Operating Instructions 3-chip DLP®-based Projector Commercial Use Models No. PT-DW100E Read these instructions completely before operating this unit.
Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic ® DLP based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required.
5 38 43 46 49 52 58 62 67 Display Option settings ････････････････････････････････････････････････････････ 68 Projector setup ････････････････････････････････････････････････････････････････ 75 P IN P ･････････････････････････････････････････････････････････････････････････ 83 Displaying the internal test pattern･･････････････････････････････････････････････ 85 Setting the security ････････････････････････････････････････････････････････････ 86 How to use network function ･････････････････････････････････
IMPORTANT SAFETY NOTICE WARNING: THIS APPARATUS MUST BE EARTHED. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV, January 18 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. WARNING: 1) Remove the plug from the wall outlet when this unit is not in use for a prolonged period of time.
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362. Check for the ASTA mark a or the BSl mark ` on the body of the fuse.
Precautions with regard to safety WARNING If a problem occurs (such as no image) or if you notice smoke or a strange smell coming from the projector, turn off the power and disconnect the power cord from the wall outlet. • Do not continue to use the projector in such cases, otherwise fire or electric shocks could result. • Check that no more smoke is coming out, and then contact an Authorized Service Centre for repairs. • Do not attempt to repair the projector yourself, as this can be dangerous.
• If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result. Do not place the projector into water or let it become wet. • Failure to observe this may result in fire or electric shocks. Do not disassemble the lamp unit. • If the lamp section breaks, it may cause injury. Do not place liquid containers on top of the projector. • If water spills onto the projector or gets inside it, fire or electric shocks could result.
Precautions with regard to safety (continued) CAUTION Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam. • Using the projector under such conditions may result in fire or electric shocks. When disconnecting the power cord, hold the plug, not the cord. • If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result.
once a year. • If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. • It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Centre to clean the projector when required. Please discuss with the Authorized Service Centre regarding cleaning costs.
Before Using Accessories Check that all of the accessories shown below have been included with your projector. Remote Control [N2QAYB000076 × 1] Batteries for Remote Control (AA) Power cord For U.K. [K2CT3YY00014 × 1] For Continental [K2CM3YY00007 × 1] Drop-prevention bracket Eye bolt [TPAHE86 × 4] Wire [TTRA0143 × 4] Caution when moving the projector The projection lens is susceptible to vibrations and impacts. Be sure to always remove the lens during transport.
clear images: •ToTheview audience cannot enjoy high-contrast and clear images if outside light or the illumination interferes the screen surface. Draw window curtains or blinds, turn off the lightings near the screen or take other proper measures. • In rare cases, wafture can occur on the screen affected by the warm air from the exhaust port depending on the environment. Make sure that there is no equipment in front of the set which will recirculate the exhaust air from the set or other nearby equipment.
Location and function of each part Remote control unit Front 1 2 3 l 4 5 m 6 n 7 o p 8 9 j q r s k 1 Remote control operation indicator lamp The lamp flashes when any remote control button is pressed. 2 POWER STANDBY button ･････････ (pp. 35, 37) When the projector is in projection mode with the MAIN POWER switch of the projector at the “ l ” side, this button switches the projector to standby mode. 3 POWER ON button ････････････････････ (p.
Top Getting Started Side u t Bottom l AUTO SET UP button･･････････････････ (p. 47) Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “PROGRESS...” appears on the screen. m SHUTTER button ･････････････････････ (p. 46) Press this button to black out the image temporarily. n ASPECT button ･･･････････････････････ (p. 48) Switches the image aspect ratio.
Location and function of each part (continued) Projector Main Unit Front Rear 1 2 7 8 9 j 3 45 6 k l m 1 Projection lens cover･･････････････････ (p. 34) 2 Projection lens (optional) Lens for projecting images on the screen. 3 Remote control receiver window (front) ･･････････････････････････････････････ (p. 17) This window receives the signal beam emitted from the remote control. 4 LAMP (LAMP1, LAMP2, LAMP3, LAMP4) monitor ･････････････････････････････ (p.
Controls Connection terminals (p. 16) 1 2 4 5 6 7 8 9 Controls 3 1 AC IN terminal ････････････････････････ (p. 35) Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket. 2 MAIN POWER switch･･････････････ (pp. 35-37) Use this switch to turn on “I” and off “○” the commercial line power applied to the projector. 3 Slot cover ････････････････････････････ (p. 29) Install the input module here. 4 POWER ON ( I ) button ････････････ (pp.
Location and function of each part (continued) Connection terminals 1 7 8 2 3 9 1 REMOTE1 lN/OUT terminal ････････････ (p. 18) When two or more main units are used in the system, they can be connected and controlled with a wired remote control cable (M3 jack). 2 REMOTE2 IN terminal ････････････････ (p. 108) The user can remotely control the main unit by using an external control circuit to this terminal (D-SUB 9-pin female). 3 SERIAL IN terminal････ (pp.
Loading batteries When loading supplied AA batteries into the battery compartment of the Remote Control, make sure that their polarities are correct. 1. Open battery compartment lid. • Open the lid in the order 1 and then 2. $ # 2. Insert the batteries. Effective range of remote control operation The Remote Control should normally be aimed at either the front or rear remote control receiver window on the projector (figure 1). The effective control range is approx.
Using the remote control unit (continued) Note • The Remote Control may not function properly if an object is in the light path. • The Remote Control receiver may not function properly in intense ambient light such as fluorescent lamps. Carefully site the projector so its Remote Control receiver windows will not be directly exposed to intense light.
Examples of system expansion The projector is provided with a number of terminals and optional accessories to enable various system expansions. Both input and output are provided to all terminals on the main unit. The following are some examples of system expansion: System 1 The optional high- or low-ceiling mount bracket flexibly fits the projector in individual site conditions. Getting Started Installation System 2 Connection to a computer via the DVI-D IN terminal or DVI-D input module (optional).
Installation (continued) Adjusting the feet The four adjustable feet (p. 14) mounted at the bottom of the projector are level-adjustable (0 mm–15 mm) which can be used when the floor surface is not horizontal. (Front) (Rear) Projection scheme This projector can use any of the four projection schemes. Select the most suitable scheme to the situation of your location. Use the INSTALLATION menu to choose the desired projection scheme. (p.
Every type of optional projection lenses has a different projection distance to achieve the same screen size. Select and purchase a projection lens most suitable to the size of your location referring to the following tables and the projection distances by the type of projection lenses on the next page.
