ORDER NO. VED1209447CE D10 LCD Projector Model No. PT-AE8000U PT-AT6000E PT-AE8000EA PT-AE8000EH PT-AE8000EZ © Panasonic Corporation 2012. Unauthorized copying and distribution is a violation of law.
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual. WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians.
TABLE OF CONTENTS ■ COVER PAGE 1. Safety Precautions 2. Specifications ■ SECTION 1 1. The name of each part 2. OSD Menu Navigation 3. Extend mode (EXT OPTION menu) 4. External Control 5. Notification for service operation 6. Troubleshooting ■ SECTION 2 1. Parts Location 2. Disassembly Instructions ■ SECTION 3 1. Adjustment items and procedure 2. Microprocessor update procedure ■ SECTION 4 1. Block Diagram 2.
1. Safety Precautions 1.1. General Guidelines - For continued safety, no modification of any circuit must be attempted. - Unplug the power cord from the power outlet before disassembling this projector. - Use correctly the supplied power cord and must ground it. - It is advisable to use an isolation transformer in the AC power line before the service. - Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed and the power supply turned ON.
2. Specifications *1 : Measurement, measuring conditions and method of notation all comply with ISO21118 international standards. *2 : For details of video signals that can be projected using this projector, refer to “List of compatible signals” of Operating Instructions.
*1 : HD/SYNC, and VD terminals do not accept tri-level sync signals. *2 : Average value. Weight varies for each product..
SECTION 1 < Service Information > Model No. PT-AE8000U PT-AT6000E PT-AE8000EA / AE8000EH / AE8000EZ CONTENTS 1. The name of each part ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-2 1.1. Projector body 1.2. Control panel 1.3. Rear terminals 1.4. Remote control 2. OSD Menu Navigation ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3.Extend mode (EXT OPTION menu) ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-4 INF-6 3. 1. Procedure to open / close "EXT OPTION" menu 3. 2.
1. Name and function 1.1.
1.2. Control Panel 1.3. Rear terminals 1.4.
2.
MENU MENU (2/2) Note : The default settings may be different depending on the picture menu INF - 5
3. Extend mode (EXT OPTION menu) This projector has extend mode "EXT OPTION" menu in addition to standard on-screen menus. This mode has Self-Check function, Test Pattern and other functions for Service. 3. 1. Procedure to open / close "EXT OPTION" menu. 1. When the projector is power ON, press "POWER" button on the main unit or remote control unit to display "POWER OFF" confirmation screen. 2. Press the " " button to select "CANCEL" in the "POWER OFF" confirmation screen. 3.
(17)- Rotation check of Exhaust fan and Power fan (Displays "NG" when Fan is abnormal condition) * When detected abnormal temperature around the air intake port / air exhaust port / LCD block, TEMP indicator turned on. If arriving at the critical temperature, the power supply will shut down automatically (thermal shutdown) and the indicator will flash.
4. External Controls of SERIAL Connection The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connecter. 4. 1. Connecting exsample Interface at the rear side Computer D-Sub 9p (Male) Note Interface cable is not a standard accessory. Please purchase locally. 4. 2.
4. 5. Basic format Data streaming from the computer will start with STX, and proceed to command, parameter and end with ETX. Parameters can be added as necessary. STX Command ： Parameter ETX Start byte(02h) 3 bytes 1 byte 1byte - 4 bytes End (03h) ・The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending the command.
4. 7. Inquiry commands Refer to Operating Instructions of PT-AE8000 / PT-AT6000.
5. Notification for service operation 5. 1. Before service operation 5. 1. 1. LCD panel 1. The display unit of this projector comprises three LCD panels. Although an LCD panel is a product of high precision technology, some of the pixels on the projected image may be missing or constantly lit. Please note that this is not a malfunction. 2. Displaying a still image for a longer time may result in an after-image on the LCD panels.
