NV-MV41GN.book 1 ページ ２００４年３月１日 月曜日 午後７時１２分 Operating Instructions Video Cassette Recorder Model No.
NV-MV41GN.book 2 ページ ２００４年３月１日 月曜日 午後７時１２分 Cautions before you operate this VCR Avoid: • Humidity and dust. • Extreme heat such as direct sunlight. • Magnets or electromagnetic objects. • Touching internal parts of the VCR. • Water or some other liquid. • Lightning. (Disconnect the aerial plug from the VCR during lightning storms.) • Anything heavy on the VCR. • Connecting or handling the equipment with wet hands.
NV-MV41GN.
NV-MV41GN.book 4 ページ ２００４年３月１日 月曜日 午後７時１２分 Setting the Remote Control to Operate Your TV Connections You can operate the TVs of the manufacturers listed below with the remote control after setting it. This section shows you how to connect the VCR to an aerial, TV, etc. This setting procedure allows you to operate the TVs of some manufacturers using the supplied remote control. Basic Connections The following connections are required to record and play back the video cassette through the TV.
NV-MV41GN.book 5 ページ ２００４年３月１日 月曜日 午後７時１２分 Tuning the TV to Your VCR Storing TV Broadcasts in Your VCR The VCR supplies a signal to the TV via the RF coaxial cable on channel NZ21-69 or AU28-69. If you have connected the VCR to the TV through the Audio/ Video input sockets, then you do not need to follow the procedure below. To view the pictures from the VCR, set to the AV mode on the TV with [AV] (2).
NV-MV41GN.book 6 ページ ２００４年３月１日 月曜日 午後７時１２分 Auto Tuning Using the On Screen Display For Australia Manual Tuning Procedure If the VCR is not correctly tuned by Auto Tuning, follow the procedure below. Introduction Auto Tuning using the On Screen Display should be performed according to the following method if necessary. 1 Press [MENU] (9) to display the Main menu on the TV screen. Preparations • Confirm that the TV is on and the VCR viewing channel is selected.
NV-MV41GN.book 7 ページ ２００４年３月１日 月曜日 午後７時１２分 Setting the Clock of Your VCR Settings Using the On Screen Display In the event of a power failure, the clock will operate on its back up system for a minimum of 3 years. After 3 years, clock back up in the event of a power failure can only be guaranteed for maximum of 1 hour. Preparations • Confirm that the TV is on and the VCR viewing channel is selected. • Turn on the VCR. Preparations • Confirm that the TV is on and the VCR viewing channel is selected.
NV-MV41GN.book 8 ページ ２００４年３月１日 月曜日 午後７時１２分 4 Tape Mode/Rec Mode indicator (SP/LP/EP) Option Setting 5 Cassette-in indicator 6 Colour system indicator Any selected colour TV system except [AUTO] appears on screen display. See the “To Set the Colour TV System” (page 7). MENU CLOCK SET TUNER PRESET SYSTEM OPTION TAPE REFRESH NAVI MEMORY 0PROG. SELECT : , ENTER END : MENU 7 NAVI CHECK indicator During playback, press the [STATUS/ NAVI CHECK] (32) repeatedly until the NAVI CHECK indicator appears.
NV-MV41GN.book 9 ページ ２００４年３月１日 月曜日 午後７時１２分 OSD REC: To set the conditions for the OSD Recording function. • Press [2 1] (28) to select [ON] or [OFF]. OFF: ON: Playback Preparations • Confirm that the VCR is on. • Confirm that the TV is on and the VCR viewing channel is selected. • Insert a recorded video cassette. Initially set at this position. This setting enables OSD Recording. (See page 11.) If you select [ON], [JET NAVIGATOR] is set to [OFF] automatically. For Normal Playback: Press [PLAY] (8).
NV-MV41GN.book 10 ページ ２００４年３月１日 月曜日 午後７時１２分 To Play Back a Recorded Part Repeatedly Recording Press [REPEAT] (30). The [R] indication appears on the VCR display. • A recorded part on the tape must be at least 15 minutes long. • When recording over the same location on a tape, it may not function correctly. Preparations • Confirm that the VCR is on. • Confirm that the TV is on and the VCR viewing channel is selected. Operations 1 Insert a video cassette with an intact erasure prevention tab.
