S P E P ro d u c t N u m b e r : PT-F300 P ro d u c t N a m e : LCD Projector C F I L E As of October 2008. Appearance and specifications are subject to change without notice.
S P E C F I L E PT-F300 LCD Projector Specifications Power supply Power consumption Optical system LCD panel Panel size Display method Drive method Pixels Pixel configuration Lens Lamp Colors Brightness * 1 Center-to-corner uniformity * 1 Contrast ratio* 1 Resolution RGB Scanning frequency RGB YPBPR S-Video/Video Projection size Throw distance Optical axis shift Keystone correction range Installation On-screen menu Built-in speakers Terminals Size Output power DVI-D IN COMPUTER (RGB) 1 R, G
S P E F C I L E PT-F300 LCD Projector Power cord length Cabinet material Dimensions (W x H x D) Weight * 2 Operating environment Remote control unit VIDEO IN RCA pin x 1, 1.0 Vp-p, 75 ohms S-VIDEO IN Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms COMPUTER AUDIO IN 1 M3 (stereo) x 1, 0.5 Vrms, for COMPUTER 1 COMPUTER AUDIO IN 2 M3 (stereo) x 1, 0.5 Vrms, for DVI-D and COMPUTER 2 AUDIO IN RCA (L, R) x 1, 0.
S P E F C I L E PT-F300 LCD Projector Dimensions 323 (12-23/32˝) unit : mm (inch) NOTE: This illustration is not drawn to scale. 13.5 (17/32˝) 53 (2-3/32˝) 432 (17˝) 311 (12-1/4˝) 115 (4-17/32˝) 128.
S P E F C I L E PT-F300 LCD Projector Standard setting-up positions 369 – 449 H Upper edge of projected image (14-17/32˝– 17-11/16˝) Adjustable in 20-mm (15/32-inch) step unit : mm (inch) Ø49 (1-15/16˝) Ø42 (1-21/32˝) L 199 Projected image (7-27/32˝) H L Lower edge of projected image L: Distance to screen H: Height from the edge of screen to center of lens NOTE: 65 W 70 (2-3/4˝) Illustrations show the projector installed using optional ceiling bracket.
S P E F C I L E PT-F300 LCD Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. H (Width of projected image) 0.27H Standard postition of projected image 0.5V V (Height of projected image) 0.5V 0.27H Installable angle Install the projector at an angle within the range shown below.. • Horizontal direction The projector may not be angled horizontally.
S P E F C I L E PT-F300 LCD Projector Computer data compatibility This projector accepts up to 91 kHz horizontal scanning frequency and 162 MHz dot clock. NOTE: Pixel thinning is applied to signals that exceed a dot clock frequency of 150 MHz. The display resolution of this projector is 1,024 x 768 pixels. If the display resolution indicated in the above data exceeds this resolution, image compression will be used to convert the input signal to 1,024 x 768 pixels.
S P E F C I L E PT-F300 LCD Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names 6 9 1 5 No. Signal name Description No.
S P E C F I L E PT-F300 LCD Projector Control commands Command: Function Callback: PO N * 1 PO F * 1 AV L : < p l > II S : < i n p u t s i g n a l > OS T OF Z : < o f f o n > OE N OX G : 0 OX G : 1 OX G : 2 VP M : < N A T > VP M : < S T D > VP M : < C I N > VP M : < D Y N > VP M : < B B D > VX X : D L V I 0 = < + 0 0 0 0 0 > VX X : D L V I 0 = < + 0 0 0 0 1 > VX X : D L V I 0 = < + 0 0 0 0 2 > AU U AU D OM N OC U OC D OC L OC R OA S OS H * 1/* 2 OI X DZ U DZ D TS D : < d
S P E C F I L E PT-F300 LCD Projector Parameter format Parameter format Size (Byte) Definition 3 (1 or 2 bytes also possible when under control) 1 3 1 3 3 1 4 1 8
S P E C F I L E PT-F300 LCD Projector Notes on Projector Placement and Operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector's exhaust openings.
