Operating Instructions Vacuum Cleaner MC-E581K, MC-E582K, MC-E583K MC-E581, MC-E582, MC-E583 Panasonic We would particularly advise that you carefully study these Operating Instructions before attempting to operate the unit and that you note the Important Safety Instructions. Firebase esp in a safe place with your Authorized Dealer Service booklet. This product complies with the directives 73/23/EEC and 89/336/EEC and with the Australian Standards AS 3350.2.
« Caution for AC Mains Lead (UK, IRL only} 2 « important Safety instructions for the user 3 » Cautions .
When using this vacuum cleaner, please observe these basic precautions. WARNING: To reduce the risk of fire, electric shock, or injury: + Do ot leave the vacuum cleaner plugged in to mains socket. Unplug from the socket when not in use and before cleaning the appliance or undertaking maintenance operations. « Electric shocks can scout If used outdoors or on wet surfaces.
A-1) Han die D) Dust sensor indicator (MC-E583K, MC-E583 any) C) ON/OFF Switch and Variable power control Release button Exhaust cover / Clean alr fitter Cleaning head Furniture guard Dust bag Panasonic (online stirring DIRECT For Accessories and Consumables visit our web site at www.panasonic.co.
HOW TO ASSEMBLE / OPERATE YOUR CLEANER Man die screw Dusting brush 1} Remove the dusting brush 2) Insert the base of the handier into 3) Re-install the dusting brush from the handle and align it the top of the body of the cleaner in its storage position. with the body of the cleaner in as shown. Push in the handle and Pace the hose around the the proper position as shown tighten the screw, hose clip and push inwards in the illustration. IMPORTANT: Do not over tighten o secure.
The sliding button located on the control panel is used 1o switch the vacuum cleaner ON/OFF and vary the motor speed depending on the suction required. Mod.: MC-E581K, MC-E581, MC-E582K, MC-E582 Ta switch ON, side the button sideways at “MIN” position. By sliding the button further sideways the power will gradually be increased. Mod.: MC-E583K, MC-E583 To switch ON, side the button sideways at “AUTO” position.
To tower the body of the cleaner, step on the toot release pedal @ on the bottom left corner of the vacuum cleaner. Once the body is reclined, press the beater bar pedal @ in the “ON” position and the beater bar will start to rotate. . i If you wish to stop the beater bar simply return the cleaner into the upright position. In case you want 1o stop the beater bar whilst the cleaner is in the reclined position, press the beater bar pedal in the "OFF” position. . 1. Upright position / on board 2.
1. When using the accessories always keep the vacuum cleaner in the upright position, making grue the beater bar {s in the OFF position, the hose from the suction pips inlet and remove it from the hose clip. Then slide the hose through the hose support and connect any accessory as illustrated below. NOTE: After using the accessories, re-insert the hose through the hose clip and connect back into the suction pipe inlet.
MAINTENANCE AND SERVICING IMPORTANT NOTE: Before servicing any part, always DISCONNECT THE CLEANER FROM THE MAINS SUPPLY 1) Push the release the cardboard 3) Install the dust bag by Button on the dust on the dust bag and pressing the cardboard cover as shown, and put out. underneath as shown. pull it forward. . Before replacing the dust cover, make sure IMPORTANT: Dust bags should be changed all edges of dust bag regularly for the maximum efficiency of the filters are completely.
Central Filter (Fig. 1) Part no. AMCBFIZW1000 The central filter (foam filter), is installed in the dust bag compartment to protect the motor from dirt. Simply rinse it out in warm water and dry It thoroughly before replacing. To remove the central the fitter at the top (as illustrated) and pull it towards you. IMPORTANT: Ensure that the filter is completely dry before re-installing it into the cleaner. Clean Alr Filter (Flg.
Before returning the vacuum cleaner to a Panasonic Service Center, check the hollowing points: TROUBLE CHECK POINT POSSIBLE SOLUTION Motor fails to rotate {no noise is heard at alkali. « Mains plug connection, « Ming plug fuse. {UK, IRL only} « Thermal cut out device may has operated. « Mains plug connected firmly and mains outset is ON.
SPECIFICATIONS MC-E581K / MC-E581 | MC-ES82K / MC-ES82 | MC-E588K / MC-E563 Power source Max. output 1500W 1600W 1600w Nominal output 1200-1300W 1300-1400W 1300-1400W Dimensions (WxLxH) mm 360x305x1100 360%305x1100 360x308x1100 Net weight 82kg Dusting brush v v/ v Upholstery nozzle v 7 v Service nozzle v v v Extension wand v v v §-Class Fitter v HEAP Filter v v Design and specifications may be changed without notice. Weight and dimensions shown are approximate.