5. 2. Service 5. 2. 1. Supporting Methods The basic service policy is shown below. Service method Applied parts ・ Analyses block (* Specified components are replaced) Block replacement P.C.Board replacement Individual parts supply. Individual parts replacement on ・ Optical Block (with projection lens) *Projection lens can not be separated from optical block. ・ K1/K2-P.C.Board (*Specified components are replaced) ・ P-P.C.Board ・ B-P.C.Board ・ H-P.C.Board ・ M1/M2/M3-P.C.
5. 3. 2. Replacement procedure for lamp unit 1. Confirm that the lamp unit is cooled down completely. (More than 1 hour has passed after main power is off.) 2. Open the top cover in the direction of the arrow. 3. Lamp cover fixing screw is loosened all the way and remove "Lamp cover". Top cover Lamp cover fixing screws lamp cover 4. Use a Phillips screwdriver to unscrew the lamp unit fixing screws (2 screws) until loose. 5.
5. 3. 4. Air filter unit maintenance 1. If too much dust accumulates in the air filter the internal temperature of the projector cannot be maintained at the normal level. 2. Confirmation message is displayed on the screen, and at the same time illuminates red. The power is cut off automatically after a while. 5. 3. 5. Cleaning procedure for Air filter unit 1. Using a Phillips screwdriver to turn the fixing screw of the air filter cover until loose and remove the cover.
6. Troubleshooting 6. 1. Summary of shut down system When the abnormality of the lamp and the abnormality of the fan occurred, possess a shut down function to make a standby state for safety promptly.
6. 2. Troubleshooting flow * The letters in the left of inspection items indicate the P.C. Boards or Modules related to their respective descriptions. * Inspection should be done with "ON" to interlock switch. (inter lock detection) Push the interlock switch to the ON state, and paste the adhesive tape. The projector does not become standby mode. (The power indicator does not illuminate red.) NO Confirm the power supply is 90 V - 264 V AC. Check the power supply.
The projector does not change from standby mode to an operating mode. (The power indicator does not change from red to green.) Confirm every connector (especially, A5) is connected and the lamp unit cover is installed properly. NO Connect the connectors or install the lamp cover properly. YES A Connector A5 pin 14 changes from Low to Hi. NO A Check the connector A5(pin 14) and around them. (Q1019, C1201, R1313) A ・A short has occurred in terminals 1(+3.3V)-4 Check R1558,C1204 (3.
Lamp does not turn ON (LAMP indicator not lit) Check each cable connection. Check for loose screws of lamp unit fixing. NG Connect properly. Tighten the lamp unit fixing screws (2 screws). OK NG When turn on the power, Does the rotation of each fan? A Check IC1017 and around them. Check fan connector. If the connection is properly and the fan is not rotated, replace it. OK After keeping MAIN POWER in OFF condition for 3 minutes or more, turn ON the MAIN POWER and press POWER button.
Lamp does not turn ON (LAMP indicator is lit) After keeping MAIN POWER in OFF condition for 3 minutes NG or more, turn ON the MAIN POWER and press POWER button. Then confirm the lamp lights up. Replace the lamp unit. OK If the lamp goes out approximately 10 minutes after it lights up, the cumulative usage time of it exceeds 4 000 hours. Replace the lamp unit. Lamp does not turn ON.
No picture or abnormal picture is output NG Check each cable connection Connect properly OK Input a signal other than black and confirm No display of VIDEO input Follow the section "VIDEO input checks". No display of S-VIDEO input Follow the section "S-VIDEO input checks". No display of COMPUTER input Follow the section "COMPUTER input checks". No display of COMPONENT input Follow the section "COMPONENT input checks". No display of HDMI input Follow the section "HDMI input checks".
VIDEO Input checks Check the picture out of the S-VIDEO input. NG OK A Check the output waveform of L1002 (CVBS). NG A Check L1002 and around them. A Check IC1004 and around them. A Check R2014 and around them. OK A Check the output waveform of IC1004 (LPF) 6pin. NG OK A Check the output waveform of R2014 (CVBS). NG OK A Check the output wave form of IC1046. AW_LOUT1CKN : R1471 AW_LOUT2CKN : R1477 NG Follow the section "Main microprocessor checks". OK A Replace the A-P.C.Board.