Installation (continued) Projection distances by the type of projection lenses z For the screen aspect ratio of 4:3 (Units: m) Lens type Fixed-focus lens Zoom lens Model number of projection lens ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE6 ET-D75LE5 Throw ratio*1 2.0-2.7 : 1 2.7-4.1 : 1 4.1-6.9 : 1 6.9-11.0 : 1 10.9-20.6 : 1 1.4-1.6 : 1 1.0 : 1 Screen dimensions Projection distance (L) Screen Effective Effective size height width Min. (inch) (SH) (SW) Max. Min.
Calculation formulas for projection distance by lens types Model number of projection lens Throw ratio Aspect ratio Projection distance (L) formula (Units: m) 2.0-2.7 : 1 4:3 Minimal distance : L = 0.0419 × Screen diagonal (inch) - 0.0760 Maximal distance: L = 0.0560 × Screen diagonal (inch) - 0.1004 1.5-2.0 : 1 16:9 Minimal distance : L = 0.0343 × Screen diagonal (inch) - 0.0760 Maximal distance: L = 0.0458 × Screen diagonal (inch) - 0.1004 2.7-4.1 : 1 4:3 Minimal distance : L = 0.
Installation (continued) Installation dimensions diagram Figure 1 : Dimensions applying when Figure 2 : Dimensions applying when Figure 3 : Set rotation direction one unit is used two units are used) 30 cm or more 50 cm or more 30 cm or more Exhaust Exhaust 50 cm or more 50 cm or more Exhaust 50 cm or more +15° +15° +15° +15° OPEN FILTER CLEANING CLOSE 40 cm or more 10 cm or more 40 cm or more Attention • Leave a space of 50 cm or more behind the projector for replacing the lamp and ensuring t
Before starting connection • Before connection, read carefully the instruction manual for the device to be connected. • Turning off the power switch of the devices before connecting cables. • If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, prepare a necessary system connection cable to suit the device. • Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture.
Connection (continued) Example of connecting with VIDEO devices Control PC Control PC Control PC Video deck (TBC built-in) IN OUT REMOTE 1 RS-232C IN REMOTE 2 IN IN OUT VIDEO S-VIDEO IN R/PR G/Y SYNC/HD RGB 1 IN RS-422 IN SERIAL RS-422 OUT LAN B/PB VD RGB 2 IN DVI-D IN Red (connected to PR terminal) Blue (connected to PB terminal) Green (connected to Y terminal) Colour monitor Video deck (TBC built-in) DVD player DVD player with HDMI (HDCP) terminal Attention • When connecting with a
Control PC Control PC To 2nd projector (SERIAL IN terminal) IN OUT REMOTE 1 RS-232C IN REMOTE 2 IN RS-422 IN SERIAL Getting Started Example of connecting with personal computers RS-422 OUT LAN Control PC IN OUT VIDEO S-VIDEO IN R/PR G/Y SYNC/HD RGB 1 IN B/PB VD RGB 2 IN DVI-D IN I/F PC PC PC Attention • When the main power of the main unit is turned off, also turn off the power of the PC.
Installation of input module (optional) Installing the input module Types of the input modules (optional) Prepare beforehand an input module (optional) compatible with the input signals of the system. Module SD-SDI input module Module model No. ET-MD77SD1 Terminal BNC input × 1 BNC output × 1 RJ-45 input × 1 ET-MD77SD3 *1 DVI-D input module SMPTE259M compliant : 480i, 576i 10BASE-T/100BASE-TX BNC input × 1 BNC output × 1 SMPTE259M compliant : 480i, 576i SMPTE292M compliant : 720/60p, 720/59.
Procedure of installation IN OUT REMOTE 1 RS-232C IN REMOTE 2 IN RS-422 IN SERIAL MENU RS-422 OUT Getting Started Disconnect the power before installing the input module. LENS LAN POWER ON STANDBY VIDEO R/PR IN OUT VIDEO S-VIDEO IN G/Y SYNC/HD RGB 1 IN ENTER B/PB S-VIDEO RGB1 VD RGB 2 IN DVI-D IN RGB2 DVI-D AUTO SETUP SHUTTER LIGHT ON AUX OFF OFF AC IN ON MAIN POWER Slot Cover 1. Remove the slot cover. Remove 2 screws. 2. Insert the input module. Slot Input module 3.
Installation of input module (optional) (continued) Connecting signals to the input module When installing the projector, it is necessary to connect signals to the input module in accordance with the connecting equipment. Refer to the following diagram to establish proper signal connection.
SD-SDI input module (optional) ET-MD77SD1 (for 480i/576i) SD-SDI Module ET-MD77SD1 IN SERIAL OUT LAN LAN terminal*1 (10BASE-T/100BASE-TX) SD-SDI signal SD-SDI signal output (active through) Getting Started Connecting the signal to the SD-SDI input module Business digital VCR Note • If a source with an unstable signal is connected, errors in automatic signal recognition may occur. If this happens, use the SYSTEM SELECTOR menu to switch the format to the one which matches the signals being input.
Installation of input module (optional) (continued) Connecting the signal to the dual link HD/SD-SDI input module Dual link HD/SD-SDI input module (optional) ET-MD100SD4 Dual Link HD-SDI Module ET-MD100SD4 LINK-A SERIAL IN LINK-B HD-SDI or SD-SDI signal Business digital VCR • When connecting a single link signal, connect to the LINK-A terminal. • When connecting a dual link signal, connect to both the LINK-A and LINK-B terminals.
Getting Started Connecting signals to the DVI-D input module DVI-D input module (optional) ET-MD77DV DVI Module ET-MD77DV DVI-D IN *1 DVI-D signal PC with DVI output LAN terminal (10BASE-T/100BASE-TX) DVD player or high-vision video deck equipped with DVD/HDMI terminal • Pin assignments and signal names of DVI-D input terminal are listed in the table at right. 1 p q x Outside view Pin No. 1 2 8 9 LAN 3 4 5 6 7 8 9 j k l Signal Pin No. T.M.D.S data 2– T.M.D.S data 2+ T.M.D.
How to install and remove the projection lens (optional) Adjust the lens shift position so that it is at the home position (p. 39) before installing or removing the projection lens. 3. Push the projection lens cover in until it clicks into place. Attention • Remove the dust-proof sponge from the lens fitting of the projector before installing the projection lens. (Keep the dust-proof sponge in a safe place for later use if needed.
