User Guide
Table Of Contents
- TABLE OF CONTENTS
- IMPORTANT SAFETY NOTICE
- PRECAUTIONS WITH REGARD TO SAFETY
- CAUTION
- ACCESSORIES
- PRECAUTIONS ON HANDLING
- NAME AND FUNCTION OF PARTS
- USING THE REMOTE CONTROL UNIT
- INSTALLATION
- CONNECTION
- HOW TO INSTALL AND REMOVE THE PROJECTION LENS (OPTIONAL)
- PROJECTION
- HOW TO ADJUST THE LENS
- AUTOMATIC ADJUSTMENT (AUTO SETUP)
- USING THE FREEZE FUNCTION
- USING THE SHUTTER FUNCTION
- USING THE DIGITAL ZOOM (-D.ZOOM+) FUNCTION
- ON-SCREEN MENUS
- ADJUSTING THE PICTURE
- ADJUSTING THE POSITION
- HOW TO USE ADVANCED MENU
- ADJUSTING THE AUDIO
- CHANGING THE DISPLAY LANGUAGE
- OPTION 1 SETTINGS
- OPTION 2 SETTINGS
- DISPLAYING THE INTERNAL TEST PATTERN
- SETTING THE SECURITY
- SETTING THE NETWORK
- CONNECTING THE PC
- USING THE SERIAL TERMINALS
- USING THE REMOTE 2 TERMINAL
- INDICATION OF LAMP MONITOR
- CLEANING AND REPLACEMENT OF AIR FILTER
- REPLACING THE LAMP UNIT
- USING WEB BROWSER CONTROL
- USING THE PJLINK tm PROTOCOL
- BEFORE ASKING FOR SERVICE
- SPECIFICATIONS
- COMPATIBLE SIGNAL LIST
- PROJECTION DISTANCES BY PROJECTION LENS
- DIMENSIONS
- FRANCAIS INFORMATION
18
Connection
Setup precautions
• Before connecting any of your video/audio equipment to the projector, carefully read the owners manual
supplied with the equipment once again.
• All cable connections should be made with the entire system devices, including the projector, first turned off.
• Obtain commercial interconnecting cables for devices supplied with no accessory or optional interconnect
cables.
• Video signals containing too much jitter may cause the images on the screen to randomly wobble or shake.
Inserting a time base corrector (TBC) in the projector’s video line will relieve this problem.
• The projector only accepts composite-video, S-video, analog-RGB (with TTL sync. level), and digital signal
from PC.
• Some PC models are not compatible with the PT-D3500U projector.
• The pin assignments on the S-VIDEO IN port are as
follows:
• The pin assignments on the DVI-D input port are as
follows (interface with DVI-D output port on PC):
• The pin assignments on the RGB2 input port are as
follows:
Viewed from mating side
Pin No.
Signal
Ground (luminance)
Ground (color)
Luminance signal
Color signal
Pin : Not used.
Pins - , and : Ground.
Pins and : Valid if the PC has the
corresponding function.
Viewed from mating side
Signal
R/P
R
G/G · SYNC/Y
B/P
B
SDA
HD/SYNC
VD
SCL
Pin No.
Viewed from mating side
Pin No.
Signal
T. M. D. S data 2-
T. M. D. S data 2+
T. M. D. S data 2/4
shield
T. M. D. S data 4-
T. M. D. S data 4+
DDC clock
DDC data
T. M. D. S data 1-
T. M. D. S data 1+
T. M. D. S data 1/3
shield
T. M. D. S data 3-
Signal
T. M. D. S data 3+
+5 V
Ground
Hot plug sense
T. M. D. S data 0-
T. M. D. S data 0+
T. M. D. S data 0/5
shield
T. M. D. S data 5-
T. M. D. S data 5+
T. M. D. S clock
shield
T. M. D. S clock+
T. M. D. S clock-
Pin No.
• The DVI-D input terminal supports single link only.
• EDID settings should be performed to suit the DVI
equipment being connected. (Page 34)
• The DVI-D input terminal can be used to connect to a
DVI equipment, but note that images may not appear
or the projector may not work properly when
connected to certain DVI equipment.