NV-MV41GN.book 11 ページ ２００４年３月１日 月曜日 午後７時１２分 To Display the Approximate Remaining Tape Time To Record the Present Date and Time (OSD Recording) on the same screen as the picture The remaining tape time can be displayed in the VCR display. 1 Select [TAPE SELECT] from the On Screen Display and select the corresponding video cassette tape length. See page 8. This function allows you to record the present date and time on the same screen as the picture being recorded. Operations 1 Set [OSD REC] to [ON].
NV-MV41GN.book 12 ページ ２００４年３月１日 月曜日 午後７時１２分 Recording from an external source To Delete all of a Cassette’s Contents (Tape Refresh Function) This function can be used to make up an edited tape from other recordings or video sources. A new scene can be added to the end of previous one. You can delete a cassette contents (the picture, the sound and the Jet Navigator data) all at once.
NV-MV41GN.book 13 ページ ２００４年３月１日 月曜日 午後７時１２分 9 Press [TIMER (REC)] (14) to switch the VCR over to the timer recording standby mode. • When [JET NAVIGATOR] is set to [ON] (see page 8), the [PROGRAMME IS COMPLETE. REMAINING PROGRAMME 49.]* message appears. • When [JET NAVIGATOR] is set to [OFF] (see page 8), the [PROGRAMME IS COMPLETE.]* message appears. * These messages will not appear if timer recording is started immediately after [TIMER (REC)] (14) is pressed.
NV-MV41GN.book 14 ページ ２００４年３月１日 月曜日 午後７時１２分 Setting other Programmes in Succession Timer recording for the same programme on the next week (Intelligent Timer) Repeat steps 1-9 of Easy Timer Programming (page 13). When you wish to set the timer recording for programmes which will be recorded within 1 week and you have ever recorded the programmes before, you can record them soon with I-TIMER function without entering day and time by buttons.
NV-MV41GN.book 15 ページ ２００４年３月１日 月曜日 午後７時１２分 To Delete the Jet Navigator Data of a Single Video Cassette Tape Search Functions Keep [CANCEL] (5) pressed for more than 5 seconds while the Jet Navigator list appears. [ss] appears on the list. See page 8 to delete all the Jet Navigator data stored in the VCR memory. Jet Navigator This VCR can display a list of the recorded programmes on the inserted video cassette on the TV screen.
NV-MV41GN.book 16 ページ ２００４年３月１日 月曜日 午後７時１２分 To Demonstrate the Jet Navigator Function Keep [NAVI] (25) pressed for more than 5 seconds without inserting a cassette tape. Notes: • Searching in either direction is possible up to the 20th index signal. • If you press either of [INDEX] (13) too many times, simply press the other [INDEX] (13) (indicating the opposite direction) to correct it. In this way, you can reduce the displayed figure down to 1.
NV-MV41GN.book 17 ページ ２００４年３月１日 月曜日 午後７時１２分 Recording will not operate correctly The symptom description is indicated in brackets [ Before Requesting Service Message of On Screen Display The error message is indicated in brackets [ ]. [PLEASE PUT IN A VIDEO CASSETTE.] • [REC/OTR] (38) ([REC] (15)) or [TIMER (REC)] (14) has been pressed without a video cassette inserted. #Insert a video cassette. [The picture is recorded with noise or a blank screen.] • The aerial or aerial cable is defective.
NV-MV41GN.book 18 ページ ２００４年３月１日 月曜日 午後７時１２分 Crystal View Control The crystal view control function ensures that you always obtain the optimum picture quality so that you get the best picture automatically. Adjusting the Playback Picture Under normal conditions, the VCR automatically adjusts the playback picture for optimum quality. However, in some cases it may be necessary to adjust it manually.
NV-MV41GN.
NV-MV41GN.book 20 ページ ２００４年３月１日 月曜日 午後７時１２分 Matsushita Electric Industrial Co., Ltd. Web Site: http://www.panasonic.co.
