S P E C F I L E P ro d u c t N u m b e r : PT-EZ770Z/EZ770ZL P ro d u c t N a m e : LCD Projectors As of October 2013. Specifications and appearance are subject to change without notice.
PT-EZ770Z/EZ770ZL LCD Projectors Specifications Main unit Power supply Power consumption Optical system LCD panel Panel size Display method Pixels Pixel configuration Lens Lamp Screen size Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency DisplayPort/HDMI/DVI-D RGB YPBPR (YCBCR) Video/YC Optical axis shift 100–240 V AC, 50/60 Hz 590 W (0.3 W with STANDBY MODE set to ECO* 1 , 10 W with STANDBY MODE set to NORMAL, 37 W with in STANDBY MODE of Audio Setting set to on.
PT-EZ770Z/EZ770ZL LCD Projectors Terminals DisplayPort IN HDMI IN DVI-D IN RGB1 IN R, G, B Y, PB (CB), PR (CR) DP-20P × 1, HDCP compatible 480p(525p), 576p(625p), 720(750)/60p, 720(750)50p, 1080(1125)/60i, 1080(1125)/50i, 1080(1125)/25p, 1080(1125)/24p, 1080(1125)/24sF, 1080(1125)/30p, 1080(1125)/60p, 1080(1125)/50p VGA (640 × 480) – WUXGA* 4 (1,920 × 1,200) Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.
PT-EZ770Z/EZ770ZL LCD Projectors Power cord length Cabinet materials Dimensions (W × H × D) PT-EZ770Z PT-EZ770ZL Weight* 6 Operation noise* 2 Operating temperature Operating humidity Remote control unit Power supply Operation range* 8 Dimensions (W × H × D) Weight PT-EZ770Z PT-EZ770ZL 3.0 m (9 ft 10 in) Molded plastic 530 × 177* 5 × 445 mm (20-7/8 × 6-31/32 * 5 × 17-17/32 inches) (with supplied lens) 530 × 177* 5 × 385 mm (20-7/8 × 6-31/32 * 5 × 15-5/32 inches) (without lens) Approx. 10.6 kg (23.
PT-EZ770Z/EZ770ZL LCD Projectors 385 (15-5/32) 445 (17-17/32) Dimensions 80 (3-5/32) 17 530 (20-7/8) (21/32) 160 (6-5/16) 177 (6-31/32) 60 (2-3/8) unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-EZ770Z.
PT-EZ770Z/EZ770ZL LCD Projectors *1 When the lens protrudes to the maximum. A: 79.5 mm (3-1/8 in) with the ET-ELW20 60 mm (2-3/8 in) with the supplied lens 84 mm (3-5/16 in) with the ET-ELT20 80 mm (3-5/32 in) with the ET-ELT21 50 mm (1-31/32 in) with the ET-ELW21 *2 Adjustable in 30 mm (1-3/16 in) steps.
PT-EZ770Z/EZ770ZL LCD Projectors Projection distance for 16:10 aspect ratio screen Unit: meters Distance to screen (L) Screen size (diagonal) Zoom ET-ELW20 Zoom lens [m] Supplied lens Fixed-focus ET-ELT20 Zoom lens ET-ELT21 Zoom lens Height from the edge of screen to center of lens (H) ET-ELW21 Fixed-focus lens Zoom lenses Fixedfocus lens [in] min. max. min. max. min. max min. max. 1.02 / 40 1.02 1.41 1.36 2.35 2.29 3.81 3.72 6.03 0.63 -0.05 – 0.59 0.27 1.27 / 50 1.29 1.
PT-EZ770Z/EZ770ZL LCD Projectors Projection distance for 16:9 aspect ratio screen Unit: meters Distance to screen (L) Screen size (diagonal) Zoom ET-ELW20 Zoom lens [m] Supplied lens Fixed-focus ET-ELT20 Zoom lens ET-ELT21 Zoom lens Height from the edge of screen to center of lens (H) ET-ELW21 Fixed-focus lens Zoom lenses Fixedfocus lens [in] min. max. min. max. min. max min. max. 1.02 / 40 1.05 1.45 1.40 2.42 2.36 3.92 3.83 6.20 0.65 -0.05 – 0.55 0.25 1.27 / 50 1.32 1.
