Digital Video Cassette Recorder NV-DV2000EC Operating Instructions PAL VQT8649 Before attempting to connect, operate or adjust this product, please read these instructions completely.
Dear Customer Thank you for purchasing this Panasonic Digital Video Cassette Recorder. We recommend that you carefully study the Operating Instructions before attempting to operate the unit and that you note the listed precautions. As this equipment gets hot during use, operate it in well ventilated place; do not install this equipment in a confined space such as a book case or similar unit.
Contents Before Use Preparations for Editing Cautions .................................................................... 04 Caution for AC Mains Lead (for U.K.) ..................... 06 Check List .................................................................. 07 Controls and Connection Sockets ......................... 08 Editing Controller ................................................... 010 Editing Controller Setup ..........................................
Cautions Be sure to read the cautions carefully before you operate this VCR. Avoid sudden changes in temperature If the VCR is moved suddenly from a cold to a warm place, condensation may form on the tape surface and inside the VCR. If this happens, leave the VCR at room temperature for at least 1 hour before operating it. Avoid humidity and dust Do not use the VCR in very humid or dusty places. This may cause damage to its internal parts.
Before Use Using the Mini-DV format Digital Video Head Cleaner: 1.Insert the Head Cleaner into the VCR in the same way as a video cassette. 2.Press 1 (PLAY), and after approximately 20 seconds press ∫ (STOP). (Do not rewind the tape.) 3.Take out the Head Cleaner. Insert a video cassette, perform recording and then play it back to check the picture. 4.If the picture is still not clear, repeat above operation steps 1-3. (Do not use the Head Cleaner more than 3 times in succession.
Caution for AC Mains Lead (for U.K.) For your safety please read the following text carefully This appliance is supplied with a moulded threepin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-amperes and it is approved by ASTA or BSI to BS 1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse.
Before Use Check List Check that you have the accessories and items shown below. 1. VJA0733-C VJA0940 VJA1022 2. VJA1039 VJA0664-1 VJA0664-1A VJA1023 [See a leaflet.] 3. VJA0754 VJA1068 ∆ AC mains leads (3 pcs.) ∆ S-Video cable (1 pc.) VJA0658-A or VJA0748 ∆ AV cables (1 pc.) VJA0788, VJA1062, VJA0788-B or VJA0788-D ∆ Edit cable (1 pc.) VJA1109 or VJA0787 ∆ DV cable (1 pc.) VJA1012 ∆ Batteries for the Editing Controller (2 pcs.) R6 type ∆ Digital Video Head Cleaner (1 pc.
Controls and Connection Sockets This section gives a detailed explanation of the function of each button, switch and connection socket.
The scart terminal is also called “Peritel”, “Euro Connector” or “Euro AV”.
Editing Controller 1 3 2 5 6 7 4 8 9 DIGITAL VCR 10 11 01 12 13 14 SET UP button To make the SET UP screen appear on the TV screen. When the SET UP screen is displayed, use this button to return to the previous screen. 16 10 REC button (¥) [R16,39,40] To start recording. 11 Rewind button (6) [R15] In the stop mode: To rewind the tape. In the playback mode: To search backward for a scene. In the rewind mode: To view the video. “&” is lit during rewind.
18 19 20 21 Before Use 17 17 23 22 DIGITAL VCR 24 25 26 27 28 29 30 31 17 Infra-red Transmitter window 28 18 OK button To start Manual editing and to store the selection on the SET UP or EDIT MENU screen. RECORDER button [R43–51] To operate this VCR as the recording unit for editing. 29 INDEX/PHOTO buttons [R18] For the index/photoshot index search function.
Editing Controller Setup Installing the Batteries 1 To remove the cover, slide it in the direction of the arrow while pressing down. Inserting the Cassette/ Child Lock Function Be sure to insert the cassette with the window side facing upwards until it is taken into the VCR. Press EJECT and remove the cassette from the video unit. 7 8 2 Load the batteries with their polarity (+ and -) aligned correctly. d Child Lock Function e d e 3 Slide the cover back on.
Connections Using a 21-pin Scart Cable/ Connections Using an S-Video Cable The VCR send signals to the TV via a 21-pin scart cable (not supplied). Perform the connections shown in the figure below. Set NORMAL/S-VIDEO OUT to the S-VIDEO OUT when connecting the VCR to a TV set equipped with a 21-pin Euro-AV Connector with pins for separate Y/C signal input.