Projection Power indicator lamp OPEN FILTER CLEANING CLOSE This shows the power supply status. Make sure that you fully understand the operation of the power indicator lamp before operating the projector. Indicator status Off Projector status Main power is off Red Lit Standby mode POWER ON ( | ) button can be pressed so that images can be projected. Green Lit Images are being projected (on) Orange Lit Cooling mode After a short while, the projector will switch to standby mode.
Projection (continued) 6 3 5 4, 8-l 3 9 6 5 4, k 12 8 j 7 9 Powering up the projector 1 Connect the supplied power cable. (220 V-240 V, 50 Hz/60 Hz) 2 Press the “ | ” marked side of the MAIN POWER switch to turn on the power. • The power indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode. 3 Press POWER ON “ | ”.
3 1 2 1 2 Powering off the projector 1 Press POWER STANDBY “ ”. • A confirmation screen will appear. POWER OFF OK ENTER CANCEL CHANGE EXECUTE 2 Press ◄ or ► to select “OK” and press ENTER. (or press POWER STANDBY “ ” again.) Note • In the cooling state after the power is turned off, the lamp will not light up even if the power is turned on. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently.
How to adjust the lens How to adjust the focus, zoom and shift If the focusing, zooming or positioning of the image projected on the screen is not successful, even though the projector is properly positioned against the screen, you can adjust the focus, the zoom, or the vertical or horizontal position of the image. At the projector LENS FOCUS ADJUST LENS ZOOM ADJUST 1. Press LENS on the control panel of the main unit.
Adjustment range after lens position (optical shift) Do not move the lens beyond the bounds of the shift range as this may cause a change in the focus. This limitation is to protect the parts of the projector. Using the standard projection position as the reference, the optical axis shift function makes it possible to adjust the projection position in the ranges shown in the figures below. 0.20V 0.60V 0.20H 0.20V Projected screen height, V 0.30H 0.70V 0.20V Standard projection position 0.
How to adjust the lens (continued) How to adjust the lens mounter for addressing unevenness of focusing About the focus balance z Relation between the orientation of the lens and focus surface on the screen side If the projection lens is tilted in relation to the surface on which the images are formed, and the front (screen side) of the projection lens points downward (direction of broken arrow line) as shown in the example in the figure 1, the focus surface on the screen side is tilted so that its top
If the lens is heavy or the projector is installed so that it is tilted, the lens may be tilted, resulting in the focus becoming unbalanced. In such a case, refer to the figure 4 and table below, and follow the procedure below to perform adjustment. z Adjustment procedure 1 Switch to the focus adjustment mode with the remote control, and use the ▼ button to first offset the whole focus. 2 Use the ▲ button to stop at the place that first becomes just in focus in any of the directions of the screen.
How to adjust the lens (continued) z Precautions for projector installation work When installing and using the projector with a method other than floor standing installation using the adjustable feet, insert, for example, spacers (metal) between the projector and installation surface so that there is a gap of about 10 mm to 20 mm to ensure the cabinet does not touch the installation surface. Furthermore, use the screw holes (shown in the figure) for ceiling mounting to fix the projector in place.
Registration of input signal data Registration of new data When a new signal is supplied, press MENU on the remote control or operating section of the main unit. When its data has been registered, the “MAIN MENU” screen is displayed. ▲▼◄► ENTER DEFAULT • The data of 96 input signals can be registered. • The signals supporting the installed input module are input and their data registered.
Registration of input signal data (continued) 4. Use ▲▼◄► to select the characters and numerals one by one, and press ENTER to set them. RENAME NAME SVGA72-A2 MEMORY NO A2 INPUT RGB1 fH 48.08kHz fV 72.17Hz A B C D E F G H I J K H(POS) L M N O SYNC.STATE P Q R S T U V W X Y Z V(POS) ; : , . a b c d e f g h i j k l m n o p q r s t u v w x y z / + - * 0 1 2 3 4 5 6 7 8 9 < > BS OK _ @ [ ] CANCEL 5. Once the name has been changed, press ▲▼◄► to select “OK” and then press ENTER.
2 Details of registered signal 3. Press ENTER. • A “Change registered signals” screen will appear. RENAME NAME SXGA60-A1 MEMORY NO A1 INPUT RGB1 fH 64.00kHz fV 60.00Hz A B C D E F G H I J K H(POS) L M N O SYNC.STATE P Q R S T U V W X Y Z V(POS) ; : , . a b c d e f g h i j k l m n o p q r s t u v w x y z / + - * 0 1 2 3 4 5 6 7 8 9 < > BS OK _ @ [ ] REGISTERED SIGNAL STATUS NAME MEMORY NO INPUT fH fV SYNC.STATE SXGA60-A1 A5 (1-2) RGB1 63.98kHz 60.
Basic operations using the remote control Switching the input signal AUTO SETUP INPUT SELECT SHUTTER ON SCREEN ASPECT TEST PATTERN FUNC1 STATUS LIGHT You can use the remote control to switch the signals that are being input and projected. 1. Press INPUT SELECT on the remote control or the main unit. • Press RGB1: Switches to RGB1 input. • Press RGB2: Switches to RGB2 input. • Press DVI-D: Switches to DVI-D input. • Press VIDEO: Switches to video input. • Press S-VIDEO: Switches to S-VIDEO input.
The automatic setup function can be used to automatically adjust the resolution, clock phase and picture position when analogue RGB signals consisting of bitmap images such as computer signals are being input, or to automatically adjust the picture position when DVI-D signals are being input. (The automatic setup function does not work with video format signals such as signals output from a DVD player.
Basic operations using the remote control (continued) Changing the picture aspect ratio You can change the aspect ratio for projected pictures to match the input signal. 1. Press ASPECT on the remote control. • The setting will change as follows each time ASPECT is pressed. VID AUTO (PRI.) DEFAULT S1 AUTO THROUGH VID AUTO 16:9 HV FIT 4:3 V FIT H FIT Note • Some aspect ratios may not be available for selection depending on the input signal. Refer to “Adjusting the aspect ratio” for details. (p.
On-screen menus MAIN MENU The main menu consists of the following 11 menu items. When a main menu item is selected, the screen changes to a sub-menu selection screen. Icon MAIN MENU item PICTURE MENU POSITION ▲▼◄► ENTER ADVANCED MENU DISPLAY LANGUAGE Basic Operation DISPLAY OPTION PROJECTOR SETUP P IN P TEST PATTERN DEFAULT SIGNAL LIST SECURITY NETWORK Menus are extensively used for configuring, adjusting or reconfiguring the projector. MENU Press to display the MAIN MENU screen.
