S P E P ro d u c t N u m b e r : PT-LZ370 P ro d u c t N a m e : LCD Projector C F I L E As of December 2011. Specifications and appearance are subject to change without notice.
S P E C F I L E PT-LZ370 LCD Projector Specifications Main unit Power supply Power consumption LCD* 2 panel Panel size Display method Drive method Pixels Lamp* 3 Lens Projection size Throw distance Colors Brightness* 4 Center-to-corner uniformity ratio* 4 Contrast ratio* 4 Resolution Scanning frequency HDMI RGB YPBPR (YCBCR) Video/S-Video Optical axis shift* 6 Keystone correction range Installation On-screen menu languages Terminals HDMI IN COMPUTER (RGB) IN RGB signal 100 – 240 V AC, 50/60
S P E C F I L E PT-LZ370 LCD Projector AUDIO IN AUDIO OUT SERIAL IN LAN Power cord length Cabinet materials Dimensions (W × H × D) Weight* 8 Operation noise* 4 Operating temperature Operating humidity Remote control unit Power supply Operation range* 9 Dimensions (W × H × D) Weight M3 (L, R) × 1, 0.5 Vrms, impedance 22 kilohms or more M3 (L, R) × 1 (monitor out: 0 – 2.
S P E F C I L E PT-LZ370 LCD Projector 380 (14-31/32) 345 (13-19/32) Dimensions 95 (3-3/4) (5-15/16) 151 (9/16) 14 137 (5-13/32) 74 (2-15/16) 35 (1-3/8) unit : mm (inch) NOTE: This illustration is not drawn to scale.
S P E C F I L E PT-LZ370 LCD Projector Standard setting-up position ∅43 (1-11/16 ) Upper edge of projected image Adjustable in 20 mm ( 25/32) steps ∅49 (1-15/16 ) 370.5 – 450.5 (14-19/32–17-3/4) unit : mm (inch) H L 230 (9-1/16) H Projected image L Lower edge of projected image 65 (2-9/16) Illustrations show the projector installed using optional ceiling mount bracket ET-PKA110H. This illustration is not drawn to scale.
S P E C F I L E PT-LZ370 LCD Projector Calculation of the projection distance For a screen size different from the chart shown on the page 5, use the equation below to calculate the projection distance. 16:9 minimum maximum L (m) = (diagonal screen size in inches) × 0.0292 - 0.054 L (m) = (diagonal screen size in inches) × 0.0583 - 0.041 NOTE: The accuracy of calculated value by the formula shown above is ±5%.
S P E F C I L E PT-LZ370 LCD Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 91 kHz, vertical scanning frequencies of 24 Hz to 85 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,920 × 1,080 pixels.
S P E F C I L E PT-LZ370 LCD Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names 6 No. 1 2 3 4 5 9 1 5 Signal name – TXD RXD – GND Description NC Transmitted data Received data NC Ground No.
S P E C F I L E PT-LZ370 LCD Projector Control commands Command: Function Callback: PON * 1 POF * 1 AVL: IIS: OST OFZ: OEN VPM:NAT VPM:STD VPM:CIN VPM:DYN VPM:DIC VPM:BBD VPM:WBD VS1:00 VS1:01 VS1:05 VS1:06 VS1:09 AUU AUD OMN OCU OCD OCL OCR OAS OSH * 1/* 2 TSD: TST:
S P E C F I L E PT-LZ370 LCD Projector Parameter format Parameter format Size (Byte) Definition 3 (1 or 2 bytes also Decimal without signs: 0 –999 (000, 001, 002...999) possible when Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99) under control) Callback from the projector is 3 Byte.
S P E C F I L E PT-LZ370 LCD Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 100 mm (3-15/16˝ ) or more around the projector’s air intake openings. 3.