Connection to a Stereo Amplifier/ Connection to a Decoder Connection to a Stereo Amplifier In addition to the connections described on the previous page, connect the MONITOR OUT (AV3 OUT) sockets to the Amplifier using an AV cable. TV (Not supplied) Note: ¡ If the TV set is provided with an RGB-compatible connector, connect the 21-pin Scart cable from the VCR to this connector. Use the fully-wired 21-pin Scart cable for connecting the TV set and VCR and for connecting the VCR and decoder.
Playback DIGITAL VCR REW STOP PLAY STEREO1 AUDIO REC LEVEL FF STILL ALBUM AUDIO MIX PAUSE ¥REC/OTR INPUT SELECT 6 1 2 4,5 10 0 ST1 ST2 10 AV4 OUT PRINT Preparation ≥ Insert a recorded cassette tape. [R12] S-VIDEO VIDEO L – AUDIO – R To Locate the Desired Picture Exactly Operations 1 Press 1 (PLAY) to start playback. 1Press JOG/SHUTTLE on the Editing controller. ≥ The button on the editing controller is lit. 2Turn Jog dial. Q P 2 Press 5 (FAST FORWARD) for cue playback.
Recording DISPLAY DATE Q EDIT MENU AUDIO P M A IN T OU VIDEO JOG/ SHUTTLE RK INSERT MA RK EXIT DIGITAL VCR AUDIO DUB INPUT SELECT SETUP OK PLAYER RECORDER STEREO SELECT VCR 1 2 3 INDEX/PHOTO COUNTER RESET ZERO STOP REC REW SEARCH SELECT STOP PLAY PAUSE/ SLOW FF REW STOP PLAY STEREO1 AUDIO REC LEVEL FF STILL ALBUM AUDIO MIX PAUSE ¥REC/OTR INPUT SELECT 0 10 0 ST1 ST2 10 AV4 OUT Í/I ¥ DV2 STEREO SERECT < EJECT DV SELECT EDIT AUDIO OUT REW STOP FF STILL
Í/I ¥ DV2 STEREO SERECT < EJECT DV SELECT EDIT AUDIO OUT REW FF STILL ALBUM STEREO1 AUDIO REC LEVEL 8mm PLAY STOP AUDIO MIX PAUSE ¥ REC/OTR 1 INPUT SELECT 2 0 AV4 IN RECORDER EDIT CONTROL PLAYER PASSIVE DV EDIT 8mm S-VIDEO VIDEO MIXING EDIT SP/LP TBC 3D DNR PRINTER/ L/MONO-AUDIO-R D.STILL PICTURE SP/LP TBC 10 0 ST1 ST2 10 AV4 OUT PRINT S-VIDEO VIDEO L - AUDIO - R 3D DNR 3D DNR Functions 3D DNR is the 3-Dimensional Digital Noise Reduction Function.
Search Functions DIGITAL VCR Photoshot Index Search System Photoshot index signals are automatically recorded when a Panasonic Digital Video Camera is used for photo shot shooting. Photo shot images are searched using these signals, and when such an image is located, the image is played back as a still picture. Index Search System It is easy to find the beginning of each recording because a special index signal is recorded at the start of each recorded segment on the tape.
Using the VCR with a Video Printer Still pictures can easily be printed out when the VCR is connected to a Panasonic video printer equipped with an EDIT socket. TV (Not supplied) Video IN Video OUT EDIT Socket Video Printer (Not supplied) EDIT PRINT RECORDER PLAYER ASSIVE DV EDIT 8mm PASSIVE PRINTER/ .STILL PICTURE D.STILL Preparation ≥ Connect a Video Printer to this VCR as shown. Video Printer: 1 Turn the Video Printer on.
Using the VCR with a Computer The Personal Computer Connection Kit VW-DTA9/10E (Optional) for Digital Video Equipment performs it possible to connect the VCR to a computer and transmit still video images to it. front side ¥ DV2 EDIT DV SELECT 8mm 1 2 CONTROL RECORDER EDIT CONTROL PLAYER YER PASSIVE ASSIVE DV EDIT 8mm AV4 IN S-VIDEO AV1(TV) S-VIDEO OUT VIDEO L/MONO-AUDIO-R PRINTER/ D.STILL .