On-screen menus (continued) POSITION (pp. 58-61) POSITION SHIFT ASPECT ZOOM CLOCK PHASE KEYSTONE ENTER PROJECTOR SETUP (pp. 75-82) DEFAULT 0 MENU SELECT SUB MENU ADVANCED MENU (pp. 62-66) ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION AUTO OFF DEFAULT MENU SELECT CHANGE DISPLAY LANGUAGE (p.
Using the menu screens 1. Press MENU. • The “MAIN MENU” appears on the screen. • For some items, an individual adjustment screen containing a bar scale will appear as shown in the diagram below when ◄► is pressed. MAIN MENU PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION PROJECTOR SETUP P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK ADJUST • If no button is operated for approx. 5 seconds while the individual adjustment screen is displayed, the screen will return to the previous page.
Adjusting the picture Switching the picture mode The user can switch to the desired picture mode suitable for the image source and the environment in which this projector is used. 1. Press ▲▼ to select “PICTURE MODE”. MENU ▲▼◄► ENTER PICTURE PICTURE MODE CONTRAST STANDARD 0 2. Press ◄► to switch “PICTURE MODE”. • The setting will change as follows each time ◄► is pressed. DEFAULT You can adjust pictures to suit your preference. MENU Press to display the MAIN MENU screen. Press to select “PICTURE”.
2. Press ◄► or ENTER. 2. Press ◄► or ENTER. • The “CONTRAST” individual adjustment screen will be displayed. 0 CONTRAST 0 COLOR ADJUST 3. Press ◄► to adjust the level. Operation Adjustment Adjustment range Press ► button. Raises the picture Maximum value brightness and the 31 picture becomes clearer. Press ◄ button. Lowers the picture brightness and weakens the picture. Minimum value -31 3. Press ◄► to adjust the level. Operation Adjustment range Adjustment Press ► button. Deepens colours.
Adjusting the picture (continued) 3. Press ◄► to switch “COLOR TEMPERATURE”. • The setting will change as follows each time ◄► is pressed. DEFAULT USER1 USER2 HIGH MIDDLE LOW • When any setting other than “OFF” has been selected for colour matching, the COLOR TEMPERATURE setting is fixed at “USER1”. • “DEFAULT” cannot be selected when the picture mode has been set to “USER”. Note • All colours will not be displayed properly unless adequate adjustment is made.
Note Sharpness setting • When “FRAME DELAY” is set to “SHORT”, the noise reduction setting function cannot be used. This adjusts the sharpness of the pictures. 1. Press ▲▼ to select “SHARPNESS”. Dynamic iris setting DEFAULT 0 OFF 2. Press ◄► or ENTER. • The “SHARPNESS” individual adjustment screen will be displayed. 0 SHARPNESS Pictures with the optimum contrast will be displayed by automatically providing aperture compensation and signal compensation to suit the pictures concerned. 1.
Adjusting the picture (continued) AUTO IRIS (Automatic aperture adjustment) OFF (No automatic adjustment) 1 (Low) 3 (High) 2 (Intermediate) MANUAL IRIS (Fixed aperture adjustment) OFF (No fixed iris) Setting the system selector This enables the projector to automatically recognize input signals. Furthermore, if unstable signals are input, the system format can be selected manually. 1. Press ▲▼ to select “SYSTEM SELECTOR”. NOISE REDUCTION DYNAMIC IRIS SYSTEM SELECTOR OFF OFF AUTO1 1 (Low) 2.
ET-MD100SD4: When single link SDI signals Select from AUTO YCbCr, 1 080/60i, 1 035/60i, 720/60p, 1 080/24p, 1 080/50i, 1 080/30p, 1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i. When dual link SDI signals Select from AUTO RGB, AUTO X’Y’Z’, 1 920/24p/RGB, 2 048/24p/RGB, 2 048/24p/XYZ, 1 920/24sF/RGB, 2 048/24sF/RGB, 2 048/24sF/ XYZ, 1 920/25p/RGB, 1 920/30p/RGB, 1 920/50i/ RGB, and 1 920/60i/RGB. 7.
Adjusting the position Shift adjustment This function allows the user to adjust the picture position vertically or horizontally if the position of the image projected on the screen is displaced when the projector is properly positioned against the screen. 1. Press ▲▼ to select “SHIFT”. MENU ▲▼◄► ENTER POSITION SHIFT ASPECT DEFAULT 2. Press ENTER. • The “SHIFT” screen will be displayed. SHIFT V H 12 212 3. Press ▲▼◄► to adjust the position.
This changes the aspect ratio of the pictures. 1. Press ▲▼ to select “ASPECT”. SHIFT ASPECT ZOOM DEFAULT 2. Press ◄► or ENTER. • The “ASPECT” individual adjustment screen will be displayed. DEFAULT ASPECT CHANGE 3. Press ◄► to switch “ASPECT”. • The setting will change as follows each time ◄► is pressed. VID AUTO (PRI.) DEFAULT S1 AUTO THROUGH VID AUTO 16:9 HV FIT 4:3 V FIT H FIT • DEFAULT: Pictures are displayed without changing the aspect ratio of the input signals.
Adjusting the position (continued) Adjusting the zoom ratio This adjusts the size of the projected pictures. 1. Press ▲▼ to select “ZOOM”. ASPECT ZOOM CLOCK PHASE DEFAULT Clock phase adjustment • The “ZOOM” screen will be displayed. INTERNAL OFF 100% 100% 100% 3. Press ▲▼ to select “MODE”. 4. Press ◄► to switch “MODE”. • The setting will change as follows each time ◄► is pressed. INTERNAL • When “ASPECT” is set to “THROUGH”, “ZOOM” will not appear.
3. Press ◄► to adjust the correction amount. • The value changes from -127 to 127. 4. Press ▲▼ to select “SUB KEYSTONE” or “LINEARITY”. 5. Press ◄► to adjust the correction amount. • The value changes from -127 to 127. • Adjust the “SUB KEYSTONE” or “LINEARITY” after adjusting the “KEYSTONE”. The variable range of the “SUB KEYSTONE” or “LINEARITY” changes in response to the adjusted value of the “KEYSTONE”.
How to use ADVANCED MENU Digital cinema reality Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied. 1. Press ▲▼ to select “DIGITAL CINEMA REALITY”. MENU ▲▼◄► ENTER ADVANCED MENU DIGITAL CINEMA REALITY BLANKING AUTO 2. Press ◄► or ENTER. • The “DIGITAL CINEMA REALITY” individual adjustment screen will be displayed. DIGITAL CINEMA REALITY AUTO CHANGE 3. Press ◄► to switch “DIGITAL CINEMA REALITY”.
