Operating Instructions Digital Corded/Cordless Answering System Model No. KX-TGF350 KX-TGF352 KX-TG572SK KX-TGF353 Model shown is KX-TGF350. Before initial use, see “Getting Started” on page 8. Thank you for purchasing a Panasonic product. Please read these operating instructions before using the unit and save them for future reference. Consulte “Guía Rápida Española”, página 57. For assistance, visit our Web site: www.panasonic.com/support for customers in the U.S.A. or Puerto Rico.
Table of Contents Introduction Answering system settings ...............................44 Model composition ..............................................3 Accessory information ........................................3 Useful Information Important Information For your safety ....................................................5 Important safety instructions ...............................6 For best performance .........................................6 Other information ...............................
Introduction Model composition Series Model No. Base unit Handset Part No. Part No. KX-TGF350 series KX-TGF350 KX-TGF350 KX-TGFA30 Quantity 1 KX-TGF352 KX-TGF350 KX-TGFA30 2 KX-TG572SK KX-TGF350 KX-TGFA30 2 KX-TGF353 KX-TGF350 KX-TGFA30 3 Accessory information Supplied accessories Quantity No.
Introduction Additional/replacement accessories Please contact your nearest Panasonic dealer for sales information (page 61). Accessory item Model number/Specifications Rechargeable batteries HHR-4DPA*1 R To order, please visit www.panasonic.
Important Information For your safety To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING the frequency range of 1.92 GHz to 1.93 GHz, and the RF transmission power is 115 mW (max.).) R Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so.
Important Information Note when using alkaline batteries for power backup R The batteries should be used correctly, otherwise the unit may be damaged due to battery leakage. R Do not charge, short-circuit, disassemble, or heat the batteries. R Do not dispose of batteries in a fire. R Remove all the batteries when replacing. R Do not mix old, new or different types of batteries. R It is recommended that batteries are replaced annually. R It is recommended that batteries are replaced after a power outage.
Important Information Specifications R Standard: DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0) R Frequency range: 1.92 GHz to 1.93 GHz R RF transmission power: 115 mW (max.) R Power source: 120 V AC, 60 Hz R Power consumption: Base unit: Standby: Approx. 0.7 W Maximum: Approx. 3.0 W Charger: Standby: Approx. 0.1 W Maximum: Approx. 1.8 W R Operating conditions: 0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 % relative air humidity (dry) For assistance, please visit www.panasonic.
Getting Started Note: R Use only the supplied Panasonic AC adaptor PNLV226. Setting up Connections n Base unit Connect the AC adaptor to the unit by pressing the plug firmly. Connect the telephone line cord to the unit until you hear a click. Fasten the AC adaptor cord and the telephone line cord by hooking it. Connect the AC adaptor to the power outlet. Connect the telephone line cord to the single-line telephone jack (RJ11C) until you hear a click.
Getting Started Handset battery charging Charge for about 7 hours. R Confirm “Charging” is displayed (1). R When the batteries are fully charged, “Fully charged” is displayed. 1 Handset battery level Icon Battery level – Standard (non-rechargeable) alkaline batteries*3 R Do NOT use manganese batteries. R Confirm correct polarities ( , ). *1 The base unit can fully charge Ni-MH batteries in about 15 hours. *2 We recommend using HHR-4DPA batteries (page 4).
Getting Started *1 If begins flashing on the base unit, replace the batteries with new ones as soon as possible. If you replace Ni-MH batteries with alkaline batteries, insert the Ni-MH batteries into the base unit again after the power is restored so that they will be recharged. Battery saving mode setting This feature allows the base unit to reduce its power consumption by limiting the available functions and therefore extend battery life during a power failure.
Getting Started – VOL. (Volume: MDN or MCN): Adjust the receiver or speaker volume while talking. – MFN : View the phonebook entry. – MEN REDIAL: View the redial list. – MCN CID (Caller ID): View the caller list.
Getting Started MCALL BLOCKN M N (ANSWER ON/OFF) ANSWER ON/OFF indicator MERASEN M N (PLAY/STOP) Message indicator Desk stand/Wall mounting adaptor R The adaptor is a removable attachment for desk stand or wall mounting use (page 47). n Control type Soft keys By pressing a soft key, you can select the feature shown directly above it on the display. Navigator key – MDN, MCN, M N, or M N: Scroll through various lists and items. – VOL. (Volume: MDN or MCN): Adjust the receiver or speaker volume while talking.