Clock Setting/Shipping Condition DIGITAL VCR The built-in clock must be set to the correct time. The built-in digital clock employs the 24-hour system. The clock backup system operates for at least 60 minutes in the event of power failure. Preparations ≥ Confirm that the TV is on and the VCR viewing channel is selected. ≥ Turn on the VCR. Operations 1 Press SET UP, and then press 34 (CURSOR) to select Clock setting and press OK.
Settings for VCR Functions The VCR indications shown on the TV screen are known as the On Screen Display (OSD). This VCR allows many settings to be made at the OSD. See [R36] for setting for Edit functions. Editing controller DIGITAL VCR 1 Audio Data Indicator 2 Audio Output Mode Indicator The Left (L) and Right (R) Indicators show which sound mode is selected with AUDIO OUT. Stereo: Both the L and R Indicators appear. Left: The L Indicator appears. Right: The R Indicator appears.
VCR display Comb filter Operations 1 Press SET UP, and then press 34 (CURSOR) to select VCR functions and press OK. Operations 1 Press SET UP, and then press 34 (CURSOR) to select VCR functions and press OK. 2 Press 341 (CURSOR) to select VCR display. 2 Press 34 1 (CURSOR) to select Comb filter. 3 Press 34(CURSOR) to select ON, OFF or DIMMED, and then press OK. ON: When VCR is turned off, the characters are lit in the VCR display.
Editing controller For Playback Operations 1 Press SET UP and press 34 (CURSOR) to select VCR functions and press OK. DIGITAL VCR 2 Press 341 (CURSOR) to select PB DNR. 3 Press 34 (CURSOR) to select LEVEL1 or LEVEL2 and press OK. LEVEL1: To ensure 3D DNR effect LEVEL2: To ensure high 3D DNR effect 4 Press EXIT to exit the On Screen Display. Settings for 3D DNR (REC DNR/PB DNR) Function For Recording Operations 1 Press SET UP and press 34 (CURSOR) to select VCR functions and press OK.
Editing Functions Using this VCR, 4 types of One-Touch-Edit, 3 types of Manual Editing and 3 types of Programme Editing can be selected. In Programme Editing, after setting the edit start/end point, editing can be performed automatically. Edit programmes can be set up to 10 scenes for each editing function (20 scenes for Assemble editing). Programme editing with Time Code enables high edit accuracy, typically within 5 frames at the edit start point (1 frame=1/25th of a second).
Editing Functions (continued) Audio Dubbing Allows the addition of the new sound on the STEREO2 track of a recorded tape. The original sound is left on the STEREO1 track. Performing the Audio Dubbing operation on a tape that was recorded in 12bit audio mode. Audio Mixing Allows the mixing of the original sound on the STEREO1 track with the new sound from the external recording source and recording the mixed sound on the STEREO2 track of a recorded tape. The original sound is left on the STEREO1 track.
Creating the Tapes for Editing In order to operate editing functions correctly, use these tapes for editing as follows: ≥ Tape on which the picture and sound have been recorded properly for about 20 seconds prior to the edit start point: [Playback unit] [Recording unit] This VCR first rewinds the tape to the section prior to the edit start point and then commences editing.
Connecting with a Panasonic Digital Video Camera Example for connecting Panasonic NV-DS25 Digital Video Camera as the playback unit, when controlling the playback unit through the NV-DV2000. AV1 (Rear) Recording Unit Playback Unit ¥ DV2 DV SELECT EDIT 8mm 1 2 RECORDER EDIT CONTROL PLAYER PASSIVE ASSIVE DV EDIT 8mm V4 AV4 IN S-VIDEO Notes: ≥ Before connecting any cables, first make sure that the power for both units is off.
Playback Unit (Digital Video Camera) 3 Turn on the DVC. Make the Time code appear on the LCD monitor or the viewfinder. Prepare the tape for playback. Recording Unit (the NV-DV2000) 1 2 3 4 Turn on the VCR. Set Edit Mode to RECORDER. Set Edit Terminal to EDIT. Press INPUT SELECT so that DV1 or DV2 after sliding DV SELECT switch 1 or 2, is selected. ≥ When performing Audio Dubbing or AV Insert, select A2, A3 or A4.