• The “BLANKING” adjustment screen will be displayed. BLANKING UPPER LOWER 0 0 3. Press ▲▼ to select the desired item for adjustment. 4. Press ◄► to adjust blanking. • The adjustment value can be changed within a range of 0 to 384 vertically and 0 to 683 horizontally. When correcting the upper blanking of the screen (top) Press ◄ button to move the blanking zone upward; ► button to downward.
How to use ADVANCED MENU (continued) 2. Press ENTER. • The “CLAMP POSITION” screen will be displayed. CLAMP POSITION POSITION ADJUST 1 3. Press ◄► to adjust. • The value changes from 0 to 255. • The optimal value for the clamp position adjustment If dark areas are crushed: The optimal value is the point where the dark area is best improved. If the dark areas are displayed in green: The optimal value is the point where the green areas become black and the crushing effect is rectified. 4.
10. Press ENTER. • The “BRIGHT ADJUST” screen will be displayed. BRIGHT ADJUST BRIGHT INSIDE BRIGHT OUTSIDE 18. Press ▲▼ to select an item, and press ◄► to adjust the setting. Projection Edge blending width (right) range BRIGHT adjustment (right) 11. Press ▲▼ to select “BRIGHT INSIDE”. Marker 12. Press ENTER. • The “BRIGHT INSIDE” adjustment screen will be displayed.
How to use ADVANCED MENU (continued) 2. Press ◄► to switch “FRAME DELAY”. • The setting will change as follows each time ◄► is pressed. DEFAULT SHORT • DEFAULT: This is the standard setting. • SHORT: This causes the pictures to be delayed after the audio. Note • When “FRAME DELAY” is set to “SHORT”, deterioration in the picture quality will occur. Furthermore, the noise reduction function cannot be used.
Setting the DISPLAY LANGUAGE Changing the display language This lets you switch the on-screen display language. 1. Press ▲▼ to select the desired language. MENU ▲▼◄► ENTER DISPLAY LANGUAGE C ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO 日本語 中文 русский 2. Press ENTER to establish your selection. • Menus, setting items, adjustment screens, and control button names will be displayed in the language the user chooses.
Display Option settings Adjusting colour matching When multiple sets are used simultaneously, this projector allows the user to correct the difference of colours among the sets. 1. Press ▲▼ to select “COLOR MATCHING”. MENU ▲▼◄► ENTER DISPLAY OPTION COLOR MATCHING LARGE SCREEN CORRECTION OFF OFF 2. Press ◄► to switch “COLOR MATCHING”. • The setting will change as follows each time ◄► is pressed. OFF 3COLORS MEASURED DEFAULT This menu can be used to make a variety of picture and projector settings.
• The “3COLORS:RED”, “3COLORS:GREEN” or “3COLORS:BLUE” screen will be displayed. If you selected “7COLORS”, the “7COLORS:RED”, “7COLORS:GREEN”, “7COLORS:BLUE”, “7COLORS:CYAN”, “7COLORS:MAGENTA”, “7COLORS:YELLOW”, or “7COLORS:WHITE” screen will be displayed. 3COLORS:RED RED GREEN BLUE 2048 0 0 6. Press ◄► to adjust the values. • These values can be adjusted from 0 to 2 048.
Display Option settings (continued) 10. Press ENTER. • The “TARGET DATA” screen will be displayed. TARGET DATA RED GREEN BLUE CYAN MAGENTA YELLOW 1/2 x y x y x y x y x y x y 0.64 0.33 0.3 0.6 0.15 0.6 0.225 0.329 0.321 0.154 0.419 0.505 11. Press ▲▼ to select the desired colours, and press ◄► to input their coordinates. 12. After all the data has been input, press MENU. Note • If “709MODE” has been selected as the “COLOR MATCHING” setting, the 3 primary colours defined by the ITU-R BT.
• EDID1 (Input signal formats supported) : Mainly select this when an external device (DVD player, etc.) for outputting video signals of a moving image system is connected to DVI-D IN. • EDID2 (Input signal formats supported) : Mainly use this when an external device (PC, etc.) for outputting video signals of a still image system is connected to DVI-D IN. 4. Press ◄► to switch “DVI SIGNAL LEVEL”. • The setting will change as follows each time ◄► is pressed. 0-255:PC 8.
Display Option settings (continued) AUX DVI IN (Only when the ET-MD77DV is installed) Change this setting if video does not display normally when the ET-MD77DV and an external device are connected via DVI-D. 1. Press ▲▼ to select “AUX DVI IN”. DVI-D IN AUX DVI IN AUX SDI IN • The “AUX DVI IN” screen will be displayed. EDID1 0-255:PC 3. Press ◄► to switch “AUX DVI EDID”. • The setting will change as follows each time ◄► is pressed.
z SDI SIGNAL LEVEL z OSD DESIGN Select the amplitude for the signals to be input. This is only valid when YPBPR and RGB input of HD-SDI. The setting will change as follows each time the button is pressed. • 64-940: Normally set this. • 4-1019: Set this when gray appears black. On-Screen display setting The user can specify the on-screen display. 1. Press ▲▼ to select “ON-SCREEN DISPLAY”. AUX SDI IN ON-SCREEN DISPLAY BACK COLOR BLACK 2. Press ENTER. • The “ON-SCREEN DISPLAY” screen will be displayed.
Display Option settings (continued) 2. Press ◄► to switch “BACK COLOR”. • The setting will change as follows each time ◄► is pressed. BLACK LOGO3 BLUE LOGO1 LOGO2 • BLACK: The entire projection area will appear black. • BLUE: The entire projection area will appear blue. • LOGO1: The picture registered by the user will be projected in the projection area. • LOGO2: The picture registered by the user will be projected in the projection area. • LOGO3: The Panasonic logo is projected.
Projector setup Setting a projector ID The projector has an ID number setting function that helps the user to control two or more projectors either simultaneously or separately with a single remote control. The ID number is set to “ALL” by default. Hence the ID number need not be set when only one projector is used. MENU ▲▼◄► ENTER 1. Press ▲▼ to select “PROJECTOR ID”. PROJECTOR SETUP PROJECTOR ID INSTALLATION 1/2 ALL FRONT-FLOOR 2. Press ◄► to switch “PROJECTOR ID”.