Getting Started 3 Proceed with the operation for your unit. Handset: MOFFN Base unit: MEXITN Voice guidance language You can select either “English” or “Español” as the voice guidance language of the answering system. The default setting is “English”. You can configure this setting using either the base unit or one of the handsets. Handset / Base unit 1 2 3 MMENUN#112 MbN: Select the desired setting. a MSAVEN Proceed with the operation for your unit.
Making/Answering Calls B Base unit: Place the corded handset on the cradle. When the speakerphone is used, press MZN. Making calls Using the handset Using the speakerphone 1 1 During a conversation with the corded handset, press MZN to turn on the speakerphone. R You can place the corded handset on the cradle. R Speak into the base unit microphone. 2 When you finish talking, press MZN. 2 3 Lift the handset and dial the phone number. R To correct a digit, press MCLEARN.
Making/Answering Calls Example: If you need to dial the line access number “9” when making outside calls with a PBX: Useful features during a call Handset 1 2 Hold 9 a MDN (Pause) Dial the phone number. a M N 1 2 3 Base unit 1 2 3 Handset 9 a MPAUSEN Dial the phone number. Lift the corded handset. Note for handset and base unit: R A 3.5 second pause is inserted each time you press MDN (Pause) on the handset or MPAUSEN on the base unit.
Making/Answering Calls For call waiting or Call Waiting Caller ID service users To use call waiting or Call Waiting Caller ID, you must first subscribe with your phone service provider. This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a call waiting tone.
Making/Answering Calls – between 2 handsets – between a handset and the base unit Handset 1 2 3 4 During an outside call, press MMENUN. 5 To complete the transfer: Press MOFFN. To establish a conference call: MMENUN a MbN: “Conference” a MSELECTN R To leave the conference, press MOFFN. The other 2 parties can continue the conversation.
Intercom 2 Intercom Intercom calls can be made: – between handsets – between a handset and the base unit Note: R When paging unit(s), the paged unit(s) beeps for 1 minute. R If you receive an outside call while talking on the intercom, the interrupt tone sounds. – Handset: To finish intercom, press MOFFN. To answer the call, press M N. – Base unit: To finish intercom, place the corded handset on the cradle. If the speakerphone is used, press MZN. To answer the call, lift the corded handset.
Call Block Using the MCALL BLOCKN button You can press the MCALL BLOCKN button in the following situations to disconnect the current call and add a phone number to the call block list: – when an incoming call is being received – when an incoming call is being recorded by the answering system – when talking on an outside call Once a phone number has been added to the call block list, the unit will block calls from that phone number in the future.
Call Block 2 MbN: “Block a single number” a MSELECTN 3 4 5 MMENUN a MbN: “Add” a MSELECTN Enter the phone number (24 digits max.). MSAVEN a MOFFN Setting not to ring once for blocked call If you do not want the unit to sound one ring for calls from phone numbers stored in the call block list, select “No”. The default setting is “Yes”. Base unit Handset / Base unit 1 2 MCALL BLOCKN 3 4 Enter the phone number (24 digits max.).
Call Block Erasing all call block numbers Handset / Base unit 1 2 MCALL BLOCKN 3 Proceed with the operation for your unit. Handset: MMENUN a MbN: “Erase all” a MSELECTN Base unit: MERASEN 4 5 6 MbN: “Yes” a MSELECTN MbN: “Block a single number” or “Block range of numbers” a MSELECTN MbN: “Yes” a MSELECTN Proceed with the operation for your unit. Handset: MOFFN Base unit: MEXITN For assistance, please visit www.panasonic.com/support TGF35x(en)_1205_ver041.
Phonebook Phonebook You can add 100 names (16 characters max.) and phone numbers (24 digits max.) to the phonebook, and assign each phonebook entry to the desired group (page 23). Important: R All entries can be shared by the base unit and any registered handset. Key Character 6 M N O 6 m n o 6 P Q R S 7 p q r s 7 T U V 8 t u v 8 W X Y Z 9 w x y z 9 7 8 9 0 Adding phonebook entries 0 # Handset / Base unit 1 Proceed with the operation for your unit.