Connecting Two Digital Video Cassette Recorders (Both Panasonic models) Example for connecting two NV-DV2000, when controlling the playback VCR through the recording VCR. Refer to the diagram below and connect the cables required for the desired editing function. (Front) ¥ DV2 V2 EDIT DV SELECT 8mm 1 2 RECORDER EDIT CONTROL PLAYER ASSIVE DV EDIT 8mm PASSIVE AV4 IN S-VIDEO VIDEO L/MONO-AUDIO-R PRINTER/ .STILL PICTURE D.
Playback VCR 1 Turn on the VCR. 2 Set Edit Mode to PASSIVE. 3 Set Edit Terminal to EDIT. (Set DV SELECT to 1 or 2.) Recording VCR 1 Turn on the VCR. 2 Set Edit Mode to RECORDER. 3 Set Edit Terminal to EDIT. 4 Press INPUT SELECT so that DV1 or DV2 after sliding DV SELECT to 1 or 2, is selected. ≥ When performing Audio Dubbing or AV Insert, select A2, A3 or A4.
Connecting an S-VHS (VHS) Video Equipment with an Edit Socket Example for connecting an S-VHS (VHS) video equipment with an Edit socket as the playback unit, when controlling the playback unit through the recording VCR (this unit). Refer to the diagram below and connect the cables required for the desired editing function.
Playback Unit [S-VHS (VHS) Video Equipment with an Edit socket] 1 Turn on the Video Equipment. 2 Set the unit so that it is ready to be controlled. ≥ Read the operating instructions of the playback unit and make the necessary settings. Recording VCR (the NV-DV2000) 1 Turn on the VCR. 2 Set Edit Mode to RECORDER. 3 Set Edit Terminal to EDIT. 4 Press INPUT SELECT so that A2, A3 or A4 is selected.
Connecting a Video Equipment with a LANC Socket Example for connecting another manufacturer’s video equipment with a LANC terminal (L control) as the playback unit, when controlling the playback unit through the VCR. ¥DV2 DV SELECT EDIT 8mm 1 2 AV1 (Rear) RECORDER EDIT CONTROL PLAYER PASSIVE DV EDIT 8mm AV4 IN S-VIDEO VIDEO L/MONO-AUDIO-R PRINTER/ D.STILL PICTURE 8mm Playback Unit with a LANC socket (8mm Video Camera etc.
Recording VCR (the NV-DV2000) 1 Turn on the Video Equipment. 1 Turn on the VCR. 2 Set the unit so that it is ready to be controlled. ≥ Read the operating instructions of the playback unit and make the necessary settings. 2 Set Edit Terminal to 8mm. 3 Press INPUT SELECT so that A3 or A4 is selected. ≥ If the playback unit is connected to the external input on the rear of the NV-DV2000, select A2. ≥ Press INPUT SELECT so that DV1 or DV2 after sliding DV SELECT to 1 or 2, is selected.
Settings for Editing This VCR also allows some settings for editing to be made at the On Screen Display (OSD). Audio mode Operations 1 Press SET UP. DIGITAL VCR Preparations ¡ Confirm that the TV is on and the VCR viewing channel is selected. ¡ Complete necessary connections and settings. [R28–35] Search with Sound Operations 1 Press SET UP. 2 2 Press 34(CURSOR) to select Edit functions and press OK. 3 Press 34(CURSOR) to select Audio mode and press OK.
Setting for One-Touch-Edit Operations 1 Press SET UP. 2 Press 34 (CURSOR) to select Edit functions and press OK. 3 Press 34 (CURSOR) to select One-TouchEdit and press OK. 4 Press 21 (CURSOR) to select OFF or ON, and then press OK. SET UP Edit functions VCR functions Clock setting Shipping conditon Edit functions Search with Sound Audio mode One-Touch-Edit Still Album One-Touch-Edit OFF ON OFF: Select this whenever you are performing any editing function other than One-Touch-Edit.
Album Function The album function lets you collect desired scenes (both moving and still pictures) and create the equivalent of a photo album but on a video cassette. The pictures can be copied onto the cassette from a video movie camera, a digital still camera or another VCR for any period of time that can preset.
