S P E C F I L E P ro d u c t N u m b e r : PT-AE7000 P ro d u c t N a m e : Full High-Definition Home Cinema Projector As of September 2011. Specifications and appearance are subject to change without notice.
S P E C F I L E Full High-Definition Home Cinema Projector PT-AE7000 Specifications Main unit Power supply Power consumption LCD* 1 panel Lamp* 2 Lens Projection size Panel size Display method Drive method Pixels 2D projection 3D projection Throw distance Colors Brightness* 3 Center-to-corner uniformity ratio* 3 Contrast ratio* 3 Resolution Scanning frequency RGB YPBPR (YCBCR) Video/S-Video Optical axis shift* 6 Keystone correction range Installation On-screen menu languages Terminals HDMI
S P E C F I L E Full High-Definition Home Cinema Projector Remote control unit Power supply Operation range* 1 2 Dimensions (W × H × D) Weight PT-AE7000 3 V DC (AA/R6 type battery × 2) Approx. 7 m (23 ft) when operated from directly in front of the signal receptor 48 × 138 × 28 mm (1-7/8˝ × 5-7/16˝ × 1-3/32˝ ) Approx. 125 g (4.
S P E F C I L E PT-AE7000 Full High-Definition Home Cinema Projector 364 (14-11/32) 345 (13-19/32) Dimensions 14 151 (9/16) 95 (3-3/4) (5-15/16) 137 (5-13/32) (2-15/16) 74 19 (3/4) unit : mm (inch) NOTE: This illustration is not drawn to scale.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Standard setting-up position 154 (6-1/16) unit : mm (inch) Upper edge of projected image H L 204 (8-1/32) H Projected image L Lower edge of projected image 52.5 (2-1/16) L Projected image 70 (2-3/4) W 65 (2-9/16) NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKA110S. This illustration is not drawn to scale.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Projection distance for 2.35:1 aspect ratio screen Projection size (16:9) Diagonal length Projection distance (L) Min (Wide) 1.0 2 m / 4 0 ˝ 1. 2 7 m / 5 0 ˝ 1.52 m / 6 0 ˝ 1. 2 3 m / 1.5 5 m / 1.87 m / 1.78 2.0 3 2. 2 9 2.5 4 3.0 5 3.81 2.19 2.51 2.8 3 3.15 3.78 4.74 m m m m m m / / / / / / 70 ˝ 80˝ 90˝ 10 0 ˝ 12 0 ˝ 15 0 ˝ 5.0 8 m / 2 0 0 ˝ 6.3 5 m / 2 5 0 ˝ 7.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. H (Width of projected image) 0.26H V (Height of projected image) 1.0V 0.26H 1.0V Standard position of projected image Installable angle Install the projector at an angle within the range shown below. -10° +10° • Horizontal direction The projector may be installed at a horizontal angle of ±10°.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 74 kHz, vertical scanning frequencies of 24 Hz to 85 Hz, and a dot clock of 154 MHz maximum can be input. Compatible signal Display mode NTSC/NTSC4.43/PAL-M/PAL60 - 720 × 480i 15.7 59.9 - PAL/PAL-N/SECAM - 720 × 576i 15.6 50.0 - 525i (480i) 480i 720 × 480i 15.7 59.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Supported 3D video signal list When [3D INPUT FORMAT] is set to [AUTO], the 3D signals supported by this projector are the HDMI signals in the table below.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names No. 1 2 3 4 5 Signal name – TXD RXD – GND Description NC Transmitted data Received data NC Ground No.
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Control commands Command PON * 1 POF * 1 IIS OMN OEN OBK OCU OCD OCL OCR OLE OST O3D OFZ FC1 OSH * 2 OVM OWM VS1 VPM OOT OMM DPA DCM OVL OSM Function Standby power on Standby power off Input signal selection Menu Enter Return Cursor up Cursor down Cursor left Cursor right The same function as “LENS” button Default The same function as “3D” button Freeze The same function as “FUNCTION” button Blank on/off Picture mode switch Wavef
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Status request commands Command Description Parameter QPW QIN Standby power status Input signal status QPM Picture mode status QSH QFZ QOT Blank function status Freeze function status Off timer status QWM Waveform monitor statusutton 000 CP1 HD1 RG1 NOR DCN GM1 0 = 0 = 0 = 4 = 7 = 0 = 3 = 5 = 7 = Option Menu Command QVX: AGOS0=p1p 2 Gamma output level (Y) Gamma output level (R) AGOS1=p1p2 Gamma output level (G) AGO
S P E C F I L E PT-AE7000 Full High-Definition Home Cinema Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 100 mm (3-15/16˝ ) or more around the projector’s air intake openings. 3.
