S P E C F I L E The PT-DZ6710L is not equipped with a lens. P ro d u c t N u m b e r : PT-DZ6710/DZ6710L P ro d u c t N a m e : DLP ™ Projectors As of February 2009. Specifications subject to change without notice.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Specifications Main Unit Power supply: Power consumption: North America: Europe: North America: Europe: DLP™ chip: Lens: Panel size: Display method: Pixels: PT-DZ6710: PT-DZ6710L: Lamp: Screen size: Brightness* 2 : Center-to-corner uniformity* 2 : Contrast* 2 : Resolution: Scanning frequency: RGB/DVI-D: YPBPR (YCBCR): S-Video/Video: Optical axis shift: Keystone correction range: Installation: Terminals * 3 : SDI IN: DVI-D IN: As of Febru
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors RGB 1 IN: R, G, B: Y, PB, PR: BNC x 5 R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD/VD, SYNC: High impedance, TTL (positive/negative), 75 ohms Y: 1.0 Vp-p (including sync signal), P B/PR: 0.7 Vp-p, 75 ohms NOTE: HD/SYNC, and VD terminals do not accept tri-leve sync signals. RGB 2 IN: R, G, B: D-sub HD 15-pin x 1 R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.
S P E F C I L E PT-DZ6710/DZ6710L DLP ™ Projectors 423 (16-21/32˝) 9 (11/32˝) 77.5 (3-1/16˝) 20 (25/32˝) 155 (6-3/32˝) 175 (6-7/8˝) 17 (21/32˝) unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-DZ6710.
P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors (when installed using the ET-PKD56H) *2 340– 420 (13-3/8˝– 16-17/32˝) Standard setting-up position H Upper edge of projected image 416– 496 (16-3/8˝– 19-17/32˝) S L *2 Adjustable in 40 mm (1-9/16˝) steps. *1 Projected image *1 When the lens protrudes to the maximum.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Projection distance for 16:10 aspect ratio screen Unit: millimeters Screen size (inch, diagonal) Distance to screen (L) Zoom Fixed-focus Zoom lenses Fixedfocus lens* ET-DLE150 Zoom lens Supplied lens ET-DLE250 Zoom lens ET-DLE350 Zoom lens ET-DLE450 Zoom lens min. max. min. max. min. max. min. max. min.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Projection distance for 16:9 aspect ratio screen Unit: millimeters Screen size (inch, diagonal) Distance to screen (L) Zoom Fixed-focus Zoom lenses Fixedfocus lens* ET-DLE150 Zoom lens Supplied lens ET-DLE250 Zoom lens ET-DLE350 Zoom lens ET-DLE450 Zoom lens min. max. min. max. min. max. min. max. min.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Projection distance for 4:3 aspect ratio screen Unit: millimeters Screen size (inch, diagonal) Distance to screen (L) Zoom Fixed-focus ET-DLE055 Fixed-focus lens Height from the edge of screen to center of lens (H) Zoom lenses Fixedfocus lens* ET-DLE150 Zoom lens Supplied lens ET-DLE250 Zoom lens ET-DLE350 Zoom lens ET-DLE450 Zoom lens min. max. min. max. min. max. min. max. min. max.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 ET-DLE150 minimum maximum L (mm) = (diagonal screen size in inches) x 28.6 – 54.0 L (mm) = (diagonal screen size in inches) x 41.3 – 49.8 Supplied lens minimum maximum L (mm) = (diagonal screen size in inches) x 39.5 – 74.5 L (mm) = (diagonal screen size in inches) x 52.9 – 73.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • Floor mount • Ceiling mount H 0.5V V 0.1H Standard postition of projected image 0.5V V (Height of projected image) 0.1H (Height of projected image) (Width of projected image) Standard postition of projected image 0.1H 0.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors List of compatible signals This projector supports RGB signals with horizontal frequencies of 15 to 91 kHz, vertical frequencies of 50 to 85 Hz and up to 162 MHz dot clock. NOTE: The native resolution of this projector is 1,920 x 1,200 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
S P E F C I L E PT-DZ6710/DZ6710L DLP ™ Projectors Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names No. Signal name Description 1 – NC No.
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Cable specifications Projector 1 PC (DTE) NC NC 2 2 3 3 4 NC NC NC NC 6 7 7 8 8 9 4 5 5 6 1 NC NC 9 Control commands * Command : Parameter Function PON POF IIS:SDI IIS:DVI IIS:RG1 IIS:RG2 IIS:VID IIS:SVD LPM:0 LPM:1 LPM:2 LPM:3 OSH:0 OSH:1 OFZ:0 OFZ:1 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA VXX:DLVI0=+00000 VXX:DLVI0=+00001 VXX:DLVI0=+00002 VXX:DLVI0=+00003 OTE:1 OTE:2 OTE:4 OTE:10 TSD:y1y2y3y4m1m2d1d2w TST:h1h2m1m2s1
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Status asking commands Command : Parameter Q PW Function Main power status Q SH Shutter function status Q FZ Freeze function status Q IN Input signal status Q OS On-screen display status Q ST Q $L:1 Q $L:2 Q SL Projector run time Lamp 1 run time Lamp 2 run time Lamp operation mode status Q LP Lamp power mode status Q PM Picture mode status Q VX:DLVI0 System daylight view status Q TM:0 Q TM:1 Q TM:2 Q GD Q GT Temperature status D
S P E C F I L E PT-DZ6710/DZ6710L DLP ™ Projectors Notes on Projector Placement and Operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another.
