3.94(100) 6.77(172) 15.11(383.
Index A About Your Projector.......................15 Accessories.....................................13 Adjusting front adjustable feet.........21 Attaching the Lens Cover................62 AUTO PC adjust..............................37 Auto setup.......................................48 AV MUTE.........................................31 B Background.....................................49 Basic operations by using the remote control..........................................29 Blackboard(Green)..........
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
