Operating Instructions Vacuum Cleaner MC-E465K, MC-E466K, MC-E467K -MC-E465, MC-E466, MC-E467 Panasonic We would particularly advise that you carefully study these Operating Instructions before attempting to operate the unit and that you note the Important Safety Instructions. This product complies with the European directives and 89/336/EEC and with the Australian Standards AS 3350.2.2 (1995} and Australian EMC requirements for the C-Tick Mark.
Page Page + Caution for AC Mains Lead (UK, Forlornly) .. 2 G) Automatic height adjustment 7 + Important Safety instructions for the user 3 H) Floor scratch prevention 7 * Cautions. 3 .I) How to use the accessories 8 * identification of carnal parts 4 ' J)Dust bag change indicator. 8 HOW TO ASSEMBLE / OPERATE YOUR CLEANER MAINTENANCE AND SERVICING A} Handle assembly 5§ * How to change the dust bag L B} Power cord release / storage 5§ .+ Filter care 2 C) ON/OFF Switch § -« Blockages .
When using this vacuum cleaner, please observe these basic precautions. WANING: To reduce the risk of fire, electric shock, or injury: +.Do not leave the vacuum cleaner plugged in to mains socket, Unplug from the socket when'not in use and before cleaning the appliance or undertaken maintenance operations. + Electric shocks can scour If used outdoors or on wet surfaces.
HOW TO ASSEMBLE / OPERATE YOUR CLEANER 1) Insert the base of the handle 2) Set the hose around the hose into the top of the body of the clip. machine as shown. Push in NOTE: Always place the hose in handle and tighten the scree. the clockwise direction. IMPORTANT: Do not over tighten the screw, Upper cord hook 3) Turn the upper cord hook in the upright position and wind the power cord around the upper and lower cord hooks.
These vacuum cleaners incorporate a variable power control to select the most suitable power required for your cleaning needs. MIN: To clean curtains and soft furnishing's st, with tool attached. |/ \Discussant I ] i MAX: To.clean with high suction continuously on carpets. 1} Upright position The handle should be in an upright position when cleaning tools are used. 2) Middle position For normal cleaning, depress the foot pedal and pull back the handier to.
Her cleaning carpeted surfaces, slide the switch to the "BEATER BAR” position. When cleaning on hard floors or when using the accessories, slide the switch-to the “STOP” position to stop the brush from rotating. NOTE: Ensure that the vacuum cleaner Is switched on before macing the bilateral bar switch, € | Your Panasonic vacuum cleaner is designed with an Automatic Height Adjustment, which adjusts the cleaning head to the proper height of any Capet pile.
1) Té use the accessories keep the vacuum cleaner’ in upright position and slide the beater bar switch 0" STOP * position 10 stop the rotary brush rotating, 2) Pull out the hose from tha rear side of the vacuum cleaner and remove the hose from the hose clip and support. Then connect any accessory as illustrated .. NOTE: After having finished using the accessories, Ra-insert the hose to the suction inlet and re-install the hose Into the hose clip and support.
Maintenance AND SERVICING IMPORTANT NOTE: Before servicing any part, aiw. DISCONNECT THE CLEANER FROM THE ELECTRICITY MAINS 1) Remove dust cover simply 2) Grip the cardboard of the dust ™ 3) Install the dust bag by pressing pulling it forwards. bag and pull out. the cardboard as shown. Before replacing the dust cover, make sure all ages of the dust bag are completely IMPORTANT: Dust bags should be changed regularly for the . Inside the bag compartment.
If your cleaner stops picking up dust, or the dust bag check indicator shows "Full" while the dust . bag is stile empty, a blockage may have occurred, Remove the hose from the suction inlay, push the smalls clips inwards, tum the hose right and pull it upwards (Fig. 1). Cesar any obstruction from the hose and/or suction inlet using a bunt implement, taking care not to damage the hose. . If the obstruction occurs in the suction pipe inlet, it can be removed with care as shown in Fig. 2.
e Before replacing any part DISCONNECT THE CLEANER FROM THE MAINS SUPPLY. We always recommend you use genuine Panasonic replacement parts only. If you have any query, contact your local Panasonic dealer / service agent. To replace any of the following parts, place the vacuum cleaner in the horizontal position by using the pedal. Then turn it over exposing the underside. -HOW TO REPLACE DRIVE BELT TYPE UB-1L./ ROTARY BRUSH ASSEMBLY 1. Remove the 4 screws from the base plate and lift it off. (Fig. 1) o .
Before returning the vacuum cleaner to a Panasonic Service Center, check the following points: Trouble Check Point Gauss / Remedy Motor fails to'rotate {no * Mains plug connection, * Mains plug connected firmly and noise is heard at all). < . mains outlet is on, * Mains plug fuse. N » Check fuse and replace if blown: Motor runs but no suction, + Hose inlet clogged.. + f there is a blockage, remove it » Check dust indicator, . * If shows full, replace the paper bag. Paper bag broken.