COMPUTER Input checks A Check the output waveform of FL1003. R/Pr, G/Y, B/Pb NG A Check FL1003 and around them. A Check R1139-R1141, C1032-C1034 and around them. A Check R1008-IC1000(HD), R1009-IC1002(VD) and around them. A Check IC1001 and around them. OK A Check the input waveform of IC1001(ADV). C1032(G/Y), C1033(R/Pr), C1034(B/Pb) NG OK A Check the input signal of IC1001(ADV). R1149(HD sync), R1150(VD sync) NG OK A Check the output waveform of IC1001(ADV).
HDMI Input checks A Check the input signal of HDMI terminals. HDMI 1 (JK1007) : R1076-R1083 HDMI 2 (JK1006) : R1068-R1075 HDMI 3 (JK1005) : R1060-R1067 NG A Check HDMI terminals, IC1001 and around them. A Check IC1001 and around them. OK A Check the output waveform of IC1001(ADV). R1168(HD,VD,ACT), R1169(CLK), R1164(G9) NG OK A Check the output wave form of IC1046. AW_LOUT1CKN : R1471 AW_LOUT2CKN : R1477 NG Follow the section "Main microprocessor checks". OK A Replace the A-P.C.Board.
Remote control does not work Check the remote control (battery) NG Replace remote control (battery). OK A When remote control is operated, the signal can be detected at IC1014 pin 32. OK A Replace the A-P.C.Board. A Replace the R1232. NG A When remote control is operated, the signal can be detected at connector A9 pin 2. OK NG V Replace the V-P.C.Board.
SECTION 2 Model No. PT-AE8000U PT-AT6000E PT-AE8000EA / AE8000EH / AE8000EZ CONTENTS 1. Parts Location ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIS-2 1. 1. Electrical Parts Location (P.C.Board) 1. 2. Electrical Parts Location (Fan) 2. Disassembly Instructions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2. 1. Flowchart for Disassembly 2. 2. Removal of Top Cover 2. 3. Removal of A-P.C.Board 2. 4. Removal of Optical Block / Analysis Block 2. 5.
1. Parts Location 1. 1. Electrical Parts Location (P.C.Board） H B P A K1 V K2 M2 M1 S M3 L Board Name Board Name Function summary Function summary A Image processing system / Microcomputer M2 Temp sensor (Exhaust) S Control Panel M3 Temp sensor (Air flow) V Indicator LED B Ballast power / Ballast control L 3D-IR transmitter P Power supply (DC-DC) H Iris posistion sensor K1 AC Inlet Temp sensor (Intake) K2 Line Filter M1 1. 2.
2. Disassembly Instructions 2. 1. Flowchart for Disassembly * Before Disassembly the projector, turn off the POWER switch and disconnect the power plug from the wall outlet. * To assemble, reverse the disassembly procedures. * When tore off sticky tapes, please use a new thing without reusing it on the occasion of assembling. * Description of the illustration may be different from the real. Completed Product 2. 2. Removal of Top Cover 2. 3. Removal of A-P.C.Board 2. 4.
2. 2. Removal of Top Cover 1. Remove the Top panel. Top panel 1) Hold the top cover as shown in the diagram. 2) While pushing the arm in the direction of the arrow (inside projector), pull out from the groove. * Attaching the top panel 1) Hold the top cover as shown in the diagram. 2) Align the hinge with the support. 3) while pushing the arm in the direction of the arrow (inside projector) push it into the groove. 2. Unscrew the 9 screws on the top side and 1 screw on the rear side.