PT-EZ770Z/EZ770ZL LCD Projectors Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 ET-ELW20 minimum maximum L (m) = (diagonal screen size in inches) × 0.026816 - 0.055497 L (m) = (diagonal screen size in inches) × 0.036511 - 0.053400 Supplied lens minimum maximum L (m) = (diagonal screen size in inches) × 0.035305 - 0.054882 L (m) = (diagonal screen size in inches) × 0.060045 - 0.
PT-EZ770Z/EZ770ZL LCD Projectors Shift range Optical axis shift function allows to shift the position of a projected image as shown below. H (Width of projected image) 0.1H Standard postition of projected image 0.6V V (Height of projected image) 0.6V 0.1H • The ET-ELW21 is a fixed short-focus lens. Therefore, the lens shift function provided in the main unit cannot be used. Installable angle Install the projector at an angle within the range shown below.
PT-EZ770Z/EZ770ZL LCD Projectors List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,920 × 1,200 pixels.
PT-EZ770Z/EZ770ZL LCD Projectors Display mode Display resolution (dots)* 1 1280 × 720 1280 × 720 1280 × 768 1280 × 800 1366×768 Format DisplayPort/HDMI/ DVI-D/RGB 1280 × 768 49.8 59.9 100.0 120.0 49.9 60.5 74.5 131.8 161.6 65.3 1280 × 768 * 2 47.4 60.0 68.3 1280 × 768 47.8 60.3 68.6 41.3 49.3 59.9 74.9 84.8 50.0 59.9 79.5 102.3 117.5 68.6 71.0 49.7 62.8 71.6 60.0 52.4 64.0 72.3 78.2 80.0 91.1 39.6 47.7 54.1 64.0 65.2 65.3 78.8 82.2 59.8 74.9 84.9 60.0 50.0 60.0 66.3 72.0 75.0 85.0 49.
PT-EZ770Z/EZ770ZL LCD Projectors Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names 6 No. 1 2 3 4 5 9 1 5 Signal name – TXD RXD – GND Description NC Transmitted data Received data Connected internally Ground No.
PT-EZ770Z/EZ770ZL LCD Projectors Cable specifications Control commands * Command : Parameter Function PON POF OSH:0 OSH:1 IIS:DL1 IIS:DP1 IIS:HD1 IIS:DVI IIS:RG1 IIS:RG2 IIS:VID VXX:RYC2=+00 000 VXX:RYC2=+00 001 VXX:LPWI1=+0 0030 VXX:LPWI1=+0 0001 VXX:LPWI1=+0 0020 VXX:LPWI1=+0 0021 OAS VSE:0 VSE:1 VSE:2 VSE:5 VSE:6 VSE:9 VSE:10 VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:DIC Standby power Shutter Input selection RGB2 INPUT SETTING Lamp power Callback On Off Off On DigitalLink DisplayPort HDMI DVI-D RGB1 R
PT-EZ770Z/EZ770ZL LCD Projectors Status request commands Command : Parameter QPW Function Main power status QSH Shutter function status QIN Input signal status QVX:LPWI1 Lamp power mode status QSE Aspect mode status QPM Picture mode status QST Q$L:1 QTM:0 QTM:1 Projector run time Lamp run time Temperature status Callback 000 001 0 1 DL1 DP1 HD1 DVI RG1 RG2 VID VXX:LPWI1=+00030 VXX:LPWI1=+00001 VXX:LPWI1=+00020 VXX:LPWI1=+00021 0 1 2 5 6 9 10 NAT STD DYN CIN DIC p1p2p3p4p5 p1p2p3p4 p1p2p3p4/p5
PT-EZ770Z/EZ770ZL LCD Projectors Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector. 2. Make sure there is an unobstructed space of 1,000 mm (3 feet 3 inches) or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.
LCD Projectors PT-EZ770Z/EZ770ZL Direction of air intake and exhaust Intake Exhaust Operating the projector continuously 1. If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration becomes shorter. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods. Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
