Operating Instructions Vacuum Cleaner MC-E460K, MC-E461K, MC-E463K MC-E460, MC-E461, MC-E463 Panasonic ‘Wae would particularly advise that you carefully study these Operating instructions before attempting to operate the unit and that you note the Important Safety instructions. . This product complies with the European directives 73/23/EEC and 89/336/EEC and with the Australian Standards AS 3350 2.2 (1995} and Australian EMG requirements for the C-Tick Mark.
Page Page * Caution for AC Mains Lead (UK, iRL only} ...2 G} Automatic height adjustment 7 * important Safety instructions for the user 3 Hj Floor scratch prevention 7 « Cautions How to use the accessories 8 + [identification of main parts . 4 . J)Dust bay change oratorical. 8 HOW TO ASSEMBLE / OPERATE YOUR CLEANER MAINTENANCE AND SERVICING A} Handle assembly 5 = How to change the dust bag 8 B} Power cord release / storage 5 s Filter care 8 C} ON/OFF Switch & «Blockages . .
‘When using this vacuum cleaner, please observe these basic precautions. WARNING: To reduce the risk of fire, electric shock, or injury: + Do not leave the vacuum cleaner plugged in to mains outset. Unplug from the outlast when not in use, and before cleaning the appliance or undertaken maintenance operations. * Electric shocks can occur if used outdoors or on wet surfaces.
© Cobain 3 {0} variable power control {MC-E4B3K, MC-E463 only) [isy e ..
HOW TO ASSEMBLE / OPERATE YOUR CLEANER 1) Insert the base of the handle into the top of the body of the clip. machine as shown. Push in handle and tighten the screw. IMPORTANT: Do not over tighten the screw. 2} Set the hose around the hose NOTE: Always place the hose in the clockwise direction. Lower cord hook/ Carrying handier 3] Tum the upper cord hook in the upright position and wind the power cord around the upper and lower cord hooks.
“These vacuum cleaners incorporate a variable power control 1o select the most suitable power required for your cleaning needs. MIN: To clean curtains and soft furnishing's i, with tool attached, 4 MAX: To clean with high suction continuously on carpets. Ta' lower the body of the cleaner, step on the pedal at the left rear comer of the vacuum cleaner, 1) Upright position ‘The handle should be in an upright position when cleaning tools ars used.
When cleaning carpeted surfaces, slide the switch to SWITCH BEATER BAR ON OR OFF the “BEATER BAR” partition. When cleaning on hard floors or when using the // accessories, slide the switch to the “STOP" position to stop the brush from rotating. NOTE: Ensure that the vacuum cleaner is switched on before moving the baster bar switch. Your Panasonic vacuum cleaner is designed with an Automatic Height Adjustment, which adjusts the cleaning head to the proper height of any carpet pile.
1) To uss the accessories keep the vacuum cleaner in upright position and slide the beater bar switch to ¥ STOP " position to stop the rotary brush rotating, 2) Pull out the hose from the rear side of the vacuum cleaner and remove the hose from the hose clip and support. Then connect any accessory as lust rated . NOTE: After having finished using the accessories; re-insert the hose to the suction inlet and re-install the hose into the hose clip and support.
MAINTENANCE AND SERVICING IMPORTANT NOTE: Before ng any part, airways DISCONNECT THE CLEANER FROM THE ELECTRICITY MAINS 1) Remove dust cover simply 2) Grip the cardboard of the dust . 3} Install the dust bag by pressing pulling it forwards, bag and pull out. the cardboard as shown. Before replacing the dust cover, make sure all edges of .the dust bag are completely IMPORTANT: Dust bags should be changed regularly for the inside the bag compartment.
I¥ your cleaner stops ta pick up dust, or the dust bag check indicator shows "Full” while the dust bag is stile empty, a blockage may have occurred. Remove the hose from the suction inlet, push the smalls clips inwards, turn the hose right and pull it upwards (Fig. 1). Clear any obstruction from the hose and/or suction inlet using a bunt implement, taking care not to damage the hose. If the obstruction scours in the suction pipe inlet, it can be removed with care as shown in Fig. 2.
Before replacing any part DISCONNECT THE CLEANER FROM THE MAINS SUPPLY. We always recommend you use genuine Panasonic replacement parts only. If you have any query, contact your local Panasonic dealer / service agent. To replace any of the following parts, place the vacuum cleaner in the horizontal position by using the pedal. Then turn it over exposing the underside. HOW TO REPLACE DRIVE BELT TYPE UB-1L / ROTARY BRUSH ASSEMBLY 1. Remove the 4 screws from the base plate and fight it off.
Before returning the vacuum cleaner to.a Panasonic Service Center, check the following points: ' Trouble Check Point Cause / Remedy Motor fails to rotate {no noise is heard at al). = Mains plug connection. * Mains plug fuse. * Ming plug connected firmly and mains outset is on. * Check fuse and replace if blown. Motor runs but no suction. * Hose inlet clogged. * Check dust indicator, * Paper bag broken. + [f there is a blockage, remove it.
