Specification Sheet

ManualsBrandsPanasonic ManualsProjection TVPT-D12000U

< 1 >

S PEC F ILE

Product Number : PT-D12000

Product Name : 3-Chip DLP™ Projector

As of July 2008. Appearance and specifications are subject to change without notice.

Summary of content (12 pages)

PAGE 1
S P E C P ro d u c t N u m b e r : PT-D12000 P ro d u c t N a m e : 3-Chip DLP™ Projector F I L E As of July 2008. Appearance and specifications are subject to change without notice.
PAGE 2
S P E C F I L E PT-D12000 3-Chip DLP™ Projector Specifications Main Unit Power supply: North America: 120–240 V AC, 16 – 9.0 A, 50/60 Hz (3-wire single-phase) Europe, Asia 220–240 V AC, 9.5 A, 50/60 Hz (3-wire single-phase) Power consumption: North America: 1,600–1,500 W (10-15 W in standby mode with fan stopped) Europe, Asia 1,500 W (15 W in standby mode with fan stopped) DLP™ chip: Panel size: 0.
PAGE 3
S P E C F I L E PT-D12000 3-Chip DLP™ Projector RGB2 IN: D-sub HD 15-pin x 1 R, G, B: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms HD, VD, SYNC: TTL, high impedance, positive/negative automatic VD: 1.4–5.0 Vp-p, positive/negative automatic, 75 ohms Y, PB, PR Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals. VIDEO IN: BNC x 1, 1.0 Vp-p, 75 ohms VIDEO OUT: BNC x 1, 1.
PAGE 4
S P E C F I L E PT-D12000 3-Chip DLP™ Projector Operating temperature*8: 0°C–45°C (32°F–113°F) Operating humidity: 10%–80% (no condensation) Remote Control Unit Number of functions: 35 keys, 39 functions Power supply: 3 V DC (AA battery x 2) Operation range*9: Approx. 30 m (98.4´) when operated from directly signal receptor Dimensions (W x H x D): 51 x 22.7 x 176 mm (2˝ x 7/8˝ x 6-15/16˝) Weight: 134 g (4.
PAGE 5
S P E F C I L E PT-D12000 3-Chip DLP™ Projector Shape of the plug receptacle PT-D12000U PT-D12000E 125 V AC, 20 A (NEMA 5-20R) 250 V AC, 15 A (NEMA 6-15R) Note: 220-240V AC, 16 A 220-240V AC, 13 A/15 A Be sure to use the power plug adaptor cord supplied with the projector. The supplied power plug adaptor can be used with the PT-D12000 only.
PAGE 6
S P E F C I L E PT-D12000 3-Chip DLP™ Projector Standard setting-up positions 416.5– 536.5 (16-13/32˝– 21-1/8˝) *1 When the lens protrudes to the maximum. 163 L *1 Projected image 414 mm (16-5/16˝) with the ET-D75LE6 316.5 mm (12-15/32˝) with ET-D75LE1 301 mm (11-27/32˝) with the ET-D75LE2 304.5 mm (12˝) with the ET-D75LE3 328.4 mm (12-15/16˝) with the ET-D75LE4 456.5 mm (17-31/32˝) with the ET-D75LE8 404.
PAGE 7
S P E F C I L E PT-D12000 3-Chip DLP™ Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance.
PAGE 8
S P E F C I L E PT-D12000 3-Chip DLP™ Projector List of compatible signals This projector supports RGB signals with horizontal frequencies of 15 to 100 kHz, vertical frequencies of 24 to 120 Hz and dot clock frequencies of 20 MHz to 162 MHz. NOTE: The native resolution of this projector is 1,400 x 1,050 pixels.
PAGE 9
S P E F C I L E PT-D12000 3-Chip DLP™ Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names No. Signal name Description No.
PAGE 10
S P E C F I L E PT-D12000 3-Chip DLP™ Projector Cable specifications Projector 1 PC (DTE) NC NC 3 3 4 NC NC 4 5 5 6 1 2 2 NC NC 6 7 7 8 8 9 NC NC 9 Control commands Command : Parameter Function PON POF IIS:RG1 IIS:RG2 IIS:VID IIS:SVD IIS:DVI IIS:AUX LPM:0 LPM:1 LPM:2 LPM:3 LPM:4 LPM:5 LPM:6 LPM:7 LPM:8 LPM:9 LPM:10 LPM:11 LPM:12 LPM:13 OSH:1 OSH:0 OPP:0 OPP:1 OPP:2 OPP:3 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA OTE:0 OTE:1 OTE:2 OTE:4 OTE:9 OTE:10 TSD:y1y2y3y4m1m2d1d2w
PAGE 11
S P E C F I L E PT-D12000 3-Chip DLP™ Projector Status asking commands Command : Parameter QPW Function Main power status QSH Shutter function status QIN Input signal status QOS On-screen display status QST Q$L:p1 Q$L:p2 Q$L:p3 Q$L:p4 QSL Projector run time Lamp 1 run time Lamp 2 run time Lamp 3 run time Lamp 4 run time Lamp operation mode status QIB Optional board slot status QPP P in P status QGD QGT Date setting status Time setting status Callback 001 000 1 0 RG1 RG2 VID SVD DVI
PAGE 12
S P E F C I L E PT-D12000 3-Chip DLP™ Projector Notes on Projector Placement and Operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s exhaust openings. 3.