S P E C F I L E P ro d u c t N u m b e r : PT-DZ10K P ro d u c t N a m e : 3-Chip DLP ™ Projector As of April 2013. Specifications and appearance are subject to change without notice.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Specifications Main unit Power supply Power consumption 120 V AC, 9 A, 50/60 Hz 220–240 V AC, 4.7 A, 50/60 Hz 120 V AC, 50/60 Hz 220–240 V AC, 50/60 Hz DLP™ chip 925 W (1,010 VA) (0.2 W with standby mode set to eco.*1 6 W with standby mode set to normal. Both with fan stopped.) 900 W (980 VA) (0.3 W with standby mode set to eco.*1 9 W with standby mode set to normal. Both with fan stopped.) Panel size 24.4 mm (0.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Keystone correction range Vertical ±40°, horizontal ±15° (vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6) When using only the KEYSTONE correction of the Geometric Adjustment function: Vertical ±40°, horizontal ±15° Ceiling/floor, front/rear Installation Terminals SDI IN BNC × 1, 3G-SDI signal: SMPTE ST 424 compliant HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 co
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Remote control unit Power supply Operation range* 8 3 V DC (AA/R6 type battery × 2) Dimensions (W × H × D) 5 in) when operated from directly in front of the Approx. 30 m (98 signal receptor 51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches) Weight Approx. 134 g (4.
S P E F C I L E PT-DZ10K 3-Chip DLP ™ Projector 540 (21-1/4) unit : mm (inch) NOTE: This illustration is not drawn to scale. 462 (18-3/16) 530 (20-7/8) 100 (3-15/16) 200 (7-7/8) 8.5 (11/32) 548.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector 䃥60.5 (12-3/8) H Upper edge of projected image L *1 Projected image 342 198 (7-13/16) (13-15/32) 2 436㹼516 * (17-5/32– 20-5/16) 2 340㹼420* (13-3/8– 16-17/32) Standard setting-up position *1 When the lens protrudes to the maximum.
S P E F C I L E PT-DZ10K 3-Chip DLP ™ Projector Projection distance for 16:10 aspect ratio screen (ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Unit: meters Screen size (diagonal) [m] / [in] Distance to screen (L) Zoom Fixed-focus ET-D75LE6 Zoom lens ET-D75LE10 Zoom lens ET-D75LE20 Zoom lens ET-D75LE30 Zoom lens ET-D75LE40 Zoom lens min. max. min. max. min. max. min. max. min. max.
S P E F C I L E PT-DZ10K 3-Chip DLP ™ Projector Projection distance for 16:9 aspect ratio screen (ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Unit: meters Screen size (diagonal) Distance to screen (L) Zoom ET-D75LE6 Zoom lens [m] / [in] ET-D75LE10 Zoom lens Fixed-focus ET-D75LE20 Zoom lens ET-D75LE30 Zoom lens ET-D75LE40 Zoom lens min. max. min. max. min. max. min. max. min. max.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 Zoom lenses ET-D75LE6 minimum maximum L (m) = (diagonal screen size in inches) × 0.0201 – 0.0566 L (m) = (diagonal screen size in inches) × 0.0241 – 0.0736 ET-D75LE10 minimum maximum L (m) = (diagonal screen size in inches) × 0.0284 – 0.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • When the lens except the ET-D75LE6 is mounted • When the ET-D75LE6 is mounted H H 0.15H 0.44V 0.12V 0.12V V 0.55V (Width of projected image) 0.44V 0.15H (Height of projected image) 0.2H 0.55V (Width of projected image) 0.12V 0.12V (Height of projected image) V 0.
S P E F C I L E PT-DZ10K 3-Chip DLP ™ Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,920 × 1,200 pixels.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Display mode Display resolution (dots) 1280 × 720 1280 × 720 1280 × 768 1280 × 768 1280 × 768 * 1280 × 768 1280 × 800 1280 × 800 1280 × 800 * 1280 × 800 MSXGA SXGA 1366×768 1366 × 768 SXGA+ 1400 × 1050 WXGA+ 1440 × 900 UXGA60 WSXGA+ 1600 × 1200 1680 × 1050 1920×1080 1920 1920 1920 1920 1920 1920 WUXGA * 1280 × 960 1280 × 1024 × × × × × × 1080 1080 * 1080 1200 1200 * 1200 Scanning frequency H V (kHz) (kHz) 37.1 44.8 76.3 92.
S P E F C I L E PT-DZ10K 3-Chip DLP ™ Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names No. 1 2 3 4 5 Signal name – TXD RXD – GND Description NC Send data Receive data NC Ground No.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Cable specifications Control commands * Command : Parameter Function PON POF OSH:0 OSH:1 IIS:SD1 IIS:HD1 IIS:DVI IIS:RG1 IIS:RG2 IIS:VID VXX:RYC1=+00000 VXX:RYC1=+00001 LPM:0 LPM:1 LPM:2 LPM:3 OLP:0 OLP:1 VSE:1 VSE:2 VSE:5 VSE:6 VSE:9 VSE:10 OPP:0 OPP:1 OPP:2 OPP:3 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA VPM:DIC VXX:DLVI0=+00000 VXX:DLVI0=+00001 VXX:DLVI0=+00002 VXX:DLVI0=+00003 OTE:4 OTE:9 OTE:10 OTE:p1p2p3p4 TSD:y1y2y3y4m1m2d1d2w TST:h1h2m1
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Status request commands Command : Parameter QPW Function Main power status QSH Shutter function status QIN Input signal status QSL Lamp operation mode status QLP Lamp power mode status QPP P in P status QPM Picture mode status QVX:DLVI0 System daylight view status QST Q$L:1 Q$L:2 QTM:0 QTM:1 QTM:2 QGD QGT QOS Projector run time Lamp 1 run time Lamp 2 run time Temperature status Callback 000 001 0 1 SD1 DVI-D RG1 RG2 VID 0 1 0 1 0 1 2
S P E F C I L E PT-DZ10K 3-Chip DLP ™ Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another.
S P E C F I L E PT-DZ10K 3-Chip DLP ™ Projector Direction of air intake and exhaust SDI VIDEO RGB1 RGB2 S-VIDEO DVI-D/HDMI MENU AUTO SETUP ENTER LENS SHUTTER Intake Exhaust Operating the projector continuously 1. If the projector is to be operated continuously one week, use the dual-lamp optical system’s alternating lamp operation (lamp relay) function. The projector cannot be operated continuously one week in dual-lamp mode.