Projector setup (continued) Installation Setting A projection scheme can be chosen depending on the installation of the projector. If the picture is shown upside down or in reverse, change the projection scheme. • Select the setting by displaying the on-screen indications using buttons of the remote control or the control panel on the main unit. 1. Press ▲▼ to select “INSTALLATION”. PROJECTOR ID INSTALLATION ALTITUDE MODE ALL FRONT-FLOOR ON 2. Press ◄► to switch “INSTALLATION”.
This lets you switch the four light source lamps to one of four brightnesses in accordance with the operating conditions and purpose of use. 1. Press ▲▼ to select “LAMP SELECT”. DIRECTION LAMP SELECT LAMP RELAY HORIZONTAL QUAD OFF 2. Press ◄► to switch “LAMP SELECT”. • The setting will change as follows each time ◄► is pressed. TRIPLE QUAD DUAL L1 SINGLE L2 L2/L3/L4 L3 L1/L3/L4 L4 L1/L2/L4 L1/L4 L1/L2/L3 L2/L3 • “QUAD” : The four lamps illuminate. • “L1” : One lamp illuminates.
Projector setup (continued) 2. Press ENTER. Lamp relay • The “RS-232C” screen will be displayed. If using the projector for a continuous period of 24 hours or more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use. • “LAMP RELAY” will only be enabled when the lamp selection is “SINGLE” (1 lamp), “DUAL” (2 lamps), “TRIPLE” (3 lamps) or “QUAD” (4 lamps). 1. Press ▲▼ to select “LAMP RELAY”.
Displays the status of the projector. 1. Press ▲▼ to select “STATUS”. REMOTE2 MODE STATUS AIR FILTER CLEANING DEFAULT 2. Press ENTER. • The “STATUS” screen will be displayed. STATUS INPUT NAME SIGNAL FREQUENCY PROJECTOR RUNTIME LAMP1 LAMP2 LAMP3 LAMP4 INTAKE AIR TEMP. OPTICS MODULE TEMP. AROUND LAMP TEMP. REMOTE2 STATUS 1/3 RGB2 XGA60-A399999 48.36kHz/59.99Hz 76h 341h / ON / 334h / ON / 342h / ON / 97h / ON / 31°C/87°F 27°C/80°F 31°C/87°F DISABLE 3. Press ◄► to move to the next page.
Projector setup (continued) 2. Press ENTER. • The “AIR FILTER CLEANING” screen will be displayed. • You can select the automatic cleaning time (“TIME”) and also force cleaning to be carried out immediately (“EXECUTE”). AIR FILTER CLEANING TIME EXECUTE 00:00 3. Press ▲▼ to select “TIME”. • Select “TIME” and then set the time for automatic cleaning to be carried out. • If you would like cleaning to be carried out straight away, select “EXECUTE” and then press ENTER. 4. Press ◄► to switch “TIME”.
4. Press ◄► to switch “TIME ZONE”. Setting FUNC1 The user can specify the function of the “FUNC1” button on the remote control. 1. Press ▲▼ to select “FUNC1”. 6. Press ENTER. DISABLE • The “ADJUST CLOCK” screen will be displayed. 2. Press ENTER. ADJUST CLOCK YEAR MONTH DAY HOUR MINUTE APPLY • The “FUNC1” screen will be displayed. FUNC1 DISABLE C P IN P 3. Press ▲▼ to select a function. • DISABLE: Disables the FUNC1 button.
Projector setup (continued) Load all user data This loads various setting values that were saved as a backup to the internal memory of the projector. 1. Press ▲▼ to select “LOAD ALL USER DATA”. SAVE ALL USER DATA LOAD ALL USER DATA INITIALIZE 2. Press ENTER. • The “SECURITY PASSWORD” screen will be displayed. SECURITY PASSWORD 3. Enter the password set for the security password of the security menu. • A confirmation screen will appear.
P IN P Using the P IN P function Two videos can be projected simultaneously by placing a separate small sub screen within the main screen. 1. Press ENTER. • The “P IN P” screen will be displayed. MENU P IN P P IN P MODE ▲▼◄► ENTER OFF 2. Press ▲▼ to select “P IN P MODE”. P IN P MODE OFF C USER1 USER2 USER3 3. Press ▲▼ to select a function. • OFF: The P IN P function is not used. • USER1, USER2, USER3: The P IN P function is used with the settings that were set in “Setting the P IN P function”. 4.
P IN P (continued) • MAIN WINDOW: The input terminal for the main window is displayed. Press ▲▼ to select an item, and press ENTER to switch to the item. SIZE: The user can specify the display size of the main window between 10 % and 100 %. POSITION: The user can specify the display position of the main window on the screen. • SUB WINDOW: The input terminal for the SUB WINDOW is displayed. Press ▲▼ to select an item, and press ENTER to switch to the item.
Displaying the internal test pattern Test pattern Results of adjustment on the image, picture quality, position, size and other factors will not be reflected in test patterns. Be sure to display the input signal before performing various kinds of setting. 1. Press ◄► to search through the various types of test patterns. MENU ▲▼◄► ENTER Cycle of displayed internal test patterns The setting will change as follows each time ◄► is pressed.
Setting the security Displaying the security screen Password settings and text settings can be made after the security screen is displayed. z If using for the first time MENU ▲▼◄► ENTER 1. Press ▲, ►, ▼, ◄, ▲, ►, ▼ and ◄ in this order. z If the existing password has been changed Enter the new password. SECURITY PASSWORD 2. Press ENTER. • The “SECURITY” screen will be displayed.
Changing the security password The password can be changed. 1. Press ▲▼ to select “SECURITY PASSWORD CHANGE”. SECURITY PASSWORD SECURITY PASSWORD CHANGE DISPLAY SETTING OFF OFF • OFF: The text display is disabled. • TEXT: The text display is enabled. • LOGO1: The picture registered by the user will be projected. • LOGO2: The picture registered by the user will be projected. • LOGO3: The Panasonic logo is projected. Note 2. Press ENTER. • The “SECURITY PASSWORD CHANGE” screen will be displayed.
Setting the security (continued) Control device setup Control from the remote control and main unit controls can be restricted. 1. Press ▲▼ to select “CONTROL DEVICE SETUP”. DISPLAY SETTING TEXT CHANGE CONTROL DEVICE SETUP OFF 2. Press ENTER. • The “CONTROL DEVICE SETUP” screen will be displayed. CONTROL DEVICE SETUP CONTROL PANEL REMOTE CONTROLLER 3. Press ▲▼ to select “CONTROL PANEL” or “REMOTE CONTROLLER”. • CONTROL PANEL: Restriction of control from the main unit controls can be set.
