Installation Guide

ManualsBrandsPanasonic ManualsDuct DampersPC-RD05C5

1. Position the ceiling radiation damper on the inlet side of the fan such that the holes in the

damper mounting flanges line up with the holes in the flange of the fan housing. Secure the

damper to the fan housing using the four #10-32 machine screws/nuts supplied.

2A. For a damper used with a fan requiring a plug connector to pass through the damper, secure

the plug connector using the wiring bracket and #8 course threaded screw supplied. (See Figure

2A) If the plug connector cannot reach through the damper to the

grill plug attachments, release the clips holding the wiring inside the

fan with a Phillips-Head screwdriver. make sure the wire lead or

plug connector does not interfere with the closing of the damper.

2B. For a damper used with a fan that does not require a plug

connector, secure the wiring bracket supplied to the damper frame

using the supplied #8 course threaded screw supplied. Make sure the wiring bracket covers the

notch in the frame. (See Figure 2B).

3. With the damper secured to the fan housing, the assembly can be attached to the structure

above using the holes in the fan housing flange or the supplied mounting brackets. If the

mounting brackets are used, position the mounting brackets under the damper mounting flanges

or under the fan housing flange as required. Position the slot so it aligns with the holes in the fan housing and/or the holes in

the damper mounting flanges (See Figure 3). If the damper/fan is being attached to the adjacent structure, the brackets must

be used and adjusted to fit accordingly. If the damper/fan is supported from structure above, the brackets should be adjusted

so the ends of the brackets align accordingly. Once the brackets are adjusted, attach them to the

flange of the fan housing using four #10-32 screws and nuts supplied. A minimum of two

fasteners per side is required.

4. The ceiling penetration should be located within ceiling tiles or panels without necessitating

cuts in the ceiling suspension main runners or cross tees. If required, a maximum of one runner

or cross tee may be cut to enable proper damper location and installation. Each cut end shall be

supported by a min. 12 swg (2.7) vertical hanger wire. The opening in the ceiling should be the

same size as the outside of the damper frame.

5. Position the damper/fan assembly such that the bottom edge of the damper is flush with the

finished surface of the ceiling. Attach the damper/fan assembly to the structure above or adjacent

to it. If the damper/fan is being attached to the assembly above, a minimum of 12 swg. (2.7)

hanger wire must be used. A minimum of two hanger wires on two opposite sides are required. The hanger wires can be

attached directly to the fan housing flange or to the ends of the mounting brackets. If the damper/fan assembly is being

directly mounted to the adjacent structure, a minimum #8 (M4) sheet metal screws or 1/2" dia. bolts/nuts must be used. If

necessary, a min. 1/2" wide flange is to be attached to the damper using a minimum #8 (M4) sheet metal screw, 3/16" pop

rivets, welds or bolts at 6" (152) o.c. maximum. A minimum of 2 connections per side is required.

6. For other installation details see Panasonic Installation Instructions.

For horizontal mount only.

Certified to UL555C.

Up to 3 hour non-combustible assemblies

ceiling radiation damper

PC-RD05C5 installation instructions

Non-Combustible Ceiling Radiation Dampers PC-RD05C5 (1/9) September 2017 M-54447-E

Information is correct at time of printing. However, we reserve the right to make changes without notice. Note: All dimensions are shown in () millimeters..

Panasonic

For fan model:

WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15VK1, FV-11-15VKL1.

WhisperCeiling: FV-05VQ5, FV-08VQ5, FV-08VQL5, FV-08VQL6, FV-11VQ5, FV-11VQL5, FV-11VQL6, FV-15VQ5, FV-15VQL5,

FV-15VQL6, FV-0511VQ1, FV-0511VQC1, FV-0511VQCL1, FV-0511VQL1, FV-1115VQ1, FV-1115VQL1.

WhisperSense: FV-08VQC5, FV-08VQCL5, FV-08VQCL6, FV-11VQC5, FV-11VQCL5, FV-11VQCL6.

WhisperFit: FV-05VF2, FV-05VFL4, FV-05VFM2, FV-08-11VF5, FV-08-11VFL5, FV-08-11VFM5, FV-08VF2, FV-08VFL4, FV-08VFM2,

FV-11VF2, FV-11VFL4.

WhisperValue: FV-05VS1, FV-05VS3, FV-08VS3, FV-08VSL3, FV-10VS1, FV-10VS3, FV-10VS3E, FV-10VSL3, FV-10VSL3E, FV-0510VS1,

FV-0510VSA1 + FV-0510VSB1, FV-0810VSS1, FV-0810VSSL1, FV-0510VSC1, FV-0510VSL1 and FV-0510VSCL1.

