Panasonic^ Operating Instructions Commercial Microwave Ovens Model NE-1054T NE-1024T Before operating this oven, please read these instructions completely.
TABLE OF CONTENTS PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY.................................................................................................................... 3 IMPORTANT SAFETY INSTRUCTIONS.......................................................................................... 3 Installation and Grounding Instructions............................................................................................. 4 Safety Precautions................................
IMPORTANT SAFETY INSTRUCTIONS much care as you use with a stove or any other cooking device. Your microwave oven is a cooking device and you should use as 9. Do not allow children to use this appliance, unless closely supervised by an adult. When using this electric appliance, basic safety precautions should be followed, including the following: 10. Do not operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped.
INSTALLATION AND GROUNDING INSTRUCTIONS Examine Your Oven Wiring Requirements Unpack oven, remove all packing material, and examine the oven tor any damage such as dents, broken door latches or cracks in the door. Notify dealer immediately if oven is damaged. DO NOT install if oven is damaged. 1.
Food General Use 1. It is better to UNDERHEAT RATHER THAN OVERHEAT foods. If food is underheated, it can always be returned to the oven for further heating. If food is overheated, nothing can be done. Always start with minimum heating times. 1. DO NOT tamper with or make any adjustments or repairs to door, control panel housing, safety interlock switches or any other part of the oven. Do NOT remove outer panel from oven. Repairs should only be done by a qualified service person. 2.
Microwaves are a form of high frequency radio waves simiiar to those used by a radio including AMi FM and CB. They are, however, much shorter than radio waves; approximately five inches long. Electricity is converted into microwave energy by the magnetron tube. From the magnetron tube, microwave energy is transmitted and absorbed. Absorption During heating, microwaves will be absorbed by food. They penetrate to a depth of about 7< to 1 '/î-inches.
Control Panel m I o N) H ® Oven Window ® Oven Lamp © Splash Guard/Light Diffuser ® Timer ® Control Panel ® Door Safety Lock System How to Operate 6. 1. Make sure unit is plugged into a three-prong grounded 120 V circuit. When time has elapsed, a bell will ring and the unit will turn off. >■ Oven light turns off. 2. Open the door. PLACE CONTAINER OF FOOD in the oven. NOTE: 3. CLOSE THE DOOR securely. 1. If heating is completed BEFORE the timer has elapsed, turn the TIMER TO "0" position.
NE-1054T Control Panel Ti lO o Digital Display Window (see below) Memory Pads (3) Power Level Selector Pad (4) PROG.
Before Operating Make sure the oven is connected to a properly grounded electrical outlet. vVnen the door is closed, the Display Window is still blank. When the door is opened, the Display Window shows "0”, =or the detail operation, see the page on each feature. This oven is preset at the factory for the following: ■ Memory Pads are preset to High Power for the indicated heating times for single stage heating. 6 - 1 min. 30 sec. 72 min. 82 min. 30 sec. 93 min. 0-3 min. 30 sec. 1- 10 sec. 2- 20 sec.
How to Operate HEATING -----------------------------------------------------------------------------------------------------------------------------------Open the door and place food in the oven cavity. Close the door. “0” must be showing in the Display Window. A. Manual Single Stage Heating: This feature gives the user maximum flexibility to set the oven to desired heating time and power level. Ideal for menus that require various heating requirements.
C. Programmed Heating: Example: 1 stage; Memory Pad 9 to heat for 3 minutes at HIGH Power Display Window 1. 2. E[ 3:00 START 3. Beep tone will sound. •Press the Memory Pad 9. In Program Lock Mode oven will start without pressing START Pad. See page 15. •Press the START Pad. Heating will start. The time in the Display Window will count down. •Ail heating will stop. When opening the door, the display will stop blinking.
How to Operate Programming------------ ---------------------------------------------------------------------------Display Window — DO NOT OPEN THE DOOR — The Display Window MUST be blank before programming can begin. If any Indicator light is illuminated in the digital Display Window: Close the door, press STOP/RESET Pad and wait 1 minute until the Display Window goes blank. A.
How to Operate NOTE: • Program the remaining Memory Pads as desired by repeating steps 1-5. You may insert up to 10 memory Programs. •When the PROG indicator is blinking, the program can be cancelled and/or the Pad erased by pressing the STOPfflESET Pad. B. Programming Memory Pads for 2 or 3 Stage Heating: Example: To program for 2 minutes at DEFROST for 2 stage heating using Memory Pad Numbers Display Window 1. Complete Steps 1 to 4 on page 12, 30 PROG 1 2 •Press the POWER Level Selector Pad 5 times.
C. Programming the Double Quantity Pad — For multiple portion heating: Your oven is factory set to automatically double the programmed time for multiple portion heating — this is the correct setting for heating multiple portions of most small foods items. No further programming of the time is necessary for these food items. The time required to heat multiple portions of some large platters and most bulk food loads is slightly less than double that of a single portion.
other Features A. To Activate Program Lock: Display Window This procedure “Locks” the control panel Memory Pads Into their programmed heating times and power levels. DO NOT OPEN THE DOOR. The Display Window must be blank before the Program Lock feature can be activated. 1. •Press and hold in the PROG. Pad until the display shows 'P' and “L". (for 6 seconds) PROG. •Program Lock feature is now activated. PL NOTE: *Do not press PROG.
To Read Program List: Allows you to review all currently programmed Pad Number, heating time and power level for each stage. Display Window 1. Open the door. STOP/RESET + 0 •While pressing the STOP/RESET Pad, press and hold in the START Pad. The Beep Tone setting will show in the Display Window. Example: Stage Indicator 1: Beep tone is ON bEEP START Stage Indicator 2: Beep tone is OFF 2 seconds later, the Program Lock setting will show in the Display Window.
How to Opsrate D. To Select Beep Tone Options; Display Window The Beep Tone can be set, ON or OFF. 0 1. Open the door. 2, PROG. 3. •Press the PROG. Pad. The display will not change. 0 •Press the Memory Pad 0. 3:30 bE EP •Repeat pressing of 0 Pad. Select “OFF” of Beep Tone. Stage Indicator 1 = ON Stage Indicator 2 = OFF PROG L 4. PROG. •Press the PROG. Pad again. You have completed programming the beep tone, 2 bE EP o PROG_? bEEP •2 seconds later, the Display Window wl/l go blank. E.
This oven monitors its operation and displays a Failure Code in the Display Window when a problem occurs. What to do when a failure code appears: CODE CAUSE F01 •Overcooked food *Temperature of exhaust air too high. ‘Press STOP/RESET Pad to stop beep. ‘Wait for oven to cool down and reset, ‘If a flame is present, do not open oven door. ‘If normal operation does not resume, call the service agent with information of failure code.
Technical Spectflcations NE-1054T ! NE-1024T 120V, 60 Hz, single phase Power Source 13.4A Required Power 1500W 1000 w Output* Frequency 2,450 MHz . Outer Dimensions 1 (H X W X D) 12" x20Ve" X 14Vi" 306 mm X 510 mm X 360 mm ; Cavity Dimensions (H X W X D) 8'/ie" X 13" X 13" 205 mm X 330 mm x 330 mm Net Weight Approximately 34 lb {15.4 kg) Shipping Weight Approximately 39 lbs (17.
PANASONIC CONSUMER ELECTONIC COMPANY COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way, 4A-4, Secaucus, NJ 07094 (201) 348-5377 T00036P00AP Printed in Taiwan