Phonebook 2 3 4 5 MbN: Select the desired entry. a MMENUN R To edit the number: MbN: “Edit” a MSELECTN Press MEDITN repeatedly until the phone number is shown in the desired format. And then, press MSAVEN. Go to step 4. MbN: “Save caller ID” a MSELECTN 6 Finding and calling from a phonebook entry MbN: “Phonebook” a MSELECTN Continue from step 3, “Editing entries”, page 23. Base unit 1 2 MCIDN 3 4 5 MSAVEN Handset / Base unit 1 Proceed with the operation for your unit.
Phonebook Erasing entries Erasing an entry Handset 1 2 3 Find the desired entry (page 23). MMENUN a MbN: “Erase” a MSELECTN R If you have rotary/pulse service, you need to on press * (TONE) before pressing MFN the handset or M N on the base unit in step 1 to change the dialing mode temporarily to tone. When adding entries to the phonebook, we recommend adding * (TONE) to the beginning of phone numbers you wish to chain dial (page 22).
Phonebook 4 Enter the party’s phone number (24 digits max.). a MOKN 5 MSELECTN a MEXITN 3 4 MbN: “Yes” a MSELECTN MOFFN Base unit n From the phonebook: 1 MSPEED DIALN 2 MbN: Select the desired speed dial key. a M N 3 4 MbN: Select the desired entry. MSAVEN a MEXITN Note for handset and base unit: R If you edit a phonebook entry which is assigned to a speed dial key, the edited entry does not transfer to the speed dial key.
Phonebook Adding phone numbers for outside calls MERASEN a MbN: “Yes” a MSELECTN a MEXITN Making a call Base unit n By entering phone numbers: 1 Press and hold the desired one-touch dial button (1 to 3). a MEDITN 2 Enter the party’s name (16 characters max.). a MOKN 3 Enter the party’s phone number (24 digits max.). a MOKN 4 MSELECTN a MEXITN Base unit Press the desired one-touch dial button (1 to 3), then lift the corded handset.
Programming Menu list To access the features, there are 2 methods. Handset / Base unit n Scrolling through the display menus 1 MMENUN 2 3 4 Press MCN or MDN to select the desired main menu. a MSELECTN Press MCN or MDN to select the desired item from the next sub-menus. a MSELECTN Press MCN or MDN to select the desired setting. a MSAVEN n Using the direct command code 1 MMENUN a Enter the desired code. Example: Press MMENUN#101. 2 Select the desired setting.
Programming Sub-menu 1 Sub-menu 2 Greeting Record greeting*1 – #302 / 39 Check greeting – #303 / 40 Pre-recorded*1 (Reset to pre-recorded greeting) – #304 / 39 #338 / 41 New message alert*1 Outgoing call – On/Off Settings On Outgoing call – Notification to Settings Code Unit – Outgoing call – Remote code Activate Base unit beep On #339 / 41 Ring count*1 2-7 rings <4 rings> Toll saver #211 / 44 Recording time*1 1 min <3 min> Greeting only*2
Programming Main menu: “Speed dial” Operation Code Viewing the speed dial entry.
Programming Sub-menu 1 Sub-menu 2 Call block*1 Block a single number Settings – Code Block range of numbers – #217 Unit / 19 / 20 Block unknown CID Block (CID: Caller ID) #240 / 20 One ring for blocked call #173 / 20 No One-touch dial – – #247 Speed dial – – #261 / 24 Record greeting*1 – – #302 / 39 – #331 / 46 Off #332 / 46 Handset: Level 1-4 <2> Base unit: Level 1-6 <3> #145 / – Voicemail Save VM access#*1, *9 (VM: Voicemail) Save Voi
Programming Sub-menu 1 Sub-menu 2 Settings Code Set tel line*1 Set dial mode Pulse #120 / 13 Set flash time*12 900 ms <700 ms> 600 ms 400 ms 300 ms 250 ms 200 ms 160 ms 110 ms 100 ms 90 ms 80 ms #121 / 15 Set line mode*13 A #122 / – Off #194 / 16 – Call sharing*1 Registration Register handset – #130 36 Deregistration*2 – #131 36 – – #131 36 On #150 10 Display Español #110 / 12 Voice prompt*1 Español #112 / 13 Deregi
Programming *1 If you program these settings using one of the units, you do not need to program the same item using another unit. *2 This menu is not displayed when scrolling through the display menus. It is only available in direct command code. *3 This feature allows the unit to automatically adjust the date and time each time caller information including date and time is received. To turn this feature on, select “Caller ID auto”. To turn this feature off, select “Manual”.
