Operating instructions
24 - Maintenance
Maintenance
Cleaning the water-supply
filter
Clean the filter if water is not supplied
properly.
Turn the tap off.1.
Switch on the appliance.2.
Select the Cotton programme, and 3.
then press the Start button.
After 1 minute, switch off the 4.
appliance. Water has drained out of
the water-supply hose.
Disconnect the water-supply hose 5.
from the appliance.
Clean the filter, which is on the rear 6.
of the appliance.
Use a small brush, for example, a
toothbrush.
If the unit is supplied with the hose 7.
fitted with a water-supply valve turn
off the tap supplying the appliance,
disconnect the hose from the tap,
and then clean the filter on hose in
the same way.
Reconnect the water-supply hose.8.
Tighten the plastic joint firmly.
Turn on the tap, then check for leaks.9.
Preventing a frozen
water-supply hose
If the appliance is delivered in freezing
weather conditions, after setting up, leave
it at room temperature for 24 hours before
using. This will ensure that the
water-supply hose does not get clogged up
with ice.
If your water-supply hose freezes, perform
the following procedures:
Wrap warm towels around the joints 1.
of the water-supply hose.
Add 2 to 3 litres of warm water to the 2.
drum.
Start washing with the Drain only 3.
function, using the Mode button. (See
page 20.)
Joints
Tap
Water-supply hose
about
50 °C
NA-140VG4_English_UK.indb 24 2012-6-13 18:45:19
24 - Maintenance
Maintenance
Cleaning the water-supply
filter
Clean the filter if water is not supplied
properly.
Turn the tap off.1.
Switch on the appliance.2.
Select the Cotton programme, and 3.
then press the Start button.
After 1 minute, switch off the 4.
appliance. Water has drained out of
the water-supply hose.
Disconnect the water-supply hose 5.
from the appliance.
Clean the filter, which is on the rear 6.
of the appliance.
Use a small brush, for example, a
toothbrush.
If the unit is supplied with the hose 7.
fitted with a water-supply valve turn
off the tap supplying the appliance,
disconnect the hose from the tap,
and then clean the filter on hose in
the same way.
Reconnect the water-supply hose.8.
Tighten the plastic joint firmly.
Turn on the tap, then check for leaks.9.
Preventing a frozen
water-supply hose
If the appliance is delivered in freezing
weather conditions, after setting up, leave
it at room temperature for 24 hours before
using. This will ensure that the
water-supply hose does not get clogged up
with ice.
If your water-supply hose freezes, perform
the following procedures:
Wrap warm towels around the joints 1.
of the water-supply hose.
Add 2 to 3 litres of warm water to the 2.
drum.
Start washing with the Drain only 3.
function, using the Mode button. (See
page 20.)
Joints
Tap
Water-supply hose
about
50 °C
NA-140VG4_English_UK.indb 24 2012-6-13 18:45:19
24 - Maintenance
Maintenance
Cleaning the water-supply
filter
Clean the filter if water is not supplied
properly.
Turn the tap off.1.
Switch on the appliance.2.
Select the Cotton programme, and 3.
then press the Start button.
After 1 minute, switch off the 4.
appliance. Water has drained out of
the water-supply hose.
Disconnect the water-supply hose 5.
from the appliance.
Clean the filter, which is on the rear 6.
of the appliance.
Use a small brush, for example, a
toothbrush.
If the unit is supplied with the hose 7.
fitted with a water-supply valve turn
off the tap supplying the appliance,
disconnect the hose from the tap,
and then clean the filter on hose in
the same way.
Reconnect the water-supply hose.8.
Tighten the plastic joint firmly.
Turn on the tap, then check for leaks.9.
Preventing a frozen
water-supply hose
If the appliance is delivered in freezing
weather conditions, after setting up, leave
it at room temperature for 24 hours before
using. This will ensure that the
water-supply hose does not get clogged up
with ice.
If your water-supply hose freezes, perform
the following procedures:
Wrap warm towels around the joints 1.
of the water-supply hose.
Add 2 to 3 litres of warm water to the 2.
drum.
Start washing with the Drain only 3.
function, using the Mode button. (See
page 20.)
Joints
Tap
Water-supply hose
about
50 °C
NA-140VG4_English_UK.indb 24 2012-6-13 18:45:19
24 - Maintenance
Maintenance
Cleaning the water-supply
filter
Clean the filter if water is not supplied
properly.
Turn the tap off.1.
Switch on the appliance.2.
Select the Cotton programme, and 3.
then press the Start button.
After 1 minute, switch off the 4.
appliance. Water has drained out of
the water-supply hose.
Disconnect the water-supply hose 5.
from the appliance.
Clean the filter, which is on the rear 6.
of the appliance.
Use a small brush, for example, a
toothbrush.
If the unit is supplied with the hose 7.
fitted with a water-supply valve turn
off the tap supplying the appliance,
disconnect the hose from the tap,
and then clean the filter on hose in
the same way.
Reconnect the water-supply hose.8.
Tighten the plastic joint firmly.
Turn on the tap, then check for leaks.9.
Preventing a frozen
water-supply hose
If the appliance is delivered in freezing
weather conditions, after setting up, leave
it at room temperature for 24 hours before
using. This will ensure that the
water-supply hose does not get clogged up
with ice.
If your water-supply hose freezes, perform
the following procedures:
Wrap warm towels around the joints 1.
of the water-supply hose.
Add 2 to 3 litres of warm water to the 2.
drum.
Start washing with the Drain only 3.
function, using the Mode button. (See
page 20.)
Joints
Tap
Water-supply hose
about
50 °C
NA-140VG4_English_UK.indb 24 2012-6-13 18:45:19
Održavanje
Čišćenje ltra za dovod vode
Očistite ltar ako dovod vode nije posve
ispravan.
1. Zatvorite slavinu.
2. Uključite uređaj.
3. Odaberite program Cotton i pritisnite
gumb Start.
4. Isključite uređaj nakon 1 minute.
Voda je istekla iz cijevi za dovod
vode.
5. Odspojite cijev za dovod vode iz
uređaja.
6. Očistite ltar koji se nalazi na
stražnjoj strani uređaja.
Upotrijebite malu četku, npr. četkicu za
zube.
7. Ako uređaj bude isporučen tako
da je na cijev stavljen ventil za
dovod vode, isključite dovod vode,
odspojite cijev od slavine i na isti
način očistite ltar na cijevi.
8. Ponovno spojite cijev za dovod vode.
Čvrsto stegnite plastične spojeve.
9. Uključite dovod vode i provjerite curi
li voda.
Sprečavanje smrzavanja
cijevi za dovod vode
Ako se uređaj dostavlja pri izuzetno niskim
temperaturama, nakon što ga postavite,
ostavite ga na sobnoj temperaturi 24
sata prije prve uporabe. Time ćete izbjeći
začepljenje cijevi za dovod vode ledom.
Dođe li do zamrzavanja cijevi za dovod
vode, učinite sljedeće:
1. Omotajte tople ručnike oko spoja
cijevi za dovod vode.
2. Dodajte 2 do 3 litre tople vode u
bubanj.
3. Započnite pranje s funkcijom Drain
only, pomoću gumba Mode. (Vidi 20.
stranicu)
24 - Održavanje
Spojevi
Slavina
približno
50 °C
Cijev za dovod vode