S P E C F I L E The PT-DX800LS and PT-DX800LK are not equipped with a lens. P ro d u c t N u m b e r : P ro d u c t N a m e : PT-DX800S/DX800K PT-DX800LS/DX800LK DLP ™ Projectors As of December 2011. Specifications and appearance are subject to change without notice.
S P E C F DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK Specifications Main unit Power supply Power consumption 120 V AC, 60 Hz 220–240 V AC, 50/60 Hz DLP™ chip Lens Panel size Display method Pixels PT-DX800S/DX800K PT-DX800LS/DX800LK Lamp Screen size Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency DVI-D RGB YPBPR (YCBCR) Video/S-Video Optical axis shift Keystone correction range Installation Terminals DVI-D IN RGB 1 IN R, G, B 120 V AC, 7.
S P E C F I DLP ™ Projectors L E PT-DX800S/DX800K/DX800LS/DX800LK RGB 2 IN R, G, B D-sub HD 15-pin × 1 R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD/VD, SYNC: High impedance, TTL (positive/negative) NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals.
S P E F C DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK 9 (11/32) 20 (25/32) 155 (6-3/32) 77.5 (3-1/16) 175 (6-7/8) 43 (1-11/16) unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-DX800S/DX800K.
S P E C F DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK H Upper edge of projected image 416–496 (16-3/8– 19-17/32) *2 340–420 (13-3/8– 16-17/32) Standard setting-up position *1 When the A: 84 mm 43 mm 44 mm 45 mm 51 mm 95 mm 27 mm lens protrudes to the maximum.
S P E F C I DLP ™ Projectors L E PT-DX800S/DX800K/DX800LS/DX800LK Projection distance for 4:3 aspect ratio screen Unit: meters Screen size (diagonal) Distance to screen (L) Height from the edge of screen to center of lens (H) Zoom lens ET-DLE080 [in] min. max. min. max. min. max. min. max. min. max. min. max. With a zoom lens except ET-DLE080 1.27 / 50 0.81 1.01 1.34 1.97 1.78 2.51 2.36 3.78 3.71 5.68 5.53 8.91 0.00 – 0.38 0.04 – 0.38 1.52 / 60 0.98 1.22 1.
S P E F C DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK Projection distance for 4:3 aspect ratio screen Unit: meters Screen size (diagonal) ET-DLE055 fixed-focus lens Distance to screen (L) [m] [in] Unit: feet Screen size (diagonal) Height from the edge of screen to center of lens (H) ET-DLE055 fixed-focus lens Distance to screen (L) [m] [in] Height from the edge of screen to center of lens (H) 1.27 / 50 0.81 0.38 1.27 / 50 2.7 1.3 1.52 / 60 0.98 0.46 1.52 / 60 3.
S P E F C I L E PT-DX800S/DX800K/DX800LS/DX800LK DLP ™ Projectors Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • Floor mount • Ceiling mount (When the lens except the ET-DLE080 is mounted.) (When the lens except the ET-DLE080 is mounted.) H 0.1H Standard postition of projected image 0.5V (Height of projected image) V 0.5V V 0.
S P E C F DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 91 kHz, vertical scanning frequencies of 50 Hz to 85 Hz, and a dot clock of 150 MHz maximum can be input. NOTE: The native resolution of this projector is 1,024 × 768 pixels.
S P E F C I L E PT-DX800S/DX800K/DX800LS/DX800LK DLP ™ Projectors Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names 6 No. 1 2 3 4 5 9 1 5 Signal name – TXD RXD – GND Description NC Send data Receive data Connected internally Ground No.
S P E C F I DLP ™ Projectors L E PT-DX800S/DX800K/DX800LS/DX800LK Cable specifications Projector 1 PC (DTE) NC NC 2 2 3 3 4 NC NC NC NC 6 7 7 8 8 9 4 5 5 6 1 NC NC 9 Control commands * Command : Parameter Function PON POF IIS:DVI IIS:RG1 IIS:RG2 IIS:VID IIS:SVD LPM:0 LPM:1 LPM:2 LPM:3 OSH:0 OSH:1 OFZ:0 OFZ:1 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA VXX:DLVI0=+0 0000 VXX:DLVI0=+0 0001 VXX:DLVI0=+0 0002 VXX:DLVI0=+0 0003 OTE:1 OTE:2 OTE:4 OTE:10 TSD:y1y2y3y4 m1m2d1d2w T
S P E C F I L E PT-DX800S/DX800K/DX800LS/DX800LK DLP ™ Projectors Status request commands Command : Parameter QPW Function Main power status QSH Shutter function status QFZ Freeze function status QIN Input signal status QOS On-screen display status QST Q$L:1 Q$L:2 QSL Projector run time Lamp 1 run time Lamp 2 run time Lamp operation mode status QLP Lamp power mode status QPM Picture mode status QVX:DLVI0 System daylight view status QTM:0 QTM:1 QTM:2 QGD QGT Temperature status C
S P E C F DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector. 2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s exhaust openings. 3.
S P E C F DLP ™ Projectors I L E PT-DX800S/DX800K/DX800LS/DX800LK Operating the projector continuously 1. If the projector is to be operated continuously for 24 hours, use the dual-lamp optical system's alternating lamp operation (lamp relay) function. Continuously operating the projector for 24 hours in the duallamp mode is not recommended. Allow a minimum of two hours per day of non-operation time for each lamp if the projector is to be operated continuously for more than 22 hours. 2.