2. 4. Removal of Optical Block / Analysis Block 1. Remove the A-P.C.Board block according to the steps 1 through 2 in the section 2.3. "Removal of A-P.C.Board". 2. Loosen the 2 screws and remove the Lamp unit. 3. Unscrew the 1 screw and remove the V-P.C.Board. 4. Unscrew the 3 screws and remove the Front cover. XTBT969FJK Front cover V-P.C.Board XYN3+F6FJ 5. Unscrew the 1 screw and remove the A-P.C.Board earth metal. A-P.C.Board earth metal XYN3+F6FJ 6.
2. 5. Removal of L-P.C.Board 1. Remove the Optical block according to the steps 1 through 6 in the section 2.4. "Removal of Optical Block / Analysis Block". 2. Unscrew the 2 screws and remove the LED cover. LED cover Optical block XTBT969FJK 3. While pushing the LED cover in the direction of the arrow, and remove a LED fix tool. 4. Unscrew the 1 screw and remove the L-P.C.Board. LED cover LED fix tool LED fix tool XTBT969FJK L-P.C.
4. Unscrew the 1 screw and remove the M3-P.C.Board. M3-P.C.Board XTBT969FJK 2. 7. Removal of PBS Array / Iris Unit 1. Remove the Analysis block according to the section 2.4. "Removal of Optical Block / Analysis Block". 2. Unscrew the 5 screws and remove the Analysis case (upper). * Can be removal of PBS Array. XTV3+10GFJ * The incidence polarizer is installed in the Analysis case (upper). Be careful not to shift the installation position nor damage it. Analysis case (upper) XTBT969FJK 3.
2. 8. Removal of P-P.C.Board / B-P.C.Board 1. Remove the Top Cover according to the section 2.2 "Removal of Top Cover". 2. Loosen the 2 screws and remove the Lamp unit. 3. Unscrew the 3 screws and remove the Lamp house. XTBT969FJK Lamp house 4. Unscrew the 1 screw and remove the Lamp socket. Lamp socket XTW3+8PFJ 5. Unscrew the 5 screws and remove the Ballast block. * Remove the P2 connector. XYN3+F6FJ Ballast block 6. Unscrew the 2 screws and remove the P-P.C.Board. XYN3+F6FJ P-P.C.
7. Unscrew the 2 screws and while pressing to shut each hook of the 2 resinous stands, remove the B-P.C.Board. XTBT969FJK B-P.C.Board Note : 1) The direction the Power Fan install. 2) Roll the Fan cable one turn on core. B-P.C.B Resinous stands 2. 9. Removal of K1-P.C.board / K2-P.C.Board 1. Remove the A-P.C.Board earth metal according to the steps 1 through 5 in the section 2.4. "Removal of Optical Block / Analysis Block". 2. Unscrew the 4 screws and remove the Optical Block and Analysis Block.
5. Unscrew the 2 screws and remove the K-P.C.Board block. K1-P.C.Board K-P.C.Board block K2-P.C.Board XYN3+F6FJ XYN3+F6FJ 2.10. Remonal of M1-P.C.Board 1. Remove the Top Cover according to the section 2.2 "Removal of Top Cover". 2. Unscrew the 1 screw and remove the V-P.C.Board. XTBT969FJK 3. Unscrew the 3 screws and remove the Front cover. Front cover V-P.C.Board XYN3+F6FJ 4. While pressing to shut each hook of the Adjuster leg, remove the Adjuster leg (lens side). Adjuster leg 5.
SECTION 3 < Adjustments > Model No. PT-AE8000U PT-AT6000E PT-AE8000EA / AE8000EH / AE8000EZ CONTENTS 1. Adjustment items and procedure ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-2 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-7 1. 1. Flicker Adjustment 1. 2. Data Transfer 1. 3. Model Information Setup 1. 4. Model Information Setup 1. 5. Clog Sensor calibration 2. Microprocessor update procedure 2. 1.