Editing when Not Using an Edit Cable To connect a VCR or Video Movie Camera without an Edit socket and use the NV-DV2000 as the Recording VCR. 2 4 DIGITAL VCR OK 6 Preparations ≥ Complete necessary connections and settings. [R28–35] ≥ Connect the AV1 socket on the NV-DV2000 to the TV. ≥ Connect the AV2 socket or the AUDIO/VIDEO/SVIDEO IN (AV3/AV4) sockets on the NV-DV2000 to the playback unit.
One-Touch Assemble If the One-Touch Edit function is used, Assemble editing can be performed by controlling the playback unit through the NV-DV2000. 1,5 DIGITAL VCR 3 2,4 6 Preparations ≥ Confirm that the TV is on and the VCR viewing channel is selected. ≥ Complete necessary connections and settings. [R28–35] ≥ Set One-Touch-Edit to ON on Edit functions menu. [R37] Operations 1 Press JOG/SHUTTLE on the Editing controller, and check that the button is lit.
One-Touch Insert/Audio Dubbing If the One-Touch Edit functions is used, Insert (Video Insert, Audio Insert, and AV Insert) and Audio Dubbing can be performed by controlling the playback unit through the NV-DV2000. 3 1,5 DIGITAL VCR STEREO SERECT < EJECT ¥ DV IN/OUT DV SELECT EDIT AUDIO OUT REW PLAY STOP AUDIO REC LEVEL 8mm CONTROL STEREO1 AUDIO MIX FF STILL ALBUM PAUSE ¥ REC/OTR 1 INPUT SELECT 2 0 RECORDER EDIT CONTROL 8mm PLAYER PASSIVE DV EDIT CONTROL MIXING EDIT AV4 PRINTER/ D.
One-Touch Audio Mixing This function is used to mix the audio on STEREO1, which has already been recorded, with audio from a external recording source (A2, A3 or A4), and record the result on STEREO2. This function is useful for adding new audio, such as music or a narration, to the original audio which has already been recorded.
Manual Copying This function can be used to copy tapes between digital video equipments with practically no deterioration in quality. This function can also copy a tape that was recorded in S-VHS (VHS) format onto a digital video tape. 1,9 2,7 3,5 09 Press EDIT MENU to stop editing. ≥ Operation now returns to the screen which appears in step 3. This makes it possible to continue with editing or change the point at which editing is to start. 10 Press EXIT. ≥ The On Screen Display disappears.
Manual Insert This function is used to replace the picture and sound on a recorded tape. Press EDIT MENU to stop editing. ≥ Operation now returns to the screen which appears in step 3. This makes it possible to continue with editing or change the point at which editing is to start. 10 Press EXIT. ≥ The On Screen Display disappears. 3,5 1,9 2,7 09 DIGITAL VCR 3 5 4,6 Preparations ¡ Confirm that the TV is on and the VCR viewing channel is selected. ¡ Complete necessary connections and settings.
Manual Audio Dubbing This function is used to add new sound on the STEREO2 track of previously recorded tape. 1,9 2,7 09 Press EDIT MENU to stop editing. ≥ Operation now returns to the screen which appears in step 3. This makes it possible to continue with editing or change the point at which editing is to start. 10 Press EXIT. ≥ The On Screen Display disappears. 3,5 DIGITAL VCR To Listen to the Edited Audio after Audio Dubbing 5 4,6 Press STEREO SELECT during playback and select STEREO2.
Programme Assemble This function can be used to link together desired scenes on a tape. This function can also be used to skip unnecessary scenes recorded on a tape and copy them onto a separate tape. 4,7 5,8 1 2,3,10,11 6 DIGITAL VCR 4 7 Preparations ≥ Confirm that the TV is on and the VCR viewing channel is selected. ≥ Complete necessary connections and settings. [R28–35] Operations 1 Press EDIT MENU. 2 Press 34 (CURSOR) to select Programme Editing, and then press OK.
10 11 Press 34 (CURSOR) to select Start Assemble to start editing, and then press OK. ≥ Editing begins after the playback unit and the recording VCR both rewind their tapes to the edit start points. After completing editing, press 34(CURSOR) to select Review, and then press OK. ≥ The edited pictures are played back.
Programme Insert This function is used to replace the picture and sound on a recorded tape. 1 2,3,10,11,12 4,7 5,8 6 DIGITAL VCR 4 7 Preparations ≥ Confirm that the TV is on and the VCR viewing channel is selected. ≥ Complete necessary connections and settings. [R28–35] 5,6,8 05 Search for the edit start point on the playback unit and press MARK IN. V i deo I ns er t 1 ; PLAYER 0h16m 39s 19f 0h16m 39s 19f h m s f In O ut Example: Video Insert 06 Operations 01 Press EDIT MENU.