How to use network function Network standby When the projector is in a standby state, you can control the power of the projector from a computer connected via a wired LAN. 1. Press ▲▼ to select “NETWORK STANDBY”. MENU ▲▼◄► ENTER NETWORK NETWORK STANDBY NETWORK SETUP OFF 2. Press ◄► to switch “NETWORK STANDBY”. • The setting will change as follows each time ◄► is pressed. OFF DEFAULT ON • ON: Enables the network standby function. • OFF: Disables the network standby function.
How to use network function (continued) • DHCP (DHCP client function) : Set the DHCP item to ON when to acquire an IP address automatically using the DHCP server. Set to OFF if DHCP server is not used. Enter the IP address if DHCP server is not used. • IP ADDRESS (Display of IP address and setting) : Enter the IP address if DHCP server is not used. • SUBNET MASK (Displaying and setting the subnet mask) : If not using a DHCP server, enter the subnet mask.
Network connections The projector is equipped with network functions, and web browser controls can be used to carry out the following operations from a computer. • Projector settings and adjustments • Projector status display • Transmission of E-mail messages if there is a problem with the projector Note • A LAN cable is required to use the network function. PC Projector LAN cable (straight) • • • • A Web browser is required to use this function. Make sure that a Web browser is available in the system.
How to use network function (continued) Accessing from the Web browser 1. Activate the Web browser in the personal computer. 2. Enter the IP address set by the projector into the URL input field of the Web browser. 3. Enter your “User Name” and “Password”. Factory Settings User name: Password: user1 (user privileges) admin1 (administrator privileges) panasonic (lowercase) 4. Press OK to display the Projector status page.
Basic control page This page is the first page displayed when the projector is accessed through a web browser. To move from another page, click [Projector control], then [Basic control]. Page selection tabs Click these to switch pages. This displays the on-screen status. It is displayed even if the on-screen display of the projector is set to off. Monitor information button Click this item, and the status of the projector is displayed.
How to use network function (continued) Detail control page Click [Projector control], then [Detail control] to display the Detail control page. Pressing these buttons controls the projector and updates the on-screen description on the right of the control page when control is finished. Lens adjustment Test pattern display This button updates the on-screen description on the right of the control page with the latest information.
Error information page When is displayed on the status information screen, click it to display the error details. • Depending on the nature of the error, the projector may be placed in the standby mode for its own protection. OK: Normal operation FAILED: Occurrence of trouble z When [FAILED] has appeared for an item Description Trouble has occurred in the microcomputer circuitry. Consult your dealer. FAN Trouble has occurred in the fan or its drive circuit. Consult your dealer.
How to use network function (continued) E-mail setup page With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be sent to one or more preset e-mail addresses (maximum two addresses). Click [Detailed set up], then [E-mail set up] to display the E-mail setup page. Select “Enable” to use the E-mail function. Enter the IP address or server name of the E-mail server (SMTP). The DNS server must be set if the server name is entered.
Special Features Periodic warning interval setting (E-mail is sent on the checked days of the week/times) ENGLISH – 97
How to use network function (continued) E-mail setup page (continued) Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be used. Do not enter it when the second E-mail address is not going to be used. Select the conditions for sending E-mail to the second E-mail address. MAIL CONTENTS: Select “NORMAL” or “SIMPLE”. ERROR: an error is detected by self-diagnosis. LAMP1 RUNTIME: remaining lamp service time has reached the value set in the field.
Authentication set up page The POP server is set on this page when POP authentication is required for mail transmissions. Click [Detailed set up], then [Authentication set up] to display the POP server setup page. Select the authentication method specified by your Internet service provider. Set this if SMTP authentication has been selected. POP server name field Available input characters: Alphanumeric characters (A–Z, a–z, 0–9), hyphen (-), period (.
How to use network function (continued) Contents of mail sent z Mail with the contents shown below is sent when the E-mail settings have been established.
Adjust clock page Click [Detailed set up], then [Adjust clock] to display the Adjust clock page. Time zone selection Button to update time zone setting New date field New time field Button to update time and date settings Note • If the time becomes incorrect immediately after setting the correct time, then the battery needs to be changed. Contact the dealer where you bought the projector to have the battery changed.
How to use network function (continued) Firmware update page (The firmware should be updated only by an individual with the specialized knowledge required to do this.) Enter here the filename of the firmware to be updated. After entering the filename, press the [Upload] button. Data transfer is now commenced. It will take several dozen seconds for the data to be transferred. The time taken will differ depending on the network conditions. Displays the current version. Displays the updated version.
Using the PJLink™ protocol The network function of the projector supports PJLink™ class 1, and the PJLink™ protocol can be used to perform projector setting and projector status query operations from a PC. Supported commands The following table lists the PJLink™ protocol commands that can be used to control the projector.
Using the serial terminals The main unit is equipped with SERIAL terminals located in its connection terminals, and this terminal is compliant with RS-232C/RS-422. Also a serial output terminal is provided to enable plural projector control.
For RS-422 z Single projector D-Sub 9-pin (female) PC RS-232C IN RS-422 IN SERIAL RS-422 OUT Connection terminals on projector D-Sub 9-pin (male) Communication cable (straight) z Plural projectors D-Sub 9-pin (female) PC RS-232C IN D-Sub 9-pin (male) RS-422 IN SERIAL RS-422 OUT D-Sub 9-pin (female) RS-232C IN RS-422 IN SERIAL Connection terminals on projector 1 D-Sub 9-pin (male) RS-422 OUT Connection terminals on projector 2 D-Sub 9-pin (male) D-Sub 9-pin (female) D-Sub 9-pin (male) Com
Using the serial terminals (continued) Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control.
Cable specifications Connecting to a PC z For RS-232C Computer (DTE specifications) Projector 1 NC NC 1 2 2 3 3 4 NC NC 4 5 5 6 NC NC 6 7 7 8 8 9 NC NC 9 When multiple projectors are connected 2nd (RS-422 IN) 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 Attention • To connect the computer to the SERIAL terminal, prepare an adequate communication cable that fits to your personal computer.
Using the Remote 2 terminal Using the REMOTE 2 terminal provided on the connection terminals of the main unit, it is possible to operate the projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be received.
Indication of monitor lamp Five monitor lamps are provided at the top of main unit front to inform the user of the lamp replacement time and unusual internal temperature. These lamps indicate the degree of abnormality by combination of blinking and/or lighting lamps. Turn off the power and take the proper measure according to the table below.