1. Adjustment item and a procedure When the following components in this projector are replaced, adjustments are required. Adjust each item according to the table below. Adjustment Items Replaced parts Remarks 1. 1. Flicker Adjustment OPTICAL BLOCK / A-P.C.Board 1. 2. Data Transfer A-P.C.Board 1. 3. Model Information Setup A-P.C.Board 1. 4. Serial Number Setup A-P.C.Board 1. 5. Clog Sensor Calibration A-P.C.Board / M3-P.C.board Save data to a PC before A-P.C.
5. 1) Click the [ Reception ] button of Micom Data. 2) Select the save place and click the [ Save ] button. 3) When the progress bar reaches the right-side end, the save of data is completion. 4) Save the each data in the same procedure as 1-3. ① ③ ② 1. 2. 4. Restore the Backup EEPROM Data (After A-P.C.Board exchange) 1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red). 2. Start up service software ［Service ORCA11.exe］ with a computer. 3.
1. 3. Model Information Setup 1. 3. 1. Required equipments 1. PC : Use it as adjustment use. 2. Communication cable : D-sub 9pin (male/emale RS-232C straight) 3. Software : ［Service ORCA11.exe］Adjustment software is downloaded from the projector service homepage. 1. 3. 2. Preparation 1. Connect the RS-232C termanal of projector and PC with a RS-232C cable. Projector Computer RS-232C cable (Streight) 1. 3. 3. Setting method 1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red).
1. 4. Serial Number Setup 1. 4. 1. Required equipments 1. PC : Use it as adjustment use. 2. Communication cable : D-sub 9pin (male/emale RS-232C straight) 3. Software : ［Service ORCA11.exe］Adjustment software is downloaded from the projector service homepage. 1. 4. 2. Preparation 1. Connect the RS-232C termanal of projector and PC with a RS-232C cable. Projector Computer RS-232C cable (Streight) 1. 4. 3. Setting method 1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red). 2.
1. 5. Clog Sensor Calibration * This operation should be done with the main body is completely assembled and set on the floor and the adjuster legs are set in the main body. (A state of Disassembly, cannot correct it.) * Install the projector so that cold air or hot air from air conditioners does not come in to direct contact with the air intake port or air exhaust port. * Please carry it out after “Data Transfer” of Micom Data. 1. 5. 1. Required equipments 1. PC : Use it as adjustment use. 2.
2. Microprocessor update procedure * The update is done by SERIAL terminal connection. * During update, prevent PC from going into stand-by or shut down. 2. 1. Update by the SERIAL terminal connection 2. 1. 1. Equipment to be used 1. Computer : Use it for the transfer of update data. 2. Communication cable : D-sub 9pin (male/female RS-232C straight) 3. Firmware update tool : [PgSendORCA11.exe] Update tool is downloaded from the projector service homepage. 4.
6. Click the [ SOFT UPDATE ] button. 7. Click the [OK] button and start update. * When updated the software of FRC(Frame Creation), a version is not displayed. 8. Click the [ OK ] button after completion message is displayed. * Reboot Projector, and please confirm whether the version of the Microprocessor Software is updated definitely, with sub menu " STATUS " of the main menu " EXT OPTION " .
SECTION 4 < Schematic Diagram > Model No. PT-AE8000U PT-AT6000E PT-AE8000EA / AE8000EH / AE8000EZ Important Safety Notice Components identified by the intemational symbol have special characteristics important for safety. When replacing any of these components, use only the manufacturer's specified ones. ■Notes 1. Resistor All the resistors are carbon 1/4W resistors, unless marked as follows. The unit of resistance is an OHM [Ω] (K=1 000 M=1 000000).
1. Block Diagram 1.1. Power Supply SWITCHING TRANSFORMER STB 3.3 V PHOTOISOLATOR HOT F9101 SWITCHING REGULATOR THERMOSENSOR MAIN POWER D9102 P1 K4 AC RELAY LINE FILTERS D9101 RECTIFIER COLD SWITCHING TRANSFORMER POWER FACTOR CORRECTION SW9101 K2-P.C.Board SWITCHING REGULATOR K3 P2 K1 1 K1-P.C.Board Q107 15 V 4 VOLT_DET 15 17 V 11 +6 V 5 FAN 14 V 9 3.3 V 1 3.3 V 2 3.3 V 3 MAIN/STB A-P.C.Board A5 14 PHOTOISOLATOR 15 V AVR PHOTOISOLATOR P-P.C.
