CAUTION FOR AC MAINS LEAD (UK and Republic of Ireland only) IMPORTANT SAFETY INSTRUCTIONS FOR THE USER PARTS IDENTIFICATION HOW TO ASSEMBLE YOUR VACUUM CLEANER A} Handle Assembly / Hose Assembly / Mains Lead Storage B} How to Attach and Detach Upholstery Attachment C) Features * Automatic Height Adjustment.. * Edge Cleaning * Overload Protection .
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This appliance is supplied with a molded three pin mains plug for your safety and convenience. A fuse is fitted in this plug. Should the fuse need 1o be replaced please ensure that the replacement fuse has a rating of 13-ampere and that it is approved by PASTA or BSI to BS1362. Check for the PASTA mark or the Bismark ¥ on the body of the fuse. I the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
B DO NOT leave the vacuum cleaner plugged into the socket outlet. The plug must be removed from the socket pullet before cleaning or maintaining the appliance. B This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or frack of experience and knowledge, unless they have been given supervision ar instruction concerning use of the appliance by a person responsible for their safety.
Dust Bin Han die Filter Refresher Handle .
1. Remove tape and screw from the body. the vacuum . Insert the base of the 3. Insert the connection pipe handle into the top of body as shown. Push in handle and ta suction inlet. Ensure that the 2 hanks of the connection pipe are completely fitted into the cleaner tighten the screw. suction inlet, IMPORTANT: DO NOT over tighten the S Crew.
= s Automatic Height Adjustment Q Overload Protection Shadow Pile Carpet / | Pivot / Deep Pile Carnot Edge Cleaning Overpaid Protection Reel Bunion + Your Panasonic vacuum clearer is designed with an Automatic Height Adjustment, which adjusts the cleaning head to the proper height of any carpet pile.
IMPORTANT: To avoid any possible damage to the mains lead, never run over the mains lead or allow it to become caught in the beater bar, 2. Fix the mains lead into the cord clip to help secure i during use and turn back the upper cord hook in the upright position. Plug the mains lead into the socket outlet. vacuum clanger @ \ + Slide the Selection Switch to the right to the selected position to turn the + When finished vacuuming, slide the Selection Switch to the left until the "OFF” position.
CAUTION To prevent damaging carpeted floors, tiled floors, Linoleum, tee, do not leave the baster bar rotating in the same place for too jog.
CAUTION While using the tools, hold the handle with one hand to avid pulling the vacuum cleaner over, While using the tools, always grasp the curved wand and not the totals or the hose. &WARNING Electrical Shock or Personal Injury Hazard Disconnect the electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting.
NOTE: Lid Molding Bracket + Clean up outer dust bin with clean, soft cloth that has been dipped in water and wrung dry. Place dust bin back into vacuum cleaner by inserting the bottom first and tilting back. s Push forward and lower dust bin handle to lock dust bin in place. Ali holding bracket is located on the hinge area of the dust bin. « This bracken may release in order to prevent damage to the dust bin or the dust bin plate due to the dust bin was dropped or the dust bin plate getting any impact.
Lid HEAP Filter Unit Buckle Dust Bin + Check HEAP filter unit frequently and clean when dirty. Remove HEAP filter unit from dust bin by pulling both buckle as shown. Clean HEAP filter unit by gently tapping over a rubbish container. “Tap on Lid several sides to ensure best cleaning. DO NOT clean the HEAP filter unit by brush or clean it with water.
HEAP Exhaust Filter O A HEAP Exhaust Filter The HEAP exhaust filter removes dirt from exhaust air. + Check HEAP exhaust filter after emptying dust bin Replace when dirty. + Lay down the vacuum cleaner as shown. + To remove filter cover, slide upwards the buckle as shown, + By holding the fitter cover as shown, pull it out towards you, « Grasp the HEAP exhaust filter and pull out 10 remove it. « To install a new HEAP filter or replace the current one. put it into its original position.
TO CORRECT PROBLEMS: thermal protector to reset autocratically. + If a clog prevents the normal flow of air to the motor, the thermal protector trips and turns the mayor oft automatically. This flows the motor to cool in order to prevent possible damage to the vacuum cleaner. « Turn the vacuum cleaner off and unplug the mains lead from the socket outset to allow the vacuum cleaner to coot and the + Check for and remove clogs, if necessary.
Unplug the mains lead from socket outlet. Clean exterior using a clear, soft cloth that has been dipped in water and wrung dry. Dry wipe after above cleaning. DO NOT drip water on the vacuum cleaner. DO NOT clean tools in dishwasher or clothes washer. Wash tools in warm water, rinse and air dry. DO NOT use toils if they are wet. Loop new belt around motor shaft and beater bar belt groove. Reinstall the beater bar by inserting the end cap of the beater bar to the slot for both side.
Connection Pipe Hook Suction Inlet Cussed Wand Holder —— Nozzle Hose Upper Fitter Dust intake connection \f the vacuum cleaner does not seem to have adequate suasion, first chickweed if the dust bin is full or if a filter Is clogged. « Check the hose area. . Remove hose by grasping the curved wand, twisting, and pulling straight off. Then, press both hooks and pule out the connection pipe from the suction inlet. » Visually inspect the hose and the base area into which the hose is connected.
A WARNING Electrical Shock or Personal Injury Hazard Disconnect the electrical supply before servicing or cleaning the vacuum cleaner, Failure to do so could result in electrical shock or persona injury from vacuum cleaner suddenly starting. service representative. Review this chart to find do-it-yourself solutions for minor performance problems, Any service needed, other than those described in these Operating Instructions, should be performed by an authorized tripped. Vacuum Cleaner won't | 1.
