TG106x_QG(e).fm Page 1 Friday, December 19, 2008 2:55 PM Model No. KX-TG1061 KX-TG1062 KX-TG1063 Quick Guide Setting up Base unit L Use only the supplied Panasonic AC adaptor PQLV219. Correct Press plug firmly. Base unit “Click” “Click” Wrong Hook Base unit “Click” (120 V AC, 60 Hz) “Click” To single-line telephone jack (RJ11C) DSL/ADSL filter* (Not supplied) *For DSL/ADSL service users Handset L USE ONLY Ni-MH batteries AAA (R03) size. L Do NOT use Alkaline/Manganese/Ni-Cd batteries.
TG106x_QG(e).fm Page 2 Friday, December 19, 2008 2:55 PM Operating tips Navigator key/Volume key (VOL., ?) N Scrolling through lists or items By pressing this key ({^} or {V}) repeatedly, you can scroll through (up or down) various lists or items. N Adjusting the volume By pressing this key ({^} or {V}) repeatedly, you can adjust the receiver or speaker volume (up or down) while talking.
TG106x_QG(e).fm Page 3 Friday, December 19, 2008 2:55 PM Basic operations Making/Answering calls (Base unit/Handset) Making calls Base unit: Dial the phone number. i Lift the corded handset, or press {SP-PHONE}. Handset: Dial the phone number. i {C}/{s} Answering calls Base unit: Lift the corded handset, or press {SP-PHONE}. Handset: {C}/{s} To hang up Base unit: Place the corded handset on the cradle. When the speakerphone is used, press {SP-PHONE}.
TG106x_QG(e).fm Page 4 Friday, December 19, 2008 2:55 PM Frequently asked questions Question Cause/solution Why is w flashing? L The handset is too far from the base unit. Move closer. L The base unit’s AC adaptor is not properly connected. Reconnect AC adaptor to the base unit. L You are using the base unit or handset in an area with high electrical interference. Re-position the base unit and use the handset away from sources of interference. L The handset is not registered to the base unit.
TG106x_QG(e).fm Page 5 Friday, December 19, 2008 2:55 PM Quick troubleshooting 1 Cordless handset shows: “No link. Reconnect base AC adaptor.” Move closer to the base unit. Unplug, then plug the AC adaptor properly to the base unit and AC outlet. “No link. Reconnect base AC adaptor.” is still displayed. Remove the batteries for 10 seconds from the handset, and then insert the batteries into the handset again. “No link. Reconnect base AC adaptor.” is still displayed.
TG106x_QG(e).fm Page 6 Friday, December 19, 2008 2:55 PM Quick troubleshooting 2 No dial tone is heard from handset. See if “Check tel line” is shown on the handset display. Displayed Not displayed Lift up the handset from the charger. Press {C} at the handset, then check if the display shows “Talk”. {C} No link. Reconnect base AC adaptor. Check if the telephone cord is properly connected to both the base unit and telephone line jack on the wall. “No link. Reconnect base AC adaptor.” is displayed.
TG106x_QG(e).fm Page 7 Friday, December 19, 2008 2:55 PM Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. Handset {MENU} i {#}{1}{3}{0} {MENU} Base unit Press and hold {LOCATOR} for about 5 seconds until the registration tone sounds. L The next step must be completed within 90 seconds. Handset Press {OK}, then wait until a long beep sounds.
TG106x_QG(e).fm Page 8 Friday, December 19, 2008 2:55 PM IMPORTANT! If your product is not working properly ... 1 Reconnect AC adaptor to the base unit. 2 Check if telephone line cord is connected. 3 Use rechargeable Ni-MH batteries. (Alkaline/Manganese/Ni-Cd batteries CANNOT be used.) 4 Read FAQ in this Quick Guide and troubleshooting page in the Operating Instructions. Visit our web site: http://www.panasonic.