1. BLOCK DIAGRAM 1. 2. Signal Processing IC1001 IC1049 IC1046 R,G,B IC1030 IC1052 X1003 24MHz X1002 34.455MHz COMPUTER IN IC1000 HD JK1008 X1004 27MHz A1 IC1027 VD RESET E R IC1002 INHIBIT_RGB LCD (R) Y,PB/CB,PR/CR JK1003 HDMI1 HDMI-1 IN FPGA PIVS PICLK 3-ch ADC, HDMI RxD 35.
B2 2 3 A 4 A4 A14 A21 CINEMA FILTER DRIVE ZOOM MOTOR 5 DIA-4 FOCUS MOTOR 6 A15 ! POWER FAN A16 ! EXHAUST FAN 7 A17 A18 ! INTAKE FAN 8 ! LAMP FAN A19 5 PWM CONT DGND LCD17V A12 M1 ! IRIS FAN 9 STB3.3V INTAKE AIR TEMP M2 CF2401 M1-P.C.B ! EXHAUST AIR TEMP FILTER AIR TEMP M2-P.C.B M3-P.C.
2 5 6 DIA-5 9 10 11 12 14 15 16 17 Motor driver 13 VM2 14 VM3 16 15 PWMB 17 BIN1 BIN2 18 19 GND 20 Vcc STBY AO2 AO2 BO2 BO2 PGND2 5 6 7 8 9 AA_LAMPSW AA_PWMOUT AA_BLST_CT AA_LAMP_SENSE POW_FAILURE AA_SCL2 AB_IR_ON5 AB_IR_ON6 C2035 470p 50V C2036 470p 50V J0JYC0000024 OUT2 L1073 L1075 2 3 SHIFT- SHIFT+ 1 A14 C2049 50V C1217 470p 50V GND J0JYC0000024 R1308 47k 10 470p C1216 0.
AA_GEN_RXD AA_MOFF_IRQ Sub_M om AA_ARM_IRQ AA_ARM_MODE AA_ARM_INIT AA_BOOT_MODE AA_ARM_RESET AB_IR_ON5 AB_IR_ON6 AA_SDA2 AA_INHIBT_RGB AA_HDMI1_HPGDET AA_HDMI1_HOTPLUG AA_HDMI2_HPGDET F6 IC1046 F5 PI2D[24] AB_IR_ON3 F4 PI2D[25] AB_IR_ON4 F3 PI2D[26] F2 PI2D[27] IC1046 F1 PI2D[28] IC1046 G6 PI2D[29] IC1046 G3 PI2HSB IC1046 G5 PI2VSB AA_HDMI3_HOTPLUG IC1046 G2 PI2ACTB AA_SCL1 IC1046 G4 PI2FLD AA_SDA1 IC1046 A7 PI2CLK AA_ADV1_IRQ1 P3 ANSYIN ANSCIN AA_RXD_MAIN AA_ANM
AY_LOUT3CP AY_LOUT3DP AY_LOUT3EN AY_LOUT3EP AY_LOUT4CKP AY_LOUT4AN AY_LOUT4AP AY_LOUT4BN AY_LOUT4BP AY_LOUT4CP AY_LOUT4DN AY_LOUT4DP AY_LOUT4EN AY_LOUT4EP AY_LOUT3CN R1724 AY_LOUT3CP 1% 100 AY_LOUT3DN R1725 AY_LOUT3DP 1% 100 AY_LOUT3EN R1726 AY_LOUT3EP 1% 100 R1705 0 R1706 0 AY_LOUT4CKN R1727 AY_LOUT4CKP 1% 100 AY_LOUT4AN R1728 AY_LOUT4AP 1% 100 AY_LOUT4BN R1729 AY_LOUT4BP 1% 100 AY_LOUT4CN R1730 AY_LOUT4CP 1% 100 AY_LOUT4DN R1731 AY_LOUT4DP 1% 100 AY_LOUT4EN R1732 A
3. SCHEMATIC DIAGRAM 3. 2. S-P.C.Board / L-P.C.Board / V-P.C.Board < S-P.C.Board > 2.48V *SW2004 SW2013 1000p 50V 50V B3EA00000200 B3EA00000200 B3EA00000200 D3016 B3EA00000200 B3EA00000200 D3005 D3006 D3012 D3013 D3014 B3EA00000200 B3EA00000200 B3EA00000200 B3EA00000200 D3007 B3EA00000200 D3008 B3EA00000200 D3009 B3EA00000200 D3002 B3EA00000200 ZA3001 EVQPLHA15 K4CD01000013 SW2009 2.48V BACK FOCUS- D3003 SW2008 LEFT EVQPLHA15 2.48V B3EA00000200 EVQPLHA15 1.