Cleaning and replacement of air filter If the air filter is blocked with too much dust, the inside of the projector will become hot and the temperature monitor (TEMP) indicator will flash and the power will turn off. The static electric mesh filter should be replaced and the metal mesh filter and brush inside the filter unit should be cleaned after approximately 2 000 hours of use, although this is a guide only and the actual time will vary depending on the operating conditions. Procedure of cleaning 1.
7. Install the movable metal mesh filter to the filter cleaning unit. Movable metal mesh filter • When reassembling, align the edge of the movable metal mesh filter with position A. • Hook the movable metal mesh filter onto the gear and the rail. • The movable metal mesh filter will be set to the correct position after the set is installed and the power is turned on, so it can be installed in the middle position during reassembly without any problem. 8.
Replacement of lamp unit WARNING • • • • Wait until the lamp is cooled sufficiently before replacing the lamp unit. Make sure that all four lamp units are installed. Replacement of the lamp unit should be carried out by a qualified technician. Do not remove any screws (such as the black screws) other than those indicated when replacing the lamp unit. If this is not observed, electric shocks, burns or other injuries may occur.
Procedure of lamp unit replacement 1. Turn the main power OFF, following the procedures described in “Powering up the projector” (p. 36) and “Powering off the projector” (p. 37), disconnect the power plug from the AC power source, and wait for one hour or more. Then check around the lamp unit that has cooled down. 2. Use a Phillips screwdriver to loosen the lamp unit cover screw at the rear of the projector until the screw turns freely. Lamp unit cover screw 3.
Notes when installing the ceiling mount bracket When installing the ceiling mount bracket to the projector, install the accessory eye bolts and wires to the projector. (The projector will still be safe if they are not used, however they will help prevent the possibility of accidents caused by the projector falling down if the screws happen to become loose.) Installation should be carried out by a qualified technician by following the procedure given below.
Symptoms … try to check the following points again.
Self-diagnosis display There is a self-diagnosis display located on the side of the projector (p. 15) for automatically displaying the corresponding details when an error or warning occurs. Self-diagnosis display Details Remedy U04 Air filter is blocked • Clean the air filter unit. U11 Intake air temperature warning U12 Optical module temperature warning U13 Lamp ambient temperature warning • Check whether there is sufficient space around the projector. • The ambient temperature is too high.
Details F41 Lamp 1 memory error F42 Lamp 2 memory error F43 Lamp 3 memory error F44 Lamp 4 memory error F61 Ballast 1 communication error F62 Ballast 2 communication error F63 Ballast 3 communication error F64 Ballast 4 communication error F80 Resize IC setting error F81 FM-R test error F82 FM-G test error F83 FM-B test error F91 FPGA1 configuration error F92 FPGA2 configuration error F93 Flash ROM error F94 RAM error F95 FPGA expansion error F96 Lens shift error FE1 Po
Specifications Model No. Power supply PT-DW100E 220 V – 240 V, 50 Hz/60 Hz Power consumption 1 500 W (about 15 W in standby) Amps 9.5 A Panel size ® DLP Chip Display system Number of pixels 0.85 inch (aspect ratio 16:9) Three-unit DLP® chip, DLP® type 3 × 1 049 088 pixels (1 366 × 768 dots) Lens (Powered zoom/ Powered focus control) Projection lamp *1 Optical output For video signal (S-video included) For RGB signal Option 4 bulbs × 300 W UHM lamp 10 000 lm (ANSI) Horizontally 15.75 kHz/15.
Model No. RGB2 input terminal Video input/output terminal S-video input terminal Interface ports PT-DW100E 1 set of high-density, D-sub 15p (female) [For YPBPR input] Y: 1.0 V [p-p] synchronization signal included, PBPR: 0.7 V [p-p] 75 Ω [For RGB input] 0.7 V [p-p] 75 Ω For G-SYNC: 1.
Appendix Compatible Signals The following table specifies the types of RGB/YPBPR/DVI-D signals compatible with the projector. RGB signals can also be input within the range of fH=15 kHz–100 kHz, fV=24 Hz–120 Hz, dot clock=20 MHz–162 MHz. DVI-D signals can also be input within the range of dot clock=25 MHz -162 MHz. Display mode Number of displayed dots Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) Plug and play Format RGB2 DVI-D DVI-D EDID1 EDID2 NTSC/NTSC4.
Display mode Number of displayed dots Scanning frequency Plug and play Dot clock frequency (MHz) Format H (kHz) V (Hz) 1 152 × 870 68.7 75.1 100 RGB/DVI 1 280 × 768 39.6 49.9 65.3 RGB/DVI 1 280 × 768 47.8 59.9 79.5 RGB/DVI 1 280 × 800 41.3 50 68 RGB/DVI 1 280 × 800 49.7 59.8 83.5 RGB/DVI 1 280 × 960 60 60 108 RGB/DVI 1 280 × 1 024 52.4 50 88 RGB/DVI 1 280 × 1 024 64 60 108 RGB/DVI 1 280 × 1 024 72.3 66.3 125 RGB/DVI 1 280 × 1 024 78.2 72 135.
Appendix (continued) List of P IN P RGB1 Subwindow RGB2 DVI S-VIDEO input Moving image system*3 RGB system*4 ○ ○ ○ ○ × × ○ × ○ ○ ○ ○ YPbPr input RGB input YPbPr input RGB input × × × × YPbPr input × × × × × RGB input × × × × ○ RGB1 RGB2 ET-MD77DV VIDEO input RGB input Main window AUX ETET-MD77SD3/ MD77SD1 ET-MD100SD4*1 ○ Moving image *2 system RGB system*4 ○ ○ × × ○ ○ ○ ○ ○ × × × × × × × ○ × × × ○ VIDEO input ○ × ○ × × × × ○ × ×
Dimensions Outside dimensions 320 643 unit : mm OPEN FILTER CLEANING ON CLOSE MAIN POWER 578 Information OFF AC IN ENGLISH – 123
Index Be sure to read the “IMPORTANT SAFETY NOTICE” and the “Precautions with regard to safety”. (pp.
R Raster position ･･･････････････････････････････ 66 Registered signals ････････････････････････････ 43 Registering the picture mode settings as presettings ･･････････････････････････････ 56 Remote2 mode ･･･････････････････････････････ 78 Remote 2 terminal ･･･････････････････････････ 108 RGB IN ･･････････････････････････････････････ 70 RS-232C setting ･･････････････････････････････ 78 S Save all user data ･････････････････････････････ 81 SD-SDI input module･･････････････････････････ 31 Self-diagnosis displ
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/ EC and 2006/66/EC.