Programming 8 MbN: Select the desired alarm tone. a MSELECTN R We recommend selecting a different ringer tone from the one used for outside calls. 1 2 MMENUN#238 9 MbN: Select the desired snooze setting. a MSAVEN 3 10 MSELECTN a MOFFN Enter the desired hour and minute you wish to start this feature. 4 5 MAM/PMN: Select “AM” or “PM”. a MOKN 6 7 MAM/PMN: Select “AM” or “PM”. Note: R Press MSTOPN to stop the alarm completely.
Programming test its sensitivity. Check the connection if you are diverting the baby monitor to an outside line. R This feature should not be used as a substitute for a medical or caregiver’s supervision. It is the caregiver’s responsibility to stay close enough to handle any eventuality. Note: R If the unit is connected to a PBX system, you cannot set the baby monitor. R During the monitoring mode, battery consumption is faster than usual. We recommend leaving the monitored handset on charger.
Programming 5 6 7 *1 If MMUTEN is pressed, press MZN 2 times. MMENUN a MbN: “Edit” a MSELECTN Edit the name if necessary. a MOKN Edit the phone number if necessary. a MOKN a MSELECTN Erasing an outside monitoring number Handset 1 Press MMENUN on the handset being monitored. 2 3 4 5 6 MbN: “On/Off” a MSELECTN n When monitoring from an outside line: Answer the call. If you want to respond from your monitoring phone, press #1 using tone dialing. You can turn off the baby monitor feature by pressing #0.
Programming Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to the base unit. Important: R See page 4 for information on the available model. Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. 1 Handset: MMENUN#130 2 Base unit: Press and hold MLOCATORN for about 5 seconds.
Caller ID Service Using Caller ID service Important: R This unit is Caller ID compatible. To use Caller ID features, you must subscribe to a Caller ID service. Contact your phone service provider for details. Caller ID features Handset / Base unit When an outside call is being received, the caller information is displayed. Caller information for the last 50 callers is logged in the caller list from the most recent call to the oldest.
Caller ID Service Note for handset and base unit: R If the entry has already been viewed or answered, “ ” is displayed. R In step 1, you can also access the caller list as follows: Base unit: MCALL LOGN a MbN: “Incoming call” a MSELECTN Editing a caller’s phone number You can edit a phone number in the caller list by removing its area code and/or the long distance code “1”. Handset 1 2 3 4 MCN CID 5 M MbN: Select the desired entry.
Answering System Answering system The answering system can answer and record calls for you when you are unavailable to answer the phone. You can also set the unit to play a greeting message but not to record caller messages by selecting “Greeting only” as the recording time setting (page 45). Important: R Make sure the unit’s date and time setting is correct (page 13). Memory capacity (including your greeting message) The total recording capacity is about 17 minutes.
Answering System Handset / Base unit 1 2 3 Operating the answering system during playback MMENUN#304 MYESN Key Operation Proceed with the operation for your unit. Handset: MOFFN Base unit: MEXITN MDN or MCN Adjust the speaker volume M N Repeat message*1 M N Skip message Playing back the greeting message MPAUSEN Pause message To resume playback, press M N. Handset / Base unit 1 2 MMENUN#303 M Proceed with the operation for your unit. Handset: To exit, press MOFFN.
Answering System Key Operation 2 or MEN Skip message (during playback) 3 Enter the “Settings” menu 4 Play new messages 5 Play all messages Audible message alert 6 Play greeting message 76 Record greeting message 8 Turn answering system on MPAUSEN Pause message*2 9 or MSTOPN Stop recording Stop playback This feature allows the base unit to beep to inform you of a new message arrival when new messages are recorded.
Answering System 2 MbN: “Notification to” a MSELECTN a MADDN 3 4 MbN: “Phonebook” a MSELECTN MbN: Select the desired phonebook entry. a MSAVEN a MOFFN n By entering a phone number: 1 MMENUN#338 3 4 MMENUN a MbN: “Edit” a MSELECTN 5 Edit the phone number if necessary (24 digits max.). a MOKN a MSELECTN a MOFFN Edit the name if necessary (16 characters max.). a MOKN Base unit 1 2 MMENUN#338 MbN: “Manual” a MSELECTN 3 Enter the desired name (16 characters max.).