TOP 1 + A A25 C2045 R1574 R1910 C1864 ZA1007 L1119 C1496 D R1911 R2054 C2058 F G H J K L M N P R T U C2051 ZA1006 C1476 C2047 C1475 ZA1002 CL1038 CL1034 CL1035 CL1036 L1028 CL1037 CL1032 CL1033 CL1030 CL1031 R1279 R1283 L1027 CL1028 R1231 CL1029 R1232 C1167 L1052 R1281 R1284 L1111 C2049 R1601 R1599 CL1290 R1586 R1587 R1600 R1590 C1481 1 Y AA AB 3 2 2 3 5 6 9 10 11 12 13 14 18 19 20 21 22 3 R1275 R1268 R1269 R1267 CL1082 CL1079 L1074 CL1080 CL1
R1871 C1675 C1664 C1663 C1674 C1672 C1670 C1666 R1856 R1855 C1673 C1671 C1665 C1669 R1857 R1858 C1797 C1793 C1802 C1798 C1794 C1803 C1799 C1804 C1742 C1738 C1739 C1730 C1765 C1740 C1726 C1766 C1741 C1727 C1757 C1796 C1708 C1728 C1724 C1731 C1756 C1732 C1697 C1761 C1760 11 R1796 C1788 C1789 C1790 C1785 C1787 C1786 R1798 R1797 R1976 R1977 R1946 R1854 C1662 C1650 C1651 C1777 C1783 C1805 C1776 C1737 14 1 C1657 C1655 C1659 C1806 C1811 R1955 R1839 C1660 R1838 C1654 C1656 C
4. CIRCUIT BOARDS DIAGRAM 4. 2. S-P.C.Board / V-P.C.Board / L-P.C.Board E V-P.C.Board L-P.C.Board A K A K K A A K A K A K A K A K A K A K A K A K C2101 A 1 RM2101 K S-P.C.
SECTION 5 < Exploded Views & Parts List > Model No. PT-AE8000U PT-AT6000E PT-AE8000EA / AE8000EH / AE8000EZ CONTENTS 1. Exploded Views ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ SPL-2 1. 1. Parts Location 1. 2. Packing Parts 2.
1. Exploded Views 1.1. Part Location (1/3) 41 42 19 211 203 211 211 203 212 39 204 214 204 214 204 5 22 201 211 65 13 204 9 201 37 M3-P.C.Board 14 203 204 206 204 9 2 11 201 12 46-1 V-P.C.Board 211 49-1 1 204 46 16 211 49 201 9 204 204 63 64 211 K2-P.C.Board 204 7 204 204 23 9 18 6 K1-P.C.