10 Press 34 (CURSOR) Video Insert to select Preview to Confirm/Change Insert a programme confirm the editing Erase a programme Preview operation before Start Insert performing actual Review Timing Adjust editing, and then press OK. ≥ Preview begins after the playback unit and the recording VCR both rewind their tapes to the edit start points. 11 Press 34 (CURSOR) to select Start Insert to start editing, and then press OK.
Programme Audio Dubbing This function is used to add new sound on the STEREO2 track of previously recorded tape. 1 2,3,10,11,12 4,7 5,8 6 DIGITAL VCR 4 7 Preparations ≥ Confirm that the TV is on and the VCR viewing channel is selected. ≥ Complete necessary connections and settings. [R28–35] 5,6,8 07 Press RECORDER and JOG/SHUTTLE. ≥ The picture from the recording VCR appears on the screen. 08 Search for the edit start point on the recording VCR and press MARK IN. Operations 01 Press EDIT MENU.
Press 34 (CURSOR) to select Start Dubbing to start editing, and then press OK. ≥ Editing begins after the playback unit and the recording VCR both rewind their tapes to the edit start points. Audio Dubbing Confirm/Change Insert a programme Erase a programme Preview Start Dubbing Review Timing Adjust Au d i o D u bb i n g 1 RECORDER ¥ 1 PLAYER Dubbing in Progress 12 After completing editing, press 34 (CURSOR) to select Review, and then press OK. ≥ The edited sounds are played back.
Other Editing Functions To Insert a New Programme Between Existing Programmes: DIGITAL VCR 1 Press 34 (CURSOR) to select Insert a programme, and then press OK. ≥The programme list is displayed. 2 Press 34 (CURSOR) to select the programme number where a programme is to be inserted, and then press OK. ≥The Insert a programme screen is displayed. Once all programme settings are completed, the screen shown below is displayed.
To Cancel All Editing Programmes: Press EDIT MENU twice. 2 Press 34 (CURSOR) to select Erase all programmes, and then press OK. ≥ The Erase all programmes screen is displayed. 3 Press 21 (CURSOR) to select YES, and then press OK. ≥ The screen returns to the Programme Editing menu. ≥ After the message indicating that “All programmes have been erased.” appears on the screen, operation returns to the EDIT MENU screen.
Edit Timing Adjustment When performing editing in conjunction with a unit which has a different mechanism, there may be a lag in the edit start point due to a deviation between the time a pause cancellation signal is received by the recording unit and the time recording actually begins. Edit Timing Adjustment is used to compensate the edit start and end time in light of this start-up time deviation.
DIGITAL VCR Manual Editing If there is a deviation in the results of a manual editing operation, the timing of the edit start (In) position on the playback unit can be adjusted by approximately d1 second. Perform the procedure described below when setting an edit start point in any editing mode. Example: Manual Copying 1 Press EDIT MENU. 2 Press 34 (CURSOR) to select Copying, and then press OK.
Tape Trade Editing When performing a Programme Editing after this VCR and Panasonic Digital Video Camera have been connected using an Edit cable and a DV cable (cable for sending video and audio signals), this function enables the Editing controller of this VCR to set the edit points for the playback unit.
Glossary of Terms Audio Dubbing You can record two audio tracks (Stereo 1 and Stereo 2) on a tape that is recorded in 12bit audio mode. (When the tape is first recorded, the audio is recorded only in the Stereo 1 track.) The Audio Dubbing function allows you to add new, separate audio in the Stereo 2 track. Audio Mixing You can record two audio tracks (Stereo 1 and Stereo 2) on a tape that is recorded in 12bit audio mode. (When the tape is first recorded, the audio is recorded only in the Stereo 1 track.
DV TERMINAL This terminal is used to input/output video and audio data on digital video equipment. Because the video and audio data is sent through the DV cable as digital signals, there is practically no deterioration in video and audio quality after copying.