Plug

Connector

Wiring

Bracket

Fan Housing

Flange

Mounting

Brackets

Hanger Wire

Fan Housing

Damper

Mounting Bracket

Ceiling Tile

Figure 1A Figure 1B

Figure 2A

Figure 2B

Figure 3

SEE DETAILS ON UL

CLASSIFICATION

MARKING ON

ENCLOSED PRODUCT

CLASSIFIED

Summary of content (9 pages)

PAGE 1
Panasonic Up to 3 hour non-combustible assemblies ceiling radiation damper PC-RD05C5 installation instructions ® Hanger Wire Fan Housing Mounting Bracket Damper Ceiling Tile Figure 1A Figure 1B For fan model: WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15VK1, FV-11-15VKL1. WhisperCeiling: FV-05VQ5, FV-08VQ5, FV-08VQL5, FV-08VQL6, FV-11VQ5, FV-11VQL5, FV-11VQL6, FV-15VQ5, FV-15VQL5, FV-15VQL6, FV-0511VQ1, FV-0511VQC1, FV-0511VQCL1, FV-0511VQL1, FV-1115VQ1, FV-1115VQL1.
PAGE 2
Panasonic Up to 1 hour combustible assemblies ceiling radiation damper PC-RD05C5 installation instructions ® Fan Housing Finish Flooring Vapor Barrier Sub-Flooring Wood Truss Mounting Bracket Resilient Channel (Check UL design directory) Drywall Support Assembly Figure 1 Gypsum (Thickness may vary) For fan model: WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15VK1, FV-11-15VKL1.
PAGE 3
Panasonic Up to 1 hour combustible assemblies ceiling radiation damper PC-RD05C5 installation instructions ® 4. With the damper secured to the fan housing, attach the supplied mounting brackets. Position the mounting brackets under the damper mounting flanges or under the fan housing flange as required. Position the slot so it aligns with the holes in the fan housing and/or the holes in the damper mounting flanges (See Figure 3). The brackets can be adjusted to fit between the damper supports.
PAGE 4
Panasonic ® Ensamblaje de hasta 3 horas Compuerta de radiación para techo no combustible Instrucciones de instalación PC-RD05C5 Alambre de Suspensión Caja del Ventilador Soporte Compuerta Placa del techo Figura 1A Figura 1B Para modelos de aspa: WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15VK1, FV-11-15VKL1.
PAGE 5
Panasonic ® Caja aspa Acabado Ensamblaje de hasta 1 hora Compuerta de radiación para techo combustible Instrucciones de Instalación PC-RD05C5 Barrera Vapor Sub-Techo Viga Madera Soporte Canal Resistente (Revisar diseño UL) Soporte de Compuerta 2 x 4 Yeso (Grueso varia) Ensamblaje Cartón Yeso Soporte Compuerta de radiación para techo combustible PC-RD05C5 (5/9) Septiembre 2017 M-54447-E Figura 1 Para modelos de aspa: WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15
PAGE 6
Panasonic ® Ensamblaje de hasta 1 hora Compuerta de radiación para techo combustible Instrucciones de Instalación PC-RD05C5 4. Una vez que la compuerta se encuentra asegurada a la caja del aspa, sujeta los soportes de montura suministrados. Ubica los soportes debajo de las ranuras de montura de la compuerta o debajo de la ranura de la caja del aspa. Ubique la ranura para que sea alineada a los huecos en la caja del aspa y/o los huecos en los bordes de montaje de la compuerta (Ver Figura 3).
PAGE 7
Panasonic ® Registre au plafond d'atténuation de radiations jusqu'à 3 heures en matériaux non-combustibles Instructions d'installation PC-RD05C5 Câble de suspension Boîtier du ventilateur Support de fixation Registre Dalle de plafond Figure 1A Figure 1B Pour modèles de ventilateur : WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15VK1, FV-11-15VKL1.
PAGE 8
Panasonic Volet au plafond d'atténuation de radiations jusqu'à 1 heure en matériaux combustibles Instructions d'installation PC-RD05C5 ® Boîtier du Revêtement Pare-vapeur Sous-Plancher Ferme en bois Support de montage Barre résiliente (Consultez le manuel UL) Support du volet Figure 1 Pour modèles de ventilateur : WhisperGreen: FV-05-11VK1, FV-05-11VKL1, FV-05-11VKS1, FV-05-11VKSL1, FV-11-15VK1, FV-11-15VKL1.
PAGE 9
Panasonic ® Volet au plafond d'atténuation de radiations jusqu'à 1 heure en matériaux combustibles Instructions d'installation PC-RD05C5 4. Avec le registre fixé au boîtier du ventilateur, fixez les supports de fixation fournis. Positionnez les supports de fixation sous les brides de fixation du registre ou sous le boîtier du ventilateur, comme nécessaire.