1. Exploded Views 1.1. Part Location (2/3) 211 211 213 29 26 23 24 211 204 211 211 211 213 23 204 211 211 25 26 28 24 35 27 33 34 34 31 211 32 211 32 204 215 23 B-P.C.Board 206 30 204 204 24 210 215 204 211 P-P.C.Board A-P.C.Board 211 211 211 15 211 211 204 204 211 20 M1-P.C.Board 204 36 204 204 S-P.C.
1. Exploded Views 1.1. Part Location (3/3) 51 53 54 52 55 202 54-1 54-2 55-1 204 47 58 205 204 205 205 205 205 205 207 205 58-10 48 204 207 204 H-P.C.Board 58-7 204 208 58-2 205 207 58-1 204 205 204 205 204 58-5 58-6 204 205 204 38 205 58-4 205 58-8 204 209 M2 P.C.Board 209 209 58-9 204 57 205 57-8 205 57-3 57-6 57-1 57-4 57-7 50 58-11 204 204 204 57-5 204 57-2 204 58-3 204 L-P.C.
1.2.
2. Replacement Parts List Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. 46 MECHANICAL PARTS 46-1 47 1 Part No. TTFA0288 TBLG3090 TQFX301 Part Name & Description Remarks Pcs 1 RUBBER LEG (REAR) 1 LAMP EXCHANGE LABEL 1 TOP COVER 1 FRONT COVER ASSY 1 REMOTE CONTROL RECEIVER 1 LENS CAP ASSY 1 LENS CAP STRAP 1 PANASONIC BADGE 1 3D LOGO BADGE 1 MODEL NO. LABEL 1 MODEL NO.
Ref.No. Part No. Part Name & Description Remarks Pcs TXJ/M3RWDZ M3-A13 CABLE TXJ/L2THHZ LAMP CABLE TXJ/B2RWDZ B2-A4 CABLE TXJ/P2RWDZ-1 B1-P2 CABLE TXJ/P3RWDZ-1 P3-A5 CABLE TXJ/V1RWDZ V1-A9 CABLE TXJ/S1RWDZ S1-A8 CABLE TXJ/M2RWDZ M2-A11 CABLE TXFEW01RWDZ M1-A12 CABLE TXFEW02RWDZ L1-A24 CABLE TXJ/H1RWDZ H1-A10 CABLE 1 1 1 1 1 1 1 1 1 1 1 M3 - A13 Ref.No. Part No.
Ref.No.
Ref.No.
Ref.No. Part No.
Ref.No.
Ref.No.
Ref.No.
Ref.No. R1937 R1938 R1939 R1940 R1941 R1942 R1943 R1944 R1945 R1946,47 R1948 R1949 R1950 R1951 R1952 R1953 R1954 R1955 R1956,57 R1958 R1959 R1960 R1961 R1962 R1963 R1964 R1965 R1966 R1967 R1968 R1969 R1970 R1971 R1972,73 R1974 R1975 R1976,77 R1978-80 R1986 R1988,89 R1990 R1991,92 R1993,94 R1995 R1996-98 R1999-01 R2004 R2008-10 R2011 R2012-14 R2016,17 R2020 R2021 R2022-24 R2025 R2026,27 R2032,33 R2034-37 R2040,41 R2044 R2045,46 R2054 R2055 R2056 R2058 Part No.
Ref.No. Part No. Part Name & Description Pcs D3012-14 B3EA00000200 TSHG6210-ASZ B3EA00000200 TSHG6210-ASZ D3016 3 1 L1 K1KA09A00220 PLUG,9P 1 ZA3001 K4CD01000013 TERMINAL 1 6550059239 1 K1 CIRCUIT BOARD K1 Remarks Ref.No. MISCELLANEOUS TXAWC01VKJ8 AC INLET U TXJ/K1VKG7 K1-KP CABLE 1 1 K2 6550059246 CIRCUIT BOARD K2 1 F9101 K5E802BZA004 FUSE 250V 8A 1 SW9101 K0AAKA000014 SWITCH 1 SPL-15 Part No.