Answering System 4 Proceed with the operation for your unit. Handset: MOFFN Base unit: MEXITN Listening to messages After you answer the new message alert, you can listen to the messages as follows. n When the remote access code is set to “Inactivate”: Press 4 to play the new message during the announcement. n When the remote access code is set to “Activate”: 1 Enter the remote access code (page 43) during the announcement. 2 Press 4 to play the new message.
Answering System 3 Key Operation 2 Skip message (during playback) 4 Play new messages 5 Play all messages 9 Stop playback*2 Start voice guidance*3 0 Turn answering system off *4 Erase currently playing message *5 Erase all messages *# End remote operation (or hang up) *1 If pressed within the first 5 seconds of a message, the previous message is played.
Answering System the voicemail service provided by your phone service provider before changing this setting. – Change the number of rings of the voicemail service so that the answering system can answer the call first. To do so, contact your phone service provider. Caller’s recording time You can change the maximum message recording time allowed for each caller. The default setting is “3 min”. You can configure this setting using either the base unit or one of the handsets.
Useful Information Voicemail service Voicemail is an automatic answering service offered by your phone service provider. After you subscribe to this service, your phone service provider’s voicemail system answers calls for you when you are unavailable to answer the phone or when your line is busy. Messages are recorded by your phone service provider, not your telephone. Please contact your phone service provider for details of this service.
Useful Information Handset / Base unit 1 2 3 MMENUN#330 R The speakerphone turns on. R Lift the corded handset if needed. Follow the pre-recorded instructions. When finished, hang up. Note: R You can also use the MACCESSN soft key, if displayed, to play new voicemail messages. R If the handset and base unit still indicate there are new messages even after you have listened to all new messages, turn it off by pressing and holding # until the handset or base unit beeps.
Useful Information 3 Insert the lower tabs of the adaptor into the unit’s bottom slots (A), then insert by pushing down the levers of the adaptor into the upper slots (B). R The words “UP WALL” should be facing up. B B A A 4 Mount the unit on a wall then slide down to secure in place. R This product is compliant with the following wall phone plate sizes (2 types).
Useful Information Error messages Display message Cause/solution Ask phone company for VM access # R You have not stored the voicemail access number. Store the number (page 46). Base no power or No link. Reconnect base AC adaptor. R Confirm the base unit’s AC adaptor is connected to the unit and the power outlet correctly. R The handset has lost communication with the base unit. Move closer to the base unit and try again. R Unplug the base unit’s AC adaptor to reset the unit.
Useful Information Problem Cause/solution The unit does not work. R Make sure the batteries are installed correctly (page 8). R Fully charge the batteries (page 9). R Check the connections (page 8). R Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. R The handset has not been registered to the base unit. Register the handset (page 36). I cannot hear a dial tone. R The base unit’s AC adaptor or telephone line cord is not connected. Check the connections.
Useful Information Problem Cause/solution Noise is heard, sound cuts in and out. R You are using the handset or base unit in an area with high electrical interference. Re-position the base unit and use the handset away from sources of interference. R Move closer to the base unit. R If you use a DSL/ADSL service, we recommend connecting a DSL/ADSL filter between the base unit and the telephone line jack. Contact your DSL/ADSL provider for details. The handset or base unit does not ring.
Useful Information Problem Cause/solution The 2nd caller’s information is not R In order to use Caller ID, call waiting, or Call Waiting Caller ID displayed during an outside call. (CWID), you must first contact your phone service provider and subscribe to the desired service. After subscribing, you may need to contact your phone service provider again to activate this specific service, even if you already subscribed to both Caller ID and Call Waiting with Caller ID services (CWID).
Useful Information Liquid damage Problem Cause/solution Liquid or other form of moisture has entered the handset/base unit. R Disconnect the AC adaptor and telephone line cord from the base unit. Remove the batteries from the handset and leave to dry for at least 3 days. After the handset/base unit are completely dry, reconnect the AC adaptor and telephone line cord. Insert the batteries and charge fully before use. If the unit does not work properly, contact an authorized service center.
Useful Information FCC and other information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------. If requested, this number must be provided to the telephone company. R Registration No.............(found on the bottom of the unit) R Ringer Equivalence No. (REN).......0.