On Screen Display Messages [Please insert video tape.] ‘ ¥ (REC/OTR), 1 (PLAY), 5 (FAST FORWARD), 6 (REWIND) or JOG/SHUTTLE is pressed when no cassette is in the VCR. Insert a video tape. [Recording not allowed. Check setting of the recordprevention tab.] ‘ ¥ (REC/OTR) has been pressed when using a cassette with the opened record-prevention tab. Use a cassette with the closed record-prevention tab. Messages of On Screen Display for Editing Operations [Please insert video tape.
Before Requesting Service Before requesting service, check the following points once again. VCR does not operate correctly The symptom description is indicated in quotation “ ”. “VCR display is not illuminated.” ‘ Mains lead is not connected. Reconnect mains lead to VCR. ‘ VCR display setting is OFF. Set VCR display to ON or DIMMED. [R23] Playback does not operate correctly The symptom description is indicated in quotation “ ”.
“Cannot set programme” ‘ Have the maximum number of programmes already been set? “A set programme is skipped” ‘ Are there at least 4 seconds between the edit start point and the end point? Editing may not be performed properly for a programme with a set duration of less than 4 seconds. “Cannot adjust the edit timing” ‘ The timing cannot be adjusted if the playback unit that is connected does not have a Time code or tape (linear) counter display.
Flow Chart for On Screen Displays SET UP On Screen Displays Edit functions Edit functions VCR functions Clock setting Shipping condition 34 : select , OK : access EXIT : leave menu Search with Sound Audio mode One-Touch-Edit Still Album 34 : select , OK : access SET UP : return VCR functions Edit functions VCR functions Clock setting Shipping condition 34 : select , OK : access EXIT : leave menu OSD VCR display Colour mode Comb filter TBC REC DNR PB DNR Remote : : : : : : : : AUTO DIMMED COLOUR ON
EDIT MENU On Screen Display (Manual Editing ) Copying ; 34 : select , OK : access EXIT : leave menu EDIT MENU Copying Video Insert Audio Insert AV Insert Audio Dubbing Programme Editing EDIT MENU 34 : select , OK : access EDIT MENU : return EDIT MENU : stop PLAYER RECORDER ∫ Video Insert 1 PLAYER Insert in Progress 34 : select , OK : access EDIT MENU : return EDIT MENU : stop PLAYER RECORDER ∫ Audio Insert 1 PLAYER RECORDER ¥ Start Insert Timing Adjust Insert in Progress 34 : select ,
Flow Chart for On Screen Displays (continued) Programme Editing On Screen Displays Programme Editing Assemble Video Insert Audio Insert AV Insert Audio Dubbing Assemble [Page1] 1 ; PLAYER 0h16m 38s 20f In 0h16m 38s 20f Out 0h18m 09s 13f Assemble [Page1] 1 ; PLAYER 0h18m 09s 13f In 0h16m 38s 20f Out 0h18m 09s 13f Erase all programmes 34 : select , OK : access EDIT MENU : return 1 : next OK : done , EDIT MENU : return Programme Editing Assemble Video Insert Audio Insert AV Insert Audio Dubbing 1 : next
34 : select , OK : access EDIT MENU : return Video Insert Assemble [Page1] 1 RECORDER In ; 0h12m 24s 12f 0h12m 24s 12f OK : done , EDIT MENU : return Video Insert In Out ; 0h05m 22s 10f 0h05m 22s 10f 0h18m 09s 13f 1 : next OK : done , EDIT MENU : return Audio Insert In Out ; 0h01m 31s 08f 0h01m 31s 08f 0h18m 09s 13f 1 : next OK : done , EDIT MENU : return In Out ; 0h03m 46s 08f 0h03m 46s 08f 0h18m 09s 13f 1 : next OK : done , EDIT MENU : return In Out Confirm/Change Insert a programme
Specifications NV-DV2000EC Power Source: Power Consumption: Power Consumption When in Standby Mode: (with display off mode) Video Recording System: Audio Recording System: Video Heads: Tape Speed: Tape Format: Record/Playback Time: FF/REW Time: VIDEO Television System: Modulation System: Input Level: Output Level: AUDIO Input Level: Output Level: Audio Track: Digital Still Picture: Digital Interface: Audio Frequency Response: Operating Temperature: Operating Humidity: Weight: Dimensions: Standard Access
E Printed in Japan D F0600Gy0 ( 1500A ) Matsushita Electric Industrial Co., Ltd. Central P.O.