Useful Information CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. R The handset may be carried and operated with only the specific provided belt-clip. Other non-tested belt-clips or similar body-worn accessories may not comply and must be avoided. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Useful Information canceled when the corded handset comes off during or after setting up. n To deactivate the charge only mode: – Lift the corded handset from the base unit and replace it. – Press any key. – 24 hours passed after activating the charge only mode. For assistance, please visit www.panasonic.com/support 56 TGF35x(en)_1205_ver041.
Guía Rápida Española Guía Rápida Española Conexiones Unidad base 1 Conecte el adaptador de corriente alterna a la unidad presionándolo firmemente. 2 Conecte el cable de la línea telefónica a la unidad hasta que escuche un clic. 3 Enganche el cable del adaptador de corriente alterna y el cable de la línea telefónica para fijarlos. 4 Conecte el adaptador de corriente alterna a la toma de corriente.
Guía Rápida Española Sugerencias de operación Teclas de función Al oprimir una tecla de función, puede seleccionar la función que aparece directamente encima de ella en la pantalla. Preste atención a la pantalla para ver qué funciones están asignadas a las teclas de función durante la operación. Tecla navegadora Auricular: − {^}, {V}, {<}, o {>}: Navegue por diversas listas y elementos. − VOL. (Volumen: {^} o {V}): Ajuste el volumen del receptor o el altavoz mientras habla.
Guía Rápida Española Grabación de su mensaje de saludo en el contestador automático (Auricular/ Unidad base) Puede grabar su propio mensaje de saludo en lugar de usar uno pregrabado. 1 {MENU}(3)2 s {r}: “Sí” s {SELEC.} 2 Después de que suene un pitido, hable con claridad en el micrófono a una distancia aproximada de 20 cm (8 pulgadas) (máx. de 2 minutos). 3 Oprima {PARAR} para dejar de grabar. 4 Continúe operando su unidad.
Guía Rápida Española Operaciones básicas Contestador de llamadas (Unidad base) Contestador encendido/apagado Oprima {s} para encender y apagar el contestador de llamadas. Para escuchar mensajes {P} (PLAY) Sistema contestador de llamadas (auricular) Para escuchar mensajes Para escuchar mensajes nuevos: {REPRO.} o {MENU}(323 Para escuchar todos los mensajes: {MENU}(324 Preguntas frecuentes Pregunta Causa y solución ¿Por qué aparece _? L El auricular está demasiado lejos de la unidad base. Acérquelo.
Appendix Customer services Shop Accessories! for all your Panasonic gear Go to www.panasonic.com/accessories Get everything you need to get the most out of your Panasonic products Accessories & Parts for your Camera, Phone, A/V products, TV, Computers & Networking, Personal Care, Home Appliances, Headphones, Ba!eries, Backup Chargers & more… Customer Services Directory For Product Informa"on, Opera"ng Assistance, Parts, Owner’s Manuals, Dealer and Service info go to www.panasonic.
Appendix Warranty (For United States and Puerto Rico) Panasonic Telephone Products Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b)
Appendix Limited Warranty Limits And Exclusions This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage.
Index H Index # A 3-way conference: 16 Additional handset: 36 Alarm: 32 Answering calls: 15 Answering system Call screening: 44 Erasing messages: 40, 41, 44 Greeting message: 39 Greeting only: 45 Listening to messages: 40, 43 New message alerting: 41 Number of rings: 44 Recording time: 45 Remote access code: 43 Remote operation: 43 Ring count: 44 Toll saver: 44 Turning on/off: 39 Auto intercom: 18 Auto talk: 15, 30 B Baby monitor: 33 Battery: 8, 10 Battery saving mode: 10 Booster (Clarity booster): 16 C C
Notes 65 TGF35x(en)_1205_ver041.
Notes 66 TGF35x(en)_1205_ver041.
Notes 67 TGF35x(en)_1205_ver041.
IMPORTANT! If your product is not working properly. . . 1 Reconnect AC adaptor to the base unit. 2 Check if telephone line cord is connected. 3 Use rechargeable Ni-MH batteries. (Alkaline/Manganese/Ni-Cd batteries CANNOT be used.) 4 Read troubleshooting page in the Operating Instructions. Visit our Web site: www.panasonic.com/support L FAQ and troubleshooting hints are available. For your future reference We recommend keeping a record of the following information to assist with any repair under warranty